Wire
See Also: Contacts, Harness, Connectors
-
Product
Wire Damaged Tester
WDT-1
-
This equipment is designed and manufactured according to corresponding regulation in standard IEC884-1, GB299.1-96, GB16915.1-97 and other electronic accessories relevant standard. Mainly used to test damage degree of fixed connection components lead wire of with thread clamping type and no screw terminals, so as to inspect whether it can withstand mechanical stress during normal use.Specification: • Power supply: AC220V 50Hz • Test rate: 10±2r/min (GB16915.1-97: 12 ±1r/min) • Rotating radius: 100mm • Test distance: 250~500mm adjustable • Test numbers (Number of rotating): 0~999999 any set • Mass: 0.3KG, 0.4KG, 0.7KG, 0.9KG, 1.4KG, and 2.0KG (GB16915.1-97: 30N, 40N, 50N, 60N each of 2 pcs) • Stations: 2 • Dimension: 1200×1400×400 (mm) • Remarks: The mass and rotating radius can be optional as per customer requirements.
-
Product
Wire Abrasion Tester
SG-D03DG
-
This machine is mainly based on UL1581 / UL83 standard abrasion test wire and cable testing requirements .
-
Product
Hot Wire Ignition Tester
-
The HWI test indicates a materials resistance to ignition when exposed to abnormally high temperatures resulting from a component failure such as a conductor carrying far more than its rated current. HWI performance is expressed as the mean number of seconds required to ignite a specimen when wrapped with an energized non-chrome resistive wire that dissipates a specified level of energy.
-
Product
One Wire Communication Board
MS 1727
-
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
Product
Automatic Wire Test Set
AWTS
-
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
Product
Drawing Die And Wire Measurement
DGMS – Die Geometry Measuring System
-
Optik Elektronik Gerätetechnik GmbH
Measuring system for diameter, roundness, reduction angle and bearing length of wire drawing dies.
-
Product
Gauge Type T Thermocouple Wire
W-TW-44TEF
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
Wire Harness Tester
Panther4HT Master- Slave DSU
-
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
Product
Wireless Wire Break Detection System
A909
-
The A909 is a wireless system that allows to detect wire breaks for cabling machines having no sliding contacts brushes.
-
Product
4-Wire Universal Cable Tester
LX-860
-
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface·Starting up conducts self-diagnosis and self-correction·The system can scan and direct automatically.·The system provides advanced instant open-circuit, short-circuit, continuity test, can test the wire break·It can function as unilateral, standard, multi-segment and spot test of wire·The maximum test voltage is AC1000V / DC1500V
-
Product
Wire Sorter
-
Shanghai Beha Electronics Co., Ltd.
*Standard signal transmitter identifies up to 12 lines*Clear indication of short circuits, open circuits, or interruptions*Integrated continuity tester
-
Product
Glow Wire Tester
TF346
-
TESTEX Testing Equipment Systems Ltd.
Glow Wire Tester, to determine the resistance to fire insulating parts. The testing of electro-technical products for fire hazard is conducted by simulating as closely as possible actual effects occurring in practice. Parts of electro-technical equipment which may be exposed to thermal stress due to electric effects & deterioration of which may impair safety of equipment shall not be unduly affected by heat & fire generated within the equipment.
-
Product
Glow Wire Test Apparatus
-
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
Product
High Precision Glow Wire Tester
CX-Z17
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60695-2-1 CX-Z17 High Precision Glow Wire Tester is desinged according to IEC60695-2-1, IEC60695-2-13, UL746A, IEC829, DIN695 and VDE0471 etc. standards.The IEC60695-2-1 CX-Z17 High Precision Glow Wire Tester is suitable for resistance to abnormal heat and fire test on lighting lamps, electronic products and household appliances.
-
Product
Thermocouple & Fine Wire Welder
L60
-
The Thermocouple Welder, manufactured by Labfacility, is a compact, simple-to-use instrument designed for thermocouple and fine wire welding.
-
Product
Vibrating Wire Peripherals
-
Many Campbell Scientific vibrating-wire peripherals enable dataloggers to read vibrating-wire sensors (also known as vibrating-wire or vibrating-strip transducers). These sensors measure strain, load, pressure, and water level, and they output a frequency signal generated by a vibrating filament. Campbell Scientific also offers vibrating-wire dataloggers that read the sensors directly.
-
Product
Advanced Wire Tracers
-
Amprobe’s Advanced Wire Tracers provide accurate results in minutes with new features and technologies that simplify wire tracing and breaker identification, including two optimal frequencies for both energized and de-energized wire and breaker tracing in walls, ceilings, and floors.
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
12-600V AC Adjustable Non-Contact Wire Tracer
5221
-
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 12V~600V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
Product
Wire Crimp Testers
-
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
Product
Wire Crimp Pull Tester (Motorized)
WT3-201M
-
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
Product
L60+ Thermocouple & Fine Wire Welder
-
The Thermocouple Welder, manufactured by Labfacility, is a compact, simple-to-use instrument designed for thermocouple and fine wire welding.
-
Product
PDS Wire Crane Monitoring System
-
It shows a real time overview of the wire crane in navigation, profile, and 3D views; displaying the clamshell, pontoon/vessel, design depths and color-coded digital terrain model (DTM). The navigation view highlights the high and low spots and is updated in real time, registering the progress of the dredging work. The registration follows the shape of the clamshell, bucket or orange peel bucket and is visible immediately in all views. The system also shows the open/close status of the dredge tool. Up/down indicators show the operator the exact distance to the seafloor and design depth continuously. 3D design models allow the use of complex designs.
-
Product
Bulk Wire and Cable
-
Teledyne Marine Cable Solutions
With 50 years of dedicated experience in providing cable and interconnect solutions, Teledyne Cable Solutions meets challenges for application-specific, multi-core cables for harsh environments and complex ruggedized cable assemblies and harnesses.
-
Product
Post Wire and Die Bond Inspection Machine
IV-T3300
-
IV-T3300 is a post wire and die bond inspection machine with Dual JEDEC Tray Feeder System. It features a large inspection area of 600x500mm and a quick trays change of 5-7 seconds.
-
Product
Metal Wire Torsion Testing Machine
WTT Series
-
Jinan Testing Equipment IE Corporation
WTT series metal wire torsion tester is mainly used in a metal factory to test the plasticity of metal wires and ropes under torsion condition. Surface flaws of steel wires may be shown during the testing process. The revolution is displayed on a 4- digit LED, with the max. revolution value displayed as 999.9. The revolution value is automatically held at the break of specimens. With computer & software, the Metal Wire Torsion tester can realize automatic control. The Metal Wire Torsion tester conforms to standard ASTM A938, ISO7800. The Metal Wire Torsion tester is an ideal QC tool for Quality Inspection & Control Department related to steel wire application.
-
Product
Wire Tracer
LKZ-700
-
Wire tracer LKZ-700 is designed for detecting of cables and conductors in various environments (concrete, brick, wood, ground) being under voltege, without the need to disconnect any devices from tested network, as well as in non-voltage environments.
-
Product
Super-Safeway Three Wire Circuit Tester
1301270009
-
Super-Safeway Three Wire Circuit Tester, 3 Indicating Lights & Receptacle Tension Tester in Carrying Case
-
Product
Wire and cable slicer
CX-18
-
Shenzhen Chuangxin Instruments Co., Ltd.
Wire and cable slicing machine is a kind of used products factory la bequipment. Using mechanical transmission feed, blade cutting structure, it can be cut1 to 12 mm range plastic various thickness, sheet material, etc., they are availablRubber, leather material and hardness of the material must be sliced, the machine is widelyUsed in rubber, plastic, leather, electric wire, cable, scientific research units, etc.
