-
Product
Probes With Lead Wires
-
Used when the probe is installed some distance from the logger, controller, or other data acquisition device. Available in a variety of lead wire types with stripped leads or connectors attached.
-
-
Product
Logic Probes
-
Logic probes allow you to capture signals using the logic portion of a mixed signal instrument. Yokogawa offers low and high voltage, isolated and non-isolated logic probes.
-
Product
High Impedance Probes
-
Everbeing offers GGB’s high impedance active probe for failure analysis of your devices. The high impedance with low capacitive design allows measurements of internal nodes without loading the device. For more information, please visit http://www.ggb.com.Everbeing offers GGB’s high impedance active probe for failure analysis of your devices. The high impedance with low capacitive design allows measurements of internal nodes without loading the device. For more information, please visit http://www.ggb.com.
-
Product
Differential Voltage Probes
DP150/DP200pro
-
The DP differential isolation probes are an important accessory for any laboratory involved in power electronics and high voltage systems. These probes allow isolated and floating measurements with any oscilloscope or data recorder, whilst the oscilloscope can remain grounded. Using a DP150 or DP200pro probe, differential and floating measurements can be made on a variety of ac power systems like 230V/110V ac input power supplies, chopped and switching power supplies, thyristor controllers, variable speed motor drives (PWM signals), motor inrush current and measurement across current shunts. The isolated input is made via two 4mm/banana safety sockets. The BNC output allows easy connection to an oscilloscope. The DP probes can be powered from a 9V battery or external power supply.
-
Product
RF Radio - Frequency Probes
-
*3 to 6 Ghz *PCB MCX SMB SMC *SMA U. FL MS / MM Fakra *Exchangeable inner plunger
-
Product
ATE Test Probes
-
For contacting loaded PCBs in automatic test equipment (ATE) with vacuum, pneumatic or mechanically operated fixtures. Available in 2.54mm, 1.91mm & 1.27mm test centre spacings.
-
Product
Optical Probes - Low Bandwidth
-
Depend on Tektronix to provide you with performance you can count on, and industry-leading service and support.*Broad Wavelength Response 500 to 950 nm or 1100 to 1700 nm*High-bandwidth DC up to 1.2 GHz*High Gain 1 V/mW*Low Noise <11 pW/√Hz*Probe Connects to DPO7000*1 and DPO/DSA/MSO70000*2Series*SONET/SDH and Fibre Channel Reference Receiver Performance
-
Product
General Purpose Test Probes
-
Low profile, short travel test probes for restricted space applicationsApplications where long travel is not required such as thin film/hybrid circuits or bareboard PCB testingReplaceable test probe by use of a receptacle
-
Product
RMP Replaceable General Purpose Probes
General Purpose Probe
Current Rating (Amps): 2Average Probe Resistance (mOhm): 125Test Center (mil): 20Test Center (mm): 0.51Full Travel (mil): 79Full Travel (mm): 2.01Recommended Travel (mil): 52Recommended Travel (mm): 1.33Mechanical Life (no of cyles): 50,000Overall Length (mil): 598Overall Length (mm): 15.19
-
Product
Probes
-
Fujian Lilliput Optoelectronics Technology Co., Ltd.
We are one of the leading and professional probes manufacturers and suppliers in China. Thanks to our highly qualified experts and advanced technology, we are also one of the world's leading brands. Welcome to buy the quality, cheap and durable probes in stock from us. Check the quotation with us now.
-
Product
Wide-Aperture Fiber-Optic Probes
Fiber-optic Probe
Wide-aperture Fiber-optic Probes and Very Wide-aperture Fiber-optic Probes are used to test dim or misaligned LEDs.
-
Product
Raman Fiber Probes
-
For ultimate flexibility, fiber-coupled Raman probes offer a compact design and a rugged, robust construction for a wide range of applications. With an optional integrated camera, the user can locate a precise region of interest prior to analysis. Also available are immersion probes and non-contact optics.
-
Product
C-S General Purpose Probes
General Purpose Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 45Full Travel (mm): 1.14Recommended Travel (mil): 30Recommended Travel (mm): 0.76Overall Length (mil): 395Overall Length (mm): 10.03Rec. Mounting Hole Size (mil): 46.5Rec. Mounting Hole Size (mm): 1.18Recommended Drill Size: 56
-
Product
LED Probes for testing
-
Advanced Probing Systems, Inc.
Probe Needles are used for the fabrication of most probe cards, however there exist applications for which these materials may not be appropriate, e.g., hubrid device and gold pad probing.
-
Product
Energy Probes
RjP-400 Series
-
The RkP-400 Series probes consist of a compact detector assembly, or head, and a preamplifier housed in a separate enclosure. The external dimensions of all the 400 Series Probes are the same, with identical detector planes, allowing for easy interchange of probes in an experiment. The heads have both ¼-20 and M6 tapped holes, a built-in 1" (25mm) filter holder, and a side-mounted BNC connector. Probe specific data, including spectral response curves and calibration dates, is stored in the preamplifier for access by the instruments.
-
Product
Fiber optic active antennas / field probes
EFS-105
-
The EFS-105 is the first in a family of fiber-optic active antennas & E-field probes. The field distortion caused by the probe head is nearly zero due to the exceptionally small probe head and the all-optical signal transmission and power supply. This gives an invaluable advantage for near field measurements and measurements close to metallic parts.
-
Product
Broadband Isotropic Field Strength Probes
PI-01, PI-01E, PI-03, PI-05
-
Modern design probes meeting the requirements of most EMC and RF safety standards for RF safety, industrial, military and radar communication applications: 0.2-1000 V/m, 10 KHz-40 GHz.
-
Product
Probes
-
Sper Scientific portfolio of probes provides the right solution for your testing needs, backed by years of product innovation and technical support. All of our probes are designed to meet the accuracy, ease of use, durability and flexibility for your water quality testing needs.
-
Product
Smart Probes
-
A wide selection of rugged smart probes for your sensing needs. From non-contact IR sensors to a full range of sensor types including Temperature, Humidity, Process, RTD, Thermocouple, pulse.
-
Product
Probes
-
Prepare the IM6/Zennium for special fields of application like high impedances, low impedances, very low capacitance or boost the compliance voltage.
-
Product
RF/High Frequency Probes
-
Everbeing is proud to distribute GGB Industries line of PicoProbes for customers everyday RF probing needs. The popular model 40A has been serving the needs of many high frequency researchers in the sub-40 GHz range. For more information on their products, visit www.ggb.com. If a product they sell is not shown here, we are still able to acquire for you. Please contact us for more details.
-
Product
AC Current Probes
CWT
-
Power Electronic Measurments Ltd
The CWT Rogowski current probe is suitable for measuring AC currents ranging from 300 milliamps to hundreds of kA from below 0.1Hz to >30MHz.
-
-
Product
DDR4 MSO Probes
-
The DDR4 DIIM and SO-DIMM Mixed Signal Interposers connect Address, Command and Control signals of a DDR4 bus to the Keysight V-Series Oscilloscopes with the MSO option. These interposers also provide accessibility to DDR4 signals for convenient analog probing. The user can then easily observe both the digital and analog representation of the DDR4 Address, Command and Control bus. Solder down N5541A analog probes purchased separately from Keysight Technologies.
-
-
Product
Near Field Probes
-
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
Product
High Voltage Passive Probes
-
The PPE6KV-A and HVP120 can handle up to 6000 Vpeak transient overvoltages and are designed for probing up to 2000 Vrms and 1000 Vrms respectively. Fast rise times, excellent frequency response, and a variety of standard accessories make these probes safe and ideal for high voltage measurement applications
-
Product
Test Probes
-
Test Probes provide the vital link to transfer measurement signals as true and as undistorted as possible. Therefore these elements can be regarded as the heart of Test Fixtures – and for this very reason it is important for Equip-Test to offer high performance Test Probes with best quality and value, and thus ensure maximized ROI (Return of Investment) for our customers. Test Probes supplied by Equip-Test always provide the best-possible available solution for your contacting demands.
-
Product
CP-059-025 Battery Probes
Battery Probe
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 57Full Travel (mm): 1.45Recommended Travel (mil): 40Recommended Travel (mm): 1.02Mechanical Life (no of cyles): 100,000Overall Length (mil): 313Overall Length (mm): 7.95
