-
product
Stylus Profilometry
Dektak®
Bruker's Dektak stylus profilers are the product of over four decades of proprietary technology advances. They provide repeatable, accurate measurements on varied surfaces, from traditional 2D roughness surface characterization and step height measurements to advanced 3D mapping and film stress analyses. Dektak surface profilers have been widely accepted as a superior solution for measuring thin film thickness, stress, and surface roughness and form in applications ranging from educational research verification to semiconductor process control.
-
product
Tactical Grade Inertial Measurement Unit (IMU)
ADIS16490 iSensor
The ADIS16490 iSensor® device is a complete inertial system that includes a triaxial gyroscope and a triaxial accelerometer. Each inertial sensor in the ADIS16490 combines industry-leading iMEMS® technology with signal conditioning that optimizes dynamic performance. The factory calibration characterizes each sensor for sensitivity, bias, alignment, and linear acceleration (gyroscope bias). As a result, each sensor has its own dynamic compensation formulas that provide accurate sensor measurements. The ADIS16490 provides a simple, cost-effective method for integrating accurate, multiaxis inertial sensing into industrial systems, especially when compared with the complexity and investment associated with discrete designs. All necessary motion testing and calibration are part of the production process at the factory, greatly reducing system integration time. Tight orthogonal alignment simplifies inertial frame alignment in navigation systems. The SPI and register structure provide a simple interface for data collection and configuration control.
-
product
AC Power Source
6500 series
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
product
USB Data Communications Multiplexers
These USB multiplexers are ideal for the testing of multiple devices that use USB interfaces, allowing the test system to select one target device from many. The design is bi-directional to permit use as a multiplexer or de-multiplexer with no impact on performance and uses long lifetime electro-mechanical relays characterized for use in data communications systems.
-
product
RF Training Kit And Lab Sheets
Y1800A
The RF transceiver kit consists of a transmitter unit and a receiver unit in superheterodyne architecture. The transceiver units are made up of various RF building-block modules such as filter, low noise amplifier, power amplifier, mixer and oscillator. The RF transceiver kit is controlled by a Windows-based Control Panel software via USB. A Measurement Automation Program is provided to demonstrate automated characterization and test of RF circuits. A signal generator and a spectrum analyzer are required to run this program.
-
product
Amplified Spontaneous Emissions (ASE) Sources
The AP505xA series, high power ASE sources provide stable output power up to + 23dBm and broad flat spectrum over C+L band or T band. They enable effective and efficient measurements for component characterization or optical sensing. Finally, these products are proposed in friendly-user stand alone benchtop instrument with touch sensitive screen, GPIB, ethernet, RS-232 or USB controls.
-
product
Fully Portable Stand-Alone OTDRs
LOR-200
The LOR-200 is a family of fully portable stand-alone OTDRs. The instrument is integrated in a Windows XP based PC-platform with touchscreen interface.The LOR-200 is based on Luciol's novel scanning photon-counting technology (US patent #7,593,098). It achieves a superior dynamic range, and allows high resolution fiber characterization up to a total distance range of 160 km.
-
product
OTDR
Wuhan Sunma Technology Co., Ltd.
OTDR, short for optical time-domain reflectometer, is an optoelectronic instrument used to characterize an optical fiber. It can offer you an overview of the whole system you test and can be used for estimating the fiber length and overall attenuation, including splice and mated-connector losses. It can also be used to locate faults, such as breaks, and to measure optical return loss.
-
product
Zeta Potential & Particle Size Analyzer
AcoustoSizer II
The new AcoustoSizer IIs provides thorough characterization of concentrated colloidal dispersions. Directly measuring particle size, zeta potential, pH, conductivity, and temperature, it furnishes the most comprehensive analysis available in a single, turnkey instrument. Based on a flow-through sensor design, the AcoustoSizer IIs can be used in a laboratory batch analysis mode or connected directly to a process slipstream. Built-in syringe pumps provide automated potentiometric and volumetric titration capabilities for accurate isoelectric point and surfactant addition determination.
-
product
LXI Microwave Matrix, 10GHz, Single 8x4 With Loop-Thru
60-750-184-A
The 60-750-184-A is a single 8x4 10GHz microwave matrix with loop-thru. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 18GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
product
Vevo LAB Suite
Vevo LAB offers basic and advanced tools for visualizing, quantifying and characterizing disease progression.
-
product
7U 14 slot ATCA backplane
109ATCA714-1003R
The 7U 14 slot ATCA backplane is a dual start with radial IPMI, designed to meet 40Gbps (4 x 10G ports) data rates. Elma's ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
product
2-MGEM Optical Anisotropy Factor Measurement System
The 2-MGEM Optical Anisotropy Factor Measurement System is a normal-incidence polarization reflection microscope designed to measure the sample Mueller matrix and is a 2008 R&D 100 Award Winner. This system is designed specifically to evaluate the Optical Anisotropy Factor (OPTAF) of cross sections of TRISO nuclear fuel pyrocarbon layers. Other possible material characterizations include measuring Mueller matrix elements of other crystals, carbon compounds, and thin film coatings (e.g. surfacedeposition films) at normal incidence. The 2-MGEM can also measure retardation (d), circular diattenuation (CD) and the polarization factor (ß). These parameters are not measurable using older techniques, since those techniques do not incorporate a compensating optical element.
-
product
Optical Return Loss (ORL) Meter
OPTOWARE-S300 (FOTS-ORL Meter Systyem)
The Optical Return Loss(ORL) Meter is an efficient system for the characterization and test of optical components and systems to be performed in high quality.
-
product
Wood Moisture Meters
PeakTech Prüf- und Messtechnik GmbH
High quality wood and material moisture meter, which is characterized by its ease of use and universal applicability. The device has an LCD display, in which measured values of humidity and ambient temperature are displayed. In addition, it is equipped with an LED display, which enables a quick good-bad assessment of the measured values. When burning wood in a wood-burning stove with a high moisture content, the efficiency of the stove decreases, while at the same time the emission of pollutants, such as soot and fine dust, increases. In addition, there is a build-up of soot in the chimney, which can lead to a fire. Therefore, this device is ideal for wood storage, control during the heating season or use in construction.
-
product
Refractive Index Profiler
S14
The S14 Refractive Index Profiler complements optical fiber preform analysis measurements by providing highly accurate and precise characterization of the refractive index profile of drawn single-mode, multimode, and specialty fibers using the RNF (Refracted Near Field) technique. The S14 index profile data produces fiber geometry information directly. Manufacturers can also use S14 data for the prediction of fiber transmission parameters such as mode field diameter, cut-off wavelength, and chromatic dispersion.
-
product
LED solar simulators
We offer innovative A + A + A + LED solar simulators for the integration of the production process and for the stand-alone operation in the laboratory or goods receipt. Our LED solar simulators are characterized by maximum repeatability, a long pulse duration and very low maintenance.
-
product
Device Characterization Software with Test Automation
14565B
The Keysight 14565B device characterization software is designed for easy evaluation of portable battery powered device (like 3G handsets, PDA, WLAN, and Bluetooth enable devices) current profiles to ensure long operating life of devices.
-
product
Signal Generator Frequency Extenders
FES
These frequency extension modules easily connect to the output of your signal generator so you have high-performance source for your DUT characterization activities. Characterize your DUT with the confidence that the superior performance in terms of output power, spurious and harmonic will provide product accurate results.
-
product
Power Device Analyzer / Curve Tracer
B1505A
The Keysight B1505A Power Device Analyzer / Curve Tracer is the only single box solution available with the capability to characterize high power devices from the sub-picoamp level up to 10 kV and 1500 A. These capabilities allow evaluation of novel new device such as IGBT and materials such as GaN and SiC. The B1505A supports a variety of modules: high voltage SMU (HVSMU), high current SMU (HCSMU), ultra high current (UHC) module, ultra high voltage (UHV) module and high voltage medium current (HVMC) module. The B1505A also supports: high-power SMU (1 A/200 V), medium-power SMU (100 mA/100 V) ,medium-current SMU (1 A/30V pulsed, 100 mA/30V DC) and a multi-frequency capacitance measurement unit (1 kHz 5 MHz). Its ten-slot modular mainframe allows you to configure the B1505A to suit your measurement needs.
-
product
Materials Test Systems
An impedance analyzer is a device that uses a programmable AC voltage / current source, together with voltage and current measurement circuits, to characterize sample impedance over a wide range of frequency. An example of this being the world famous Solartron Analytical 1260A Impedance Analyzer that provides EIS impedance characterization over more than 12 decades of frequency from uHz to tens of MHz. Impedance Analysis characterization is a key technology that enables new materials development for semiconductors, smart-materials, ferroelectrics, piezo-electrics, solid oxide, solid electrolytes, ceramics, polymers, OLED and many more materials.
-
product
Automated Wafer Prober for Magnetic Devices and Sensors
Hprobe design and fabricate turnkey automated testing equipment (ATE) for electrical characterization and testing of integrated circuits under magnetic field such as MRAM (Magnetic Random Access Memory) and sensors. In each phase of the technology and product development as well as during mass manufacturing, a dedicated magnetic tester is available.
-
product
Manual Tuners
Manual tuners are used both in the laboratory and as system components to establish or transform impedances for a number of applications. They can be used to establish optimum source or load terminations for device characterization, normalize a source or load for precision laboratory measurements and/or calibrations (noise, power, etc.), and can act as a matching transformer between a mismatched source and a mismatched load.
-
product
Power Dividers/Combiners
Macom Technology Solutions Holdings Inc.
MACOM’s power combiners and dividers are used in aerospace and defense, wireless, and wireline communications applications. These devices can also be used for broadband CATV applications. They are available in a variety of connectorized and surface mount packages. Available in subsets operating between the 400 kHz to 26 GHz frequency range, our dividers and combiners are characterized as both 50 and 75 ohm devices
-
product
System Instruments
bsw TestSystems & Consulting AG
Many tasks in the area of semiconductor characterization as well as in the testing of electronic assemblies are routine tasks. Test series of new building elements or samples from production are routinely measured in a large number of electrical parameters. For this, you do not need a measuring device with a complex graphical user interface. A simple interface for remote control with a PC is sufficient. The evaluation and visualization of the results is also carried out on the PC. With the Keysight E5270B and its "little brother" the E5260A two powerful modular SMU units are available for the purpose of the integration into automatic test systems.
-
product
Scratch Tester
Scratch testers from Anton Paar are used to characterize film-substrate systems and to quantify parameters such as adhesive strength and friction force by using a variety of complementary methods. This makes scratch testers invaluable tools for the determination of coating adhesion, scratch resistance, and mar resistance in research, development, and quality control.
-
product
Semiconductor Package Wind Tunnel
WT-100
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
product
General Purpose Single Axis Accelerometers
Motion of a rigid body can be characterized within six degrees of freedom. Providing mechanical excitation to simulate this motion as may be encountered in the real world can entail a variety of test machines. There are various pound/force vibration shakers for structural testing. Regardless of the apparatus, the goal is always to ensure that the product under test can adequately perform, and reliably survive, in the environment in which it will be deployed, or to which it will be exposed during transport. PCB® accelerometers provide the measurement signals needed to control the vibratory input and to analyze the product’s reaction to such testing.
-
product
Syscal Pro
The Syscal Pro is an all-in-one multinode resistivity and induce polarization sounding and profiling system for environmental and engineering geophysical studies. The Syscal Pro gathers a 10 channels receiver and a 250 W internal transmitter which make it the more powerful system of the Syscal range. Compact, easy-to-use and field proof, the Syscal Pro measures both resistivity and chargeability. It is ideal for environmental and civil engineering applications such as depth-to-rock determination, weathered bedrock mapping. With a maximal output voltage of 2000Vpp, the Syscal Pro is very adapted to detect deep fault in fractured aquifers or to characterize the depths and thickness of the groundwater aquifers.
-
product
Soft Front Panel for NI RF Analyzers
NI RFSA Soft Front Panel
The NI RFSA Soft Front Panel helps you quickly view and analyze RF signals using PXI hardware from National Instruments. The soft front panel features built-in measurements such as third-order intercept (TOI), complementary cumulative distribution function (CCDF), adjacent channel power ratio (ACPR), occupied bandwidth (OBW), channel power, and transmit power. With these one-button measurements, you can quickly measure, display, and store results, which makes NI PXI instruments ideal for characterization and validation environments. You can also use the NI RFSG Soft Front Panel for generating continuous waveform (CW) or modulated RF signals.
