Wire
See Also: Contacts, Harness, Connectors
-
Product
Cable Assembly, 50-Pin SGMC, Female to Unterminated, Cut Ends, 5A, 1m
A050FFR-C-0A100
Cable Assembly
This is a 1m long female to unterminated 50-Pin SGMC cable assembly with ferrules and is constructed from 19/0.18 (21AWG) Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
Personal Computer Aided Antenna Design
PCAAD 7.0
-
Antenna Design Associates, Inc.
PCAAD 7.0 is a Windowscompatible antenna analysis, modeling, and design software package. It contains more than 50 routines treating wire antennas, aperture antennas, microstrip antennas, arrays, transmission lines and waveguides, and more. These routines are integrated into a menudriven, userfriendly system allowing you to quickly evaluate the performance of a wide variety of antenna types. PCAAD 7.0 includes a 120-page printed user manual which describes the use of the software, provides examples for each of the routines, and lists technical references.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Tinned Ends, 1m, 45º
A1604F5-T-0A100
Cable Assembly
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
Cable Assembly 15-Pin D-Type, Male to Female, 1m
40-970-015-1m-MF
Cable Assembly
The 15-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Male screwlocks are provided to secure the connectors to their associated products. The 15-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
6U VPX Single Board Computer
VPX6-195
-
Curtiss-Wright Defense Solutions
Our VPX6-195 6U OpenVPX T2080 Single Board Computer (SBC) combines performance with the advanced I/O capabilities of the NXP's quad-core AltiVec enabled T2080 processor. Designed for SWaP-constrained applications, the VPX6-195 provides two independent processor cores on a single printed wiring board (PWB) with a wide range of standard I/O and each with a XMC mezzanine site to provide twice the processing power.
-
Product
Wire Strippers
-
Thermocouple wire, cable and OMEGACLAD™ wire at strippers. Specialized wire and cables require specialized tools. Make your choice with a range of diameters and gauges.
-
Product
AC DC Withstand Voltage & Insulation Tester (HI-POT)
SS71XX series
-
High voltage withstand and insulation tester (HI-POT tester) is used for testing insulation grade and withstanding voltage capability of electrical equipment, transformers, motor, relays, cables, electronic components, electronic applications, inductors, ignition coils, insulation wires, insulation tapes, valve coils, reactors, contactors, etc.
-
Product
SH37F-P-4, 37-Pin Female to Pigtail Shielded I/O Cable, 12ft
778620-04
Multifunction Cable
37-Pin D-SUB Female to 37-Pin Bare Wire Female, 12 ft, Pigtail I/O, Shielded Multifunction Cable - The SH37F-P-4 connects compatible CompactRIO modules to accessories or cables with bare wire connectors.
-
Product
CABLE TESTER
MCT-7
-
Whirlwind Music Distributors, Inc.
This diagnostic cable tester has connectors for analyzing almost any type of cable combination. The convenient rotary switch allows testing of each conductor within the cable and can determine the internal wiring configuration. Tests NL4, 5 pin DIN, BNC, XLR, TRS, RCA and 3.5 mm types.
-
Product
Wire Damage Test Device For Pull Testing
IEC60884 FIG11
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG11 Wire damage test device for pull testingThe wire damage test device is a special test instrument designed and manufactured according to the requirements of IEC884 Figure 11, , etc. It is mainly used to judge whether the screw-clamp type terminal is in design and structure.
-
Product
4CH GigE Vision Compact Vision System with 6th Generation Intel® Core™ i7/i5/i3 Processors
EOS-1300
-
ADLINK’s EOS-1300 is a high performance compact vision system equipped with 6th Generation IntelR Core? i7/i5/i3 processors and four independent PoE (power over Ethernet) ports, delivering data transfer rates up to 4.0 Gb/s. EOS-1300’s FPGA based DI/O provides programmable de-bounce filter, on the fly trigger, and user wiring Sink/Source DO and Encoder functions, making it the ideal solution for machine vision applications requiring high computing power and time deterministic solutions with minimal footprint.
-
Product
Glow Wire Tester
-
Shanghai Dean Electrical Co., Ltd
Glow wire tester would stipulate material (Ni80 / Cr20) and the shape of the heating wire (4 mm Φ nichrome wire) in large current heated to test temperature (550 ℃ ~ 960 ℃, after 1 mi to specified pressure (0.95 + / - 0.1 N) vertical burning hot try 30 s, inspect goods and bedding content whether light-off or the burning time to determine the fire risk of electrical and electronic equipment finished product;Determination of ignitability, ignitability temperature (GWIT), ignitability and ignitability index (GWFI) of solid insulation materials and other solid combustible materials is also applicable to the industries of insulation materials, engineering plastics or other solid combustible materials.
-
Product
Safety Light Grids
-
*Type 4 (IEC 61496) safety light curtains at Type 2 pricing*Reliable protection of hazardous areas*Industry standard M12 connection for simple wiring*Versions for the use in high pressure cleaning applications*Versions with active /passive system
-
Product
Probes
Type K
-
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
Product
Gauge Type T Thermocouple Wire
W-TW-44P
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Battery Discharger & Capacity Tester
IDCE-CT
-
Fuzhou Fuguang Electronics Co., Ltd.
Each wireless module can monitor 4 batteries simultaneously comparing with the traditional method that each module only canmonitor 1 battery, the new wiring operation become easier because the quantity of new modules needed is only a quarter of old-fashioned modules.
-
Product
Drill Chuck Grips
-
Metal rods, wires, and plates and electronic components can be tensile tested using drill chuck grips. Electronic components are tested by placing the metal legs of the components in the grips, allowing different shaped components to be tested with the same set of grips.
-
Product
Vertical Hinged Mounting Frame, 9025, 9U
310113320
Mounting Frame
This 9025 Vertical Hinged Mounting Frame allows the 9025 Receiver to hinge down allowing access to instrumentation and wiring. This frame is 9U in height.
-
Product
Back Plane Tester
-
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
Product
TB-2631B , Term Block for NI PXI-2530B 4x32 1W or 4x16 2W Matrix
781688-01
Terminal Block
The TB-2631B provides a PXI front-mounting terminal block to configure the PXI-2530B PXI Multiplexer Switch Module. It provides direct signal wire connections to the screw terminals inside the terminal block.
-
Product
BATTERY PACK AND BMSTEST SYSTEMS
-
DMC's Battery Pack Test Systems facilitate battery design as well as research and development for national laboratories and research institutions. They are deployed in end of line / production test stations for battery packs developed by major automotive manufacturers and their suppliers. DMC's battery pack test systems are designed to evaluate the battery as a complete system and validate a comprehensive range of battery pack functionalities, including:Power performance, Capacity, DCR / Internal ResistanceContactor and safety interlock functionsIsolation / Insulation ResistancesReporting of operating data through external communication interfaces (usually CAN)Cell VoltagesPack / Cell TemperaturesState of ChargeFaults / Diagnostic Trouble Codes (DTCs)Etc.Electrical characteristics / continuity of internal pack wiring / signalsCooling system operation
-
Product
Miniature Digital Panel Meter
CSMS-321
-
Measuring DCA, DCV, Temperature. 1/32 DIN Size ( 48mmX24mm ). Accuracy: +/- 0.1%(DC), +/- 1%(Thermocouple), +/- 0.2%(Pt100). 3 1/2 Digits Display: 1999. Input Max. 2Adc +/- 10%; 300Vdc, T/C type K: 1200J, Pt100:600J. Aux Power 5Vdc +/- 10%; Isolated Aux. Power 5Vdc, 12Vdc, 24Vdc available in option. Easy to wire, screw type terminal. Outside dimensions is 1/32 DIN Standard ( 48 x 24mm ). High stability & low cost.
-
Product
Cable Length Meter
CLM100
-
UEi Test & Measurement Instruments
The CLM100 Digital Cable Length Meter is an excellent tool to measure spooled cable/ wire. This best seller is built solid and supplied with a ruggedized boot for reliable field performance. Currently being utilized by major utility companies, electrical contractors, wholesalers, and installers where quick and accurate inventory management or measurements are needed for job accountability. Simply attach the Kelvin Clips to both ends of the cable and adjust the indicator to the size wire being measured. A temperature compensation circuit ensures accuracy by compensating for the temperature of the wire.
-
Product
4-Pin Power D-Type Female to Unterminated With Tinned Ends
A008PF4-T-6A200
Cable Assembly
The 4-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
Product
REM-11115, 4-Channel, 2-Wire Analog Output Module for Remote I/O
784749-01
Analog Output Module
4-Channel, 2-Wire Analog Output Module for Remote I/O - The REM‑11115 is an analog output module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11115 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. You can use the REM‑11115 for voltage or current output, and it features a 2‑wire spring terminal connection method. The REM‑11115 has selectable output ranges and short-circuit-proof output channels.
-
Product
Elongation Tester
SC-5
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.3-2008Used to test elongation (ductility) of copper wires covered with φ0.100-3.0 mmenamel, silk or other insulation materials and other metal wires with tensile strength ≤2000N;Application of SCM control allows for fast operation and strong anti-interference capacity;Preset elongation of samples with two-digit toggle switch and, when the preset value is reached during test, motor and counter would automatically stop action and display results;The instrument is capable of measuring elongation while also the tensile force and holding the maximum tensile force value during stretching;Clamps are designed according to characteristics of various wires to prevent samples from breaking at clamp jaws, easy to load samples and, after samples are compressed, enamel can be automatically broken;While sample is broken, movable clamp would automatically stop moving, with error between displayed and actual elongation value less than 1%;
-
Product
3-Pin Power D-Type Cable, Female to Unterminated, Ferrules, 1m
A003PF4-F-5A100
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Terminal Block For 34933A And L4433A 4x8 Matrix
34933T
Terminal Block
The Keysight 34933T is a terminal block for the 34933A 4x8 Matrix and the L4433A 4x8 Matrix used for discrete wiring. It supports up to 20 AWG wire size typical for <100 connections or 24 AWG for >100 connections. The following two terminal blocks facilitate wiring connections to the 34933A module and L4433A instrument.
-
Product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Ferrules, 1m
40-972-025-1m-MU
Cable Assembly
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Multi Function Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
Live circuit warning LED:Immediate illumination of a warning lamp if the circuit under test is live Auto Discharge:Allows fast and safe discharge of electrical energy stored in capacitive circuits following testing Integral overload protection on internal continuity and insulation test circuitry Autoranging 500V DC test voltage for insulation tests 200mA short circuit current on continuity ranges Loop and RCD Testing Wiring connection check LED''s:Immediate indication if wiring of circuit under test is correct Overheat Protection:Rapid detection of overheating of internal circuitry,display of warning signal to user and automatic halting of measurement Supply Voltage Indication:Can display supply voltage value in loop impedance mode Low Current Loop Impedance Test:Short duration low test current will prevent tripping of many passive RCDs
