-
Product
Probes Dissolved Oxygen
-
Specialized, in-line sensors that provide real-time, continuous monitoring of oxygen levels in liquid.
-
Product
UV Index Radiometric Probes
LPUVI02… Series
-
The radiometer LPUVI02 measures the global effective irradiance on a flat surface (Watt /m² effective), according to the requirements of the WMO for the measurement of UV-index.
-
Product
Current Probes
-
Current probes allow you to measure DC or AC current. Yokogawa's selection of current probes allow measurements ranges up to 500 ARMS and bandwidths up to 100MHz.
-
Product
Broadband Isotropic Field Strength Probes
PI-01, PI-01E, PI-03, PI-05
-
Modern design probes meeting the requirements of most EMC and RF safety standards for RF safety, industrial, military and radar communication applications: 0.2-1000 V/m, 10 KHz-40 GHz.
-
-
Product
Standard Pitch Spring Probes
-
Other than spring probes with gold plating, we have spring probe with anti-solder migration coating and plating that were developed by KITA. We also have anti-solder migration material for plunger tip. These are all included in “MARATHON” series. They have wide range of tip type for various use for every popular total length.
-
Product
OEM Raman Miniature Probes
-
- Minimum Range: 210cm-1, up to 4000 cm-1 however limited by spectrometer range- Optical design: Bandpass and longpass filters in proprietary layout- Fiber coupling: FC connectors- Fibers: Typically 100µm single fiber for Laser Excitation, TBD for Signal Collection- Spot Size: 100-125µm on sample (**Other spot sizes on request)- Working Distance: 9 to 10mm- Dimensions: 106 x 21 x 33mm / 4.2 x 0.9 x 1.3mm
-
Product
High Impedance Probes
-
Everbeing offers GGB’s high impedance active probe for failure analysis of your devices. The high impedance with low capacitive design allows measurements of internal nodes without loading the device. For more information, please visit http://www.ggb.com.Everbeing offers GGB’s high impedance active probe for failure analysis of your devices. The high impedance with low capacitive design allows measurements of internal nodes without loading the device. For more information, please visit http://www.ggb.com.
-
Product
Near-Field Probes 100 kHz up to 50 MHz
LF1 set
-
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.
-
Product
Beam Probes
-
The CO2 Laser Beam Probes are hand-held plates designed to simplify the alignment of IR optical systems. They display the laser beam as a dark image on a fluorescent background using the same UV-excited, thermal-sensitive surfaces developed for Macken Instruments'' Thermal Image Plates.
-
Product
Differential Probes (4-6 GHz)
-
Differential active probes are like two probes in one. Instead of measuring a test point in relation to a ground point (like single-ended active probes), differential probes measure the difference in voltage of a test point in relation to another test point. Dx10/Dx20/Dx00A-AT 4-6 GHz differential probes are a general purpose probing solution with high input dynamic range and offset.
-
Product
CP-059-025 Battery Probes
Battery Probe
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 57Full Travel (mm): 1.45Recommended Travel (mil): 40Recommended Travel (mm): 1.02Mechanical Life (no of cyles): 100,000Overall Length (mil): 313Overall Length (mm): 7.95
-
Product
Probes & Flow Cells
-
The sample interface is a virtual “windows into the process” and is a critical component of any optical analyzer system. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV/Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal transmission for long-term reliable measurements.
-
Product
Photometric Probes for Illuminance
LPPHOT03… Series
-
The probe LPPHOT03 measures illuminance (lux), defined as the ratio between the luminous flux (lumen) passing through a surface and the surface area (m²). The spectral response curve of a photometric probe is similar to the human eye curve, known as standard photopic curve V(λ). The difference in spectral response between LPPHOT03 and the standard photopic curve V(λ) is calculated by means of the error f’1.
-
Product
HPA-1 General Purpose Probes
General Purpose Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 655Overall Length (mm): 16.64
-
Product
Probes, Clamp-On
EM-6981 | 9 KHz – 110 MHz
-
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
Product
DDR3 MSO Probes
-
The DDR3 DIMM and SO-DIMM Mixed Signal Interposers connect Address, Command and Control signals of a DDR3 bus to the Keysight V-Series Oscilloscopes with the MSO option. These interposers also provide accessibility to DDR3signals for convenient analog probing.
-
Product
Probes, Magnetic Field
EM-6881 | 480 KHz To 30 MHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
-
Product
Gold Probes
4900 Series
-
The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.
-
Product
Test Probes
-
A physical device used to connect electronic test equipment to a device under test (DUT).
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMCSK-04-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Low Voltage Single Ended Probes
-
A low voltage single-ended probe is typically used for measuring high-speed, ground referenced signals up to 12 V. These low voltage probes are the best choice for making measurements on high impedance, high frequency circuit elements which require minimal probe loading. Users should select probes with a low input capacitance specification (~1 pF) to minimize the probe’s loading effect on the circuit. A probe with lower input capacitance will offer higher input impedance at higher frequencies.
-
Product
P2757 General Purpose Probes
General Purpose Probe
Current Rating (Amps): 20Average DC Resistance lower than (mOhm): 10Test Center (mil): 187Test Center (mm): 4.75Full Travel (mil): 230Full Travel (mm): 5.84Recommended Travel (mil): 167Recommended Travel (mm): 4.24Overall Length (mil): 1,210Overall Length (mm): 30.73Overall Length Remark: Tip 2C: 1140 mil (28.96 mm) Tip 1W: 1205 mil (30.61 mm) Tip 2W: 1205 mil (30.61 mm)
-
-
-
Product
Ultrasonic Probes And Cables
-
The cable connects the main body of ultrasound diagnostic equipment and the probe used for echographic investigation.
-
Product
Transmission Probes
-
Transmission dip probes are used for on-line and inline absorbance measurements in fluids. When dipping or permanently mounting the probe end into the fluid, absorbance can be measured. Discover our range of various transmission dip probes below
-
Product
Low Voltage Differential Oscilloscope Probes
-
Differential signaling used in high speed serial standards requires very accurate characterization. The industry-leading bandwidth and signal fidelity found in a Tektronix low voltage differential oscilloscope probe ensures that you see every possible detail. Tektronix offers TriMode™ architecture which streamlines measurement acquisition by enabling you to make differential, single-ended, and common mode measurements with a single connection!
-
Product
Temperature Probes
-
Our Temperature Probes are ideal for the Instrumentation, medical, communication, machine builder and HVAC industries.
