Wire
See Also: Contacts, Harness, Connectors
-
Product
Compact Size Picking Sensor
NA1-PK3
-
Panasonic Industrial Devices Sales Company of America
With an ultra-compact size of 24mm × 70mm × 8mm (W x H x D), the Panasonic NA1-PK3 Series General Purpose Area Sensors can be installed in bins designed to house small parts. Panasonic's unique beam scanning system reduces wiring and installation time while incorporating a mutual interference prevention function that provides correct operation even in multi-stage parts boxes.
-
Product
Slot 0 Module Retainer Block Set, For Discrete Wiring, 1 Position
510109150
Module Retainer
These module retainer blocks are used to attach modules directly to the inner frame of a VXI receiver for discrete wiring. These modules then hinge down with the receiver to provide easy access to wiring.
-
Product
20-Pin GMCT Male Connector, 16A, With Backshell
40-960-020-16A-M
GMCT Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 14 AWG. Also included is the backshell with screwlocks and cable clamp.
-
Product
Digital Frequency Meter
CSF-400
-
Measuring frequency. Accuracy: +/- 0.05%. 4 Digital display: 9999 Input Max. 400Hz/600 V, 30KHz/12V. Aux. Power AC 115/230V +/-15%, 50/60Hz. Isolation Aux. Power 12Vdc, 24Vdc, 48Vdc, 110Vdc available in option. Easy-to-wire, screw type terminal. Outside dimensions is DIN standard (96mm x 48mm) High stability & low cost.
-
Product
RTD Simulator PCI Card 6-Channel PT1000
50-262-102
Simulator
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card can provides a setting resolution of <90mΩ (also available in <8mΩ - PT100) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
PXI RTD Simulator Module, 16 Channel, PT500
40-263-202
Simulator
The 40-263-202 is a 16-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Signal Module, ITA, QuadraPaddle, 480 Position, Fully Loaded For Wire Wrap With Anti-Rotation (610 138 122)
510151127
ITA Module
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based Mass InterConnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Product
ContactLAB Tester
-
The ContactLAB test platform provides fully configurable reader signal emulation for validation of ISO 7816 contact smart cards and Single Wire Protocol (SWP) USIM for NFC enabled mobile handsets.
-
Product
Terminal Block For 34923A Multiplexer
34923T
Terminal Block
The Keysight 34923T is a terminal block for the 34923A 40/80-channel reed multiplexer, used for discrete wiring. It supports up to 20 AWG wire size for up to 100 connections or 24 AWG for 100 connections or more. Two terminal block options facilitate wiring connections to the 34923A module.
-
Product
Photo Detector with Integrated Transimpedance Amplifiers
ADN3010-11
-
Analog Devices optoelectronic amplifiers include a range of germanium photodiodes that, through a proprietary process, have been monolithically integrated with silicon transimpedance amplifiers and limiting amplifiers. This process eliminates the need for bond wires connecting the photodiode to the transimpedance amplifier, which leads to improved performance and greater manufacturing reliability. Our portfolio of products also supports the growing need for optical and electrical interface miniaturization.
-
Product
Stainless Steel High Performance Flow Sensor
2540
-
The Signet 2540 Paddlewheel Flow Sensor offers field-replaceable electronics and transient voltage suppression (TVS) to provide greater immunity to large voltage disturbances (i.e. lightning) sometimes encountered in field wiring. Sensors can be installed in DN40 to DN600 (1 to 24 in.) pipes using the 1 inch NPT or ISO 7/1-R 1.5 threaded process connection. The sensors are also offered in a hot-tap configuration with a bleed valve service without process shutdown in pipes up to DN900 (36 in.). Both styles of sensors must be used in full pipes and can be used in low pressure systems.
-
Product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Ferrules, 1m, HV
40-972-009-1m-FU-HV
Cable Assembly
A range of 9 Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Tool, Locator, QuadraPaddle, ITA
910104140
Locator Tool
Used with Crimp Tool p/n # 910101103 to crimp QuadraPaddle contacts to 22-28 AWG wire.
-
Product
96-Pin 1.27mm Pitch Female Solder Pad Connector With Backshell, Screwlocks
C096SFR-4SP-5A
-
This connector is designed to allow users to discrete wires using solder pad connections to the 96-Pin 1.27mm pitch connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
783863-02
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Advanced Diagnostic Load Cell Tester
LCT-U
-
The Advanced Diagnostic Load Cell Tester Model LCT-U is a stand-alone hand-held device specially designed for fast, comprehensive troubleshooting of strain gauge load cells. The LCT-U can quickly diagnose problems with all common types of load cell available today, including 6-wire load cells (with sense wires).
-
Product
Rope Testers
-
The LMA Signal measures loss of metallic cross-sectional area (LMA) caused by corrosion, abrasion, etc. The LMA Signal is quantitative and can be calibrated. (Typically, a rope must be retired when the LMA exceeds 10%).The WRR Signal measures wire rope roughness (WRR). WRR is defined as the aggregate surface roughness of all wires in a rope. WRR is typically caused by and indicates internal and external corrosion pitting, broken wires and clusters of broken wires. The WRR signal is quantitative, and it is calibrated together with the LMA Signal.The LF Signal can indicate localized flaws (LF), for example, broken wires, corrosion pitting, etc. Because it is only qualitative - and cannot be calibrated - it is of limited value for assessing rope deterioration and for making rope retirement decisions.
-
Product
20-Pin GMCT Cable, Female to Unterminated, Tinned Ends, 16A, 1m
A020GFR-T-1B100
Cable Assembly
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Bench/System/ATE Programmable DC Power Supply Single Or Dual Outputs, 360 To 840 Watts, With Or Without Remote Interfaces
CPX Series
-
PowerFlex design gives variable voltage and current combinations within a maximum power rangeUp to 60 volts and up to 20 amps180 watts or 420 watts maximum per outputIsolated outputs can be wired in series or parallelConstant voltage or constant current operationSettings Locking (S-Lock)PowerFlex or fixed-range operationVariable OVP tripsSelectable remote sense terminalsCompact quarter or half rack 3U case sizeIsolated analogue remote control (CPX400SA only)RS232, USB & LXI compliant LAN (P models only)GPIB Option (P models only)
-
Product
Plug & Play JTAG/SWD Microcontroller Debugger with Built In GDB Server & UART
Black Magic Probe V2.3
-
In most cases Black Magic Debug takes the form of a firmware for the Black Magic Probe hardware, and implements a GNU DeBugger (GDB) server.The Black Magic GDB server features: - Automatic target detection- No need for target specific configuration scripts- All protocol and target specific control is done through GDB monitor commands- No “software in the middle” like OpenOCD required- Easily scriptable thanks to the GDB scripting capabilities- Interface to the host computer is a standard USB CDC ACM device (virtual serial port), which does not require special drivers on Linux or OS X.- Targets ARM Cortex-M and Cortex-A based microcontrollers- Provides full debugging functionality, including: watchpoints, flash memory breakpoints, memory and register examination, flash memory programming, etc.- [Semihosting / Host IO support] as well as [Serial Wire Debug TRACESWO support].- Implements USB DFU class for easy firmware upgrade as updates become available.- Works with Windows, Linux and Mac environments.
-
Product
MS-M 26-Pin RF Cable Assembly 0.5m
40-979-526-0.5m-FU
RF Cable Assembly
The MS-M RF 26-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
Product
NI-9226, 8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module
785189-01
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module - The NI‑9226 is a resistance temperature detector (RTD) input module. You can configure the NI‑9226 for two sample rate modes: high sample rate or high resolution. The NI‑9226 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per-channel current excitation. The NI‑9226 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Bench-Top Wire Crimp Pull-Force Tester
PT-1500
-
PT-1500 Bench-Top Wire Crimp Pull-Force Tester, Manual Lever-operated for 5.84mm 8-30 AWG
-
Product
Power Distributor
AV-P3040
-
"AV-P3040" can supply 40A (20A x 2). The power supply can be wired directly from the distribution board and equipped with two 20A breakers.
-
Product
CO2 Concentration and Temperature Transmitter
T8448
-
CO2 concentration and temperature transmitter with serial RS485 output is specially designed for use in exacting interiors in building energy management and HVAC systems. It designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets. Large dual line LCD is possible to switch off. Computerized design ensures long term stability and fail indication. Transmitter is designed for use in non-aggressive environment.
-
Product
Electrical Heat Shrink Tubing Solutions
-
TE Connectivity produces Raychem Electrical heat shrink tubing that sets extremely high standards in areas such as insulation, protection, and element proofing. Raychem shrink tubing uses a duplication process that involves a cross-linked material design ensuring cable system's performance. This cross-linked design creates an impenetrable barrier from the elements while simultaneously binding cables and insulating them. The heat shrink process involves tubing that utilizes a thermal influence that causes it to tightly shrink and adhere to a cable. This tight seal is not only ultra-protective, but also flexible, abrasion resistant, and easy to use. This flexible tubing can fit a huge range of cable sizes and specifications. Perfect for various different operations and industrial applications. This includes cables, wires, and even joints.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 0.5m HV, Exit Away From Pin 1
40-970-050-0.5m-FF-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m
A050DF5-C-0A050
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Fence Vibration Sensor
ENVIROMUX-FENCE1
-
Detects when individuals climb over or cut through chain link or wire mesh fences. Advanced built-in signal processor prevents false alarms. Four sensitivity settings to tune each sensor to a particular fence section and intrusion type. Two open-collector outputs – alarm and power failure. UV resistant case and epoxy sealed electronics provides maximum resistance to harsh environments. Rated NEMA 4X and UL94 5V. Use individually or chain units with each ranging from 40 to 60 feet away. Includes mounting brackets for installing the sensor to fence fabric. Screw terminals. Operating temperature: -4 to 131°F (-20 to 55°C). Operating voltage: 9-15V DC.
-
Product
Miscellaneous Test Instruments
-
*Measures cable sag, height and clearance of overhead conductors via ultrasonic signal*Alternative to telescopic measuring poles*No physical connection to cables or wires required*Simple, three-button operation ensures fast, effective measurements
