Wire
See Also: Contacts, Harness, Connectors
-
Product
PCB Adapters - QuadraPaddle
-
QuadraPaddle signal technology adapted to a PCB with a variety of standard connector options. Allows for easy PCB integration with an interface while also offering wiring convenience. Offers "plug and play" functionality between module and instrumentation.
-
Product
Acute High Voltage Differential Probe, 50x/500x, 25MHz, 3500V
ADP5025
-
*USB Powered (or Power Bank)*Bandwidth up to 25 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation
-
Product
Other Switching Power Supplies
-
PeakTech Prüf- und Messtechnik GmbH
The switching power supply technology used ensures high performance with a small size and low weight. 6 different DC output voltages (3 V / 4.5 V / 6 V / 7.5 V / 9 V and 12 V) can be set using a slider. With the 4 mm pole terminals, you can easily connect single wires but also 4 mm banana plugs. The power cord with an Euro plug is firmly connected to the power supply unit, whereby the device is switched off and on via a rear power switch. This handy power supply fits on every work bench and can be used universally in the hobby area, service or training.
-
Product
Wire Rope Detector
-
It adopts the method of magnetic flux leakage and magnetic flux, and uses the Ethernet high-speed transmission method, which can accurately complete the non-destructive testing of the wire rope in service.
-
Product
Solid-State High Power Amplifier 18 - 26.5 GHz
AMP4065LC-2
-
Exodus Advanced Communications
Designed for EMI/RFI, lab, and general communication applications. Exodus Broadband SSPA product feature GaN, GaAsFET discrete and Chip & Wire Hybrid technologies covering one octave through decades frequency ranges from Operating Frequency Range 18.0-26.5 GHz.
-
Product
Automatic Upset Testing Machine
YQA Series
-
Jinan Testing Equipment IE Corporation
This kind of machine is designed according to the International standards EN 10263-1:2001 “Metallic materials upset test methods”, especially for the quality inspection of high-speed rods and wires. Through simulating the quick press conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. This kind of machine is widely used in the steel industry, standard samples manufacturing industry, and tools manufacturing industry, for the inspection of the metallic materials upset tests. Under the room temperature or the hot conditions, exert test force on the direction of specimen axial line, quickly compress the specimen, and then inspect the metal ability of bearing upset deformation in the specified upset ratio. It also can show the metal surface disfigurements.
-
Product
PXI-4070, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter
778274-01
Digital Multimeter
6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter - The PXI‑4070 is a high-performance 6½‑digit, 300 V DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PXI‑4070 … delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXI‑4070 can acquire waveforms at sample rates up to 1.8 MS/s.
-
Product
Temperature Probes
-
Lake Shore offers a variety of temperature sensors in packages that enable mounting in very tight areas. But for some applications (especially if the sensors have to be immersed in liquid), you need to do more to protect the sensor circuitry. For these applications, a cryogenic temperature probe is the optimum choice. Encased in one of these stainless steel thermowell fixtures, the sensor can perform as designed, is unaffected by high pressure, and is sealed to keep electrical components and wiring protected from fluids and other elements.
-
Product
MS-M 26-Pin RF Cable to SMB, 0.5m
40-979-526-0.5m-SMB
RF Cable Assembly
The MS-M RF 26-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Cut Ends, 0.5m, 45º
A1604F5-C-0A050
Cable Assembly
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
Mini Lan Cable Tester
MT-7058
-
Complies with CE safety standardAutomatically detect good connections, opens, crossed wires & split pairsTest RJ45 TIA568A/B (AT&T) 258A), 10 Base-T, Token ring, RJ-11/RJ-12 USOC and coaxial BNC cablePin to pin cable map indicatorNon-contact voltage detection for user safetyTraces wires with tone & remote lights allows one person operationCompact size and lightweight design for easy to carry aroundCircuit Protection for both units to ensure the testing qualityLow power consumption with auto power off function to preserve batteryLong cable test more than 300 meters
-
Product
PXI 2 Pole 18 way Mux with 2 Pole 18 way sen
40-658-002
Multiplexer Module
This PXI multiplexer combines a 2-pole 18-way power distribution MUX with a second lower power 2-pole 18-way MUX in one convenient single slot PXI module.The module is ideal for power distribution where power and sense signals are required to be connected to an array of devices under test. This multiplexer is also convenient for making 4 wire low resistance measurements by supplying the resistor under test with high current through the power MUX and sensing the voltage drop through the sense MUX.
-
Product
Gauge Type T Thermocouple Wire
W-TW-24
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Wire Gauge Calculator
-
Calculate The Optimal Wire Gauge for Your DC Microgrid or Distributed Switch
-
Product
Phasing Sticks
-
High voltage phasing rods enable phase comparisons to be made at the point of paralleling two circuits without the interposition of voltage transformers or secondary wiring circuits.
-
Product
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" Depth
410112702
Enclosure
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" DepthIncludes hinged cover and 4 cable clamps for discrete wiring that provide secure strain relief. With cable clamps in open position- stiffener bar may be removed to allow installation or removal of cables without requiring wiring to be disconnected from the assembly.Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Cut Ends, 2m, 90º
A1604FT-C-0A200
Cable Assembly
For applications where a 90 degree down cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
20-Pin Scorpion Cable Assembly, Male to Female, 30A, 0.5m
A020AMR-020AFR-3A050
Cable Assembly
This is a 0.5m long male to female 20-Pin Scorpion cable assembly constructed from 37/0.4 (10AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
Cable Testers
DMX ADAPTER
-
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
Product
EPIC SBC With AMD G-Series APU, AMD A50M FCH, Dual DisplayPort/VGA/LVDS, Dual LANs And Audio
EP100
-
The EP100 EPIC board, supporting either the AMD G-Series APU dual core T56N with Radeon™ HD 6320 graphics or AMD G-Series APU single core T40R with Radeon™ HD 6250 graphics, combined with the AMD A50M FCH, is ideal for graphics-intensive applications such as high-end medical imaging, digital signage, kiosks/POI, thin clients, and gaming machines. The onboard SO-DIMM socket supports maximum up to 4 GB of DDR3 1333 memory. Integrated AMD HD graphics with DirectX 11 technology, the small foot print embedded board offers stunning 3D visual effects and dynamic interactivity. The EP100 comes with three display outputs with two combinations: two DisplayPort and one VGA or one DisplayPort plus a VGA and 18/24-bit single/dual channel LVDS. Additionally, it provides dual gigabit LAN ports for high-speed wired communication and two PCI Express Mini card expansion interfaces, one with SIM slot, for seamless wireless communication (WiFi + 3/4G).
-
Product
synchro or resolver to digital (BCD) converters
AIT
Digital / Synchro Converter
Computer Conversions Corporation
The TSb series are miniature, high performance continuous tracking synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
Product
uSD Logger Shield
IFB-11001
-
This micro SD logger shield enables time-stamped logging of any signals measured by your Arduino project! Whether sensor shields, breakout boards or datalink connections, this shield will get your logger project up and running quickly. We've included an MCP79410 Real-Time-Clock module for flexible supply voltage timekeeping, which includes an on-board battery holder for a CR1220 battery (included, and is installed). In addition, the micro SD card is interfaced through a high-speed translator IC and supplied with a high-current LDO to meet the demands of the SD standard. Each pin of the Arduino has an offset pin attached for easy wiring to the massive 13x9 pin prototyping area, including the pins connected to the ICSP header! Whether you're using a Mega, Due or Uno, this board has your interfacing needs covered! Finally, the micro SD holder is a push to lock, push to unlock type, which makes it really easy to both install and uninstall your card.
-
Product
Internal Communications Platform
Messenger
-
Using Messenger from Trilogy, you can build a cost effective intercom solution without the installation, operational and future expansion constraints of more traditional 2 and 4 wire systems. From the factory configured Base System, Messenger evolves to suit the emerging communication needs of your organisation.
-
Product
MS-M Style 3-Pin RF Cable, Female To SMB, 2m, RG178 Cable
40-979-503-2m-SMB
RF Cable Assembly
This 2m long MS-M style RF 3-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M style connector to the associated product.
-
Product
PXI-2576, 64‐Channel, 2-Wire, Multibank PXI Multiplexer Switch Module
778572-76
Multiplexer Module
64‐Channel, 2-Wire, Multibank PXI Multiplexer Switch Module —The PXI‑2576 is a multibank PXI multiplexer switch module with 16 banks of 4x1 2‑wire multiplexers. With the flexible architecture of the PXI‐2576, you can configure it in a variety of topologies that make it suitable for parallel measurement operations requiring low‐channel counts, or you can combine all multiplexer banks to form a single high‐channel‐count multiplexer featuring 64 2‑wire channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
Helical Antennas
-
Is an antenna consisting of one or more conducting wires wound in the form of a helix.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 2m, Exit Towards Pin 1
A050DM5-050DF5-0A200
Cable Assembly
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Wire Crimp Pull Tester (Manual)
WT3-201
-
The WT3-201 wire crimp pull tester is designed to measure the pull-off force of crimped wire and tube terminations. An ergonomic lever allows for easy application of up to 200 lbF (1,000 N) of crimp pull force. Adjustable wire terminal grip contains multiple slots for wire diameters up to AWG 3 (0.25 in [6.3 mm]). The tester accommodates most insulation types. Samples can be sent to Mark-10 for evaluation prior to purchase.
-
Product
Light-Guided Connector Assembly | Cable & Harness Tester
CableEye Light Director System
-
Our Light Director™ system (patented) provides a computer-guided technique for assembling connectors used in aerospace, medical, and other high-reliability applications. This system uses light fibers driven by super-bright LED lamps to individually illuminate target cavities in the connector being assembled. When the technician enters the wire code printed on unconnected wires, or touches a wire connected at the other end, the CableEye software turns on the appropriate fiber, thereby causing a bright, flashing light to project from inside the target cavity guiding the technician to the proper insertion point. Correct insertion is confirmed by the elimination of light from that location, whereas insertion into an incorrect location leaves the flashing light visible.
-
Product
Time-Domain Reflectometer
TDR-410
-
*Location damaged power cables.*Fault location copper telecom cables.*Coaxial cable fault location.*Fault location wiring infrastructure.*Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.*Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
