Defect
other than specified, imperfection .
-
Product
Pruning Saw Control
-
Creation of a system that allows measuring the geometry of the board in the stream, determining the width of the wane, clean surface, the presence of large defects. Calculate the "net" width of the board and give signals for the movement of the saws to obtain the maximum output of the edged board of the given (standard) dimensions.
-
Product
In-Process Test OTDR
8000i
-
The 8000i In-Process Test OTDR is the most recent addition to Photon Kinetics' family of innovative solutions for optical fiber cable testing. The 8000i's "cable test optimization" provides the balance of OTDR dynamic range and dead zone performance that's proven to be most effective for accurate characterization of typical fiber cable lengths. Dynamic range has been maximized to reduce measurement time, while resolution has been tuned to ensure that typical cabled fiber defects are detected. The 8000i delivers this optimized measurement capability at a more economical price than our full featured, final QC 8000 OTDR, which makes it a perfect fit for "in-process" testing on ribbonizing or loose tube production lines.
-
Product
High-speed In-Line 3D CT Inspection System
X-eye 6300
-
Automatically inspects the defects of products in customer's line with high-speed 3D CT tomography.Able to inspect every defects of Double-sided PCBA & BGA mounted components precisely by solving overlapped X-ray image issue.Inspection speed of 3 sec/1FOV from loading to automatic Good/NG judgement.
-
Product
Partial Discharge Testing Equipment
AR700
-
PD Defect Location in High-Voltage Equipment Insulation by Acoustic Sensors To act on deteriorating insulation the source of PD must be known.The insulation defects produce partial discharges, which emits electrical impulses, radiation of electromagnetic waves as well as acoustic signals.The AR700 measures acoustic signals with multiple sensors spread over the transformer. Then the software determines the failure location using the time difference of all incoming signals. Finally, these coordinates are shown in a 3D model of the transformer. AR700 device is used for measuring of acoustic signals on the external surfaces of gas-insulated breakers and substations, power transformers and other tank high-voltage equipment. The acoustic signals are caused by partial discharges in the insulation, which is the sigh of the defects.The advantage of “AR700” device is the quick installation of the acoustic PD sensors on the external surface of high-voltage equipment tank. The sensors have magnetic holder that is why there is no need to de-energize the equipment for the sensors installation. “AR700” device has 4 syn-chronic channels for acoustic signal measurement. This gives the possibility not only to find the defects in the insulation, but also to locate them. The location function of the “AR700”device is unique for acoustic devices.
-
Product
3D Sensor (Shiny Surfaces)
reflectCONTROL
-
reflectCONTROL is designed specifically to meet the high quality requirements that ensure high quality for shiny surfaces. The system based on deflectometry projects a striped pattern onto the measurement object. Defects on the surface cause deviations from the striped pattern which are recorded by cameras and evaluated by software.
-
-
Product
Permanent Monitoring
-
Real-time Ultrasound and Vibration data indicate changes in healthy function earlier in the P-F Curve than other condition monitoring technologies. Advanced warning allows every maintenance job to be planned while reducing levels of critical spares held in inventory. Reliability teams benefit from a proactive culture that affords them time to eliminate defects rather than simply applying band-aids.
-
Product
Lab Inspection & Testing Services
-
Our lab services use advanced techniques to thoroughly inspect components for manufacturing flaws before assembly. We work with clients in the aerospace, automotive, oil & gas, manufacturing, wind energy, and various other industries to ensure their materials and components are free from defects that were introduced in forging or manufacturing processes.
-
Product
Electroluminescence Test Systems
-
The products of the SolarModule EL-inline family are integrated into a module production line, before lamination, after lamination or at the end directly after the performance measurement. High-resolution cameras provide excellent image quality and allow the automatic detection of relevant defects. A manual evaluation of images is no longer necessary, which means that considerable costs can be saved. Communication to upstream and downstream processes is flexible and can be adapted to all common interfaces.
-
Product
Package Leak Detectors
-
Packages should be absolutely leak tight. However, even with the utmost care in the process, faulty packaged products cannot be completely avoided. Defects in the sealing process or in the material can easily lead to leaks, sometimes microscopically small.
-
Product
Inspection System for Die Casting
X-eye 7000BS
-
Appropriate for medium•large size component inspection and detecting surface structure and defects(inside voids and cracks etc).Due to high-energy, high-power Micro-focus X-ray Open Tube, maintenance cost's reduced significantly and enables long-term use with only replacing consumables.Customization is available with selecting main parts by customers depends on their needs for size and material.
-
Product
Software For Visualizing Surface Quality
STATOVISION
-
Foerster Instruments, Incorporated
In combination with a STATOGRAPH module, the STATOVISION software enables the visualization of eddy current signals in a clearly arranged C-Scan. This results in an image of the surface quality of the components, allowing surface defects to be precisely localized. A major advantage of the STATOVISION software is the pattern recognition, which can be used for surpressing drill holes on brake discs, for example. The documentation of the entire scan is used for continuous quality assurance.
-
Product
Ultrasonic Optical Flaw Detector
MIV-X
-
Thanks to Shimadzu’s proprietary light imagining technique, which combines an ultrasonic oscillator with a stroboscope, defects near the surface of a material, including peeling of the bonding and adhesive surfaces of heterogeneous materials, as well as paint, thermal sprays, and coatings can be inspected easily and non-destructively.
-
Product
Vision Metrology System
NGS 3500Z
-
This bench top lower cost, yet high performance system is designed for applications where defect detection and precisionmeasurements on wafers and other parts (up to 200 mm) are required. It is well suited for use as a dedicated productiontool or as a versatile process development system. It features a powerful set of automated as well as semi-automaticoptical/ video tools optimized for high accuracy, production throughput, and ease of use.This automated and versatile platform features a standard Nikon/ Olympus bright/ dark field microscope with optionalNomarski, and precise part staging. This system offers significant and unique advantages for dual production/ engineeringuse, and provides the perfect solution when both defect detection and dimensional metrology are required.
-
Product
Security Testing Services
-
You're building more-complex software faster than ever before, but does your team have sufficient application security skills and resources to test it for security defects? Synopsys security testing services provide continuous access to security testing experts with the skills, tools, and discipline needed to cost-effectively analyze any application, at any depth, at any time.
-
Product
Winding Resistance Tester
JYR20S/10S
-
DC winding resistance testing is regarded as another essential routine screening tool. It indicates problems such as loose, defective or incorrect connections, which cause enough transformer failures each year to be regarded as a failure category of its own.
-
Product
Precision Continuous Flow Metering + Dispense System
Graco Dispense Analyzer
-
A whole new level of precision for drivetrain gasketing. Detect air bubbles and defects you couldn't see before. Track critical measurements, including entrapped air. Quickly and easily find a defect's root cause. Avoid expensive problems by responding sooner. Save millions: Contain warranty claims and recalls. The Graco PCF and Analyzer combination: Your ultimate system for accurate, reliable dispensing. The new Graco Dispense Analyzer is a monitoring system capable of detecting the tiniest air bubble or error during adhesive dispensing. Paired with the Graco Precision Continuous Flow (PCF) system, the Analyzer monitors your dispense in real time, detecting immediately if conditions are off and may potentially compromise your final product. With the ability to respond immediately, you can avoid defects that lead to costly recalls. The Analyzer stores the signature of each dispense, giving you the ability to replay the data, even months or years after the actual dispense. Seeing the data replayed as if in real time, you can more easily pinpoint the root cause of the defect and contain a recall or warranty claim to only those products that were affected.
-
Product
RFID Label Inspection System
Eurotech RFID FS
-
The Eurotech RFID FS RFID accurately rewinds rolls of RFID labels and validates their receptivity by running them through the Voyantic Tagsurance RFID inspection system. The unit allows stopping at a predetermined editing spot for the removal and replacement of the defective piece, as well as indicating defective labels by a mark printed by an inkjet system integrated with the machine. Adjustment of the closed loop tension control system can be made through adjusting the parameters on the software that control the servo motor control system. This gives the customer a virtual infinite range with which to wind their labels without cracking the inlay or antenna. As well accurate web adjustment and guidance is provided with a web guide system complete with an ultrasonic sensor. The Eurotech RFID FS RFID label inspection system is equipped with the Voyantic Tagsurance for testing the performance of RFID tags. This is done by verifying that the tag responds to commands on its whole operational frequency range, which means testing the tag on multiple frequencies, also outside the RFID reader frequency. Accurate power output combined with the Voyantic Snoop Pro antenna, optimized for testing tags inline at high speed, allows defining precise acceptance criteria and achieving stable quality.
-
Product
Ultrasonic Testing
Pundit 250 Array
-
The Pundit 250 Array brings a quantum leap in the ultrasonic pulse echo testing. A number of unique innovations make the Ultrasonic multi-channel instrument the best and fastest solution for thickness measurements, detecting defects and localizing objects which cannot be easily detected by any other technology. This includes the assessment of thick concrete elements such as tunnel linings as well as pipes and tendon ducts beyond the rebar layer.
-
Product
Nano-focus X-ray Inspection System
X-eye NF120
-
Nano-focus Tube of 400 nano resolution is installed which is specialized for Semiconductor Packaging, Wafer Level Packaging(WLP) requiring detection of Sub-micron defects.Able to trace and inspect defected area precisely by precise movement of axis with Anti-vibration table.Tomography is available if 3D CT module is added and Wafer Bump Automatic Inspection is available from loading to inspection with wafer handler systems.
-
Product
SDT Checker Range
-
With a focused solution for every problem, the Checker range makes ultrasound available to everyone. Choose the right tool for the right job and perform fast troubleshooting inspections. As a first defense against breakdown, Checkers identify defects quick and early, allowing for deeper analysis and trending with an SDT200, SDT270 or SDT340.
-
Product
Chip Inspection System
GEN3000T
-
GEN3000T is an inspection system that performs automatic inspection of individual semiconductor chips.This revolutionary chip surface inspection system was achieved by combining the chip handling technology cultivated by Toray with the inspection algorithm used in the "INSPECTRA®" wafer defect inspection system.
-
Product
Making Invisible Visible
Quadra 3
-
Quadra™ 3 is your partner for high quality X-ray inspection for production line quality control. Detect a wide range of manufacturing defects including BGA, QFN and IGBT attachment, PTH filling, interfacial voiding, component cracking and counterfeit device screening. High quality, high magnification inspection for product applications.
-
Product
Reticle Manufacturing
-
An error-free reticle (also known as a photomask or mask) represents a critical element in achieving high semiconductor device yields, since reticle defects or pattern placement errors can be replicated in many die on production wafers. Reticles are built upon blanks: substrates of quartz deposited with absorber films. KLA’s portfolio of reticle inspection, metrology and data analytics systems help blank, reticle and IC manufacturers identify reticle defects and pattern placement errors, thereby reducing yield risk.
-
Product
Bushing Monitoring
-
Qualitrol Bushing Monitor System is an on-line Tanδ (PF) and Capacitance monitoring system for substation bushings. It measures the phase difference induced by capacitive layers of bushings and calculates the rate of change to predict defects in bushing insulation.
-
Product
Rotational Metrology System
-
The ZeroTouch® Rotational Metrology System is a precise, high-speed, in-line or near-line metrology, and inspection system that measures critical dimensions of rotors, stators, brake discs, and other cylindrical parts, providing manufacturers with real-time metrology, and inspection data to optimize production processes, detect defects, and improve ROI.
-
Product
Magnetic Particle Inspection
-
Is an inspection method used to identify defects on the surface of ferromagnetic materials by running a magnetic current through it.
-
Product
Flat Panel Display Test Solutions
-
Support 8K SHV (Super Hi-Vision 7680x4320 / 8192x4320)Support full 8K scrolling functionIndependent signal and power module designDual-core graphics processing architecture - Increase graphics and data transmission performance - 8K Super Hi-Vision images switch in less than 200msSupport 6/8/10/12 bits color depth (12 bit only in LUT mode)Support user edited test patterns - BMP pattern format - Maxi. 300 of 8Kx4K bmp patternsSupport VDIM and PWM dimming functionSupport cross coordinates defect positioning functionSupport auto flicker adjustment (with A712306)Support gigabit Ethernet control interfaceSupport USB port for data update
-
Product
Defect Isolation
-
*Traverse through the physical design to trace nets and vias down to the defect location*Utilizes industry standard LEF/DEF design files, scan-based test information, tester fail logs and diagnostic reports to determine and isolate the physical defect location*Enables the user to leverage their diagnostic experience to determine the root cause of the defect*Interactive layout viewer displays scan chains, mapped mismatches of scan cells, layers, nets and subnets with search capabilities(component, net, cell)*Physical XY coordinates are always displayed for components and nets to guide the user through the design to quickly identify suspect sites for FA using techniques like Emission, OBIRCH, LIVA, TIVA, or FIB
-
Product
MicroDetect Basic
MDb-01
-
Hachmann Innovative Elektronik
MicroDetect basic is a handy, exact and simply useable voltage detector and interface-tester. Its automatic, thorough self-test ensures reliable function. The permanently enabled interface-tester warns against defect interfaces.
