Product

Precise Measurement of Airborne Noise Insulation

Isokell

-

Autoneum Holding AG

Isokell - Autoneum Holding AG

Isokell offers a flexible method geared specifically to the needs of the automotive industry for measuring airborne noise insulation and the transmission loss of vehicle components. The system is easier to use and less costly than traditional acoustic measurement systems.

Product

Ultra Low Noise Preamp

J2180A

-

PICOTEST Corp.

J2180A - PICOTEST Corp.

The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.

Product

Vibration / Shock / Noise & Thermal Control

-

EverythingPCB

EverythingPCB

We specialise in vibration damping and shock isolation solutions for electronics and other light load applications.Our soft gel vibration damping materials are designed for isolating very light componets and extreme temperature environments.Most of our products are held in stock to support engineers with urgent vibration damping, noise control, shock isolation and cushioning impact problems.Our shock and vibration solutions are currently in use in aerospace, rail, truck, bus and handheld applications.

Product

V-Band Low Noise Amplifier 50 to 75 GHz, 35 dB Gain, 5 dB NF

SBL- 5037533550-1515-E1

-

ERAVANT

SBL- 5037533550-1515-E1 - ERAVANT

50 to 75 GHz, 35 dB Gain, 5 dB Noise Figure V Band Low Noise Amplifier for IEEE 802.11.ad WiGig. Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC/150 mA. The mechanical configuration offers an in-line structure with WR-15 waveguides and UG-385/U flanges.

Product

Low Noise Prepolarized Microphone

378A04

-

PCB Piezotronics, Inc.

378A04 - PCB Piezotronics, Inc.

The 378A04 is a matched system that is comprised of a high sensitivity microphone and a low noise preamplifier that contains a built-in filter that enables the free-field response to remain flat over a wide frequency range. The system requires a minimum of 4 mA and measures to 6.5 dBA (5.5 dBA typical) within a cost efficient, prepolarized (0V) design. PCB's model 378A04, the industry's first prepolarized low noise microphone and preamplifier system allows you to measure extremely low amplitudes. In the past this was only possible with externally polarized solutions. With a typical noise floor of 5.5dBA, this microphone system delivers all of the benefits commonly associated with prepolarized systems.

Product

Noise Legislation Assessment Kit - Sound Meter And Dosemeter

05NK006

-

Castle Group Ltd.

05NK006 - Castle Group Ltd.

This system provides you with everything you need for noise risk assessments for noise legislation in one small package. A sound meter, dosemeter and calibrator kit featuring projected daily noise exposure from one short measurement and true peak for monitoring peak action levels.

Product

Noise Monitoring Station

HD2011NMT

-

Senseca

HD2011NMT - Senseca

HD2011NMT is a remote control Noise Monitoring Station with meteo parameters acquisition. It is designed to be part of a network of noise monitoring terminals or a stand alone unit.

Product

Ultra-low Noise High Voltage Amplifier

WMA-200

-

Falco Systems

WMA-200 - Falco Systems

The Falco Systems WMA-200 model is a high quality, high voltage, linear laboratory amplifier optimized for experiments requiring world-class, ultra-low output noise. The excellent noise performance, combined with the wide bandwidth and large voltage range make this amplifier the preferred choice for the most demanding precision positioning systems. The amplifier will routinely enable sub-atomic positioning resolution with piezo positioning systems and MEMS devices. Two WMA-200 amplifiers and a WMA-IB-LN phase inverter - buffer can be used to double the output voltage.

Product

Hi-Q W-Band Ultra Low Phase Noise Analyzer

OE8000W

-

OEwaves, Inc

OE8000W - OEwaves, Inc

HI-Q® W-Band phase noise test system utilizesmicrowave photonics techniques for automatedmeasurement of ultra-low phase noise W-bandoscillators.

Product

Low Noise High Precision High Voltage Amplifier

WMA-280

-

Falco Systems

WMA-280 - Falco Systems

The WMA-280 is a high voltage, low noise precision amplifier. Its specifications have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-280 can be used for MEMS actuation, EO-modulators, as high voltage driver for PZT (piezo) positioners, ultrasonics, and many other applications. Its output noise is only 300 microVolt rms.

Product

Phase Noise Analyzers

-

Holzworth Instrumentation, Inc.

Holzworth Instrumentation, Inc.

Holzworth's Real Time Phase Noise Analyzers are each designed to provide data faster than any other system, while maintaining data accuracy and repeatibilty. There is no guess work as to whether results are valid to the DUT or if there are unwanted variations or contributions coming from the measurement system itself.

Product

High Density, Low Noise, Floating Low Voltage Power Supply System

PL500 Series

-

W-IE-NE-R, Plein & Baus GmbH

PL500 Series - W-IE-NE-R, Plein & Baus GmbH

The WIENER PL500 is a high density, low noise, floating low voltage power supply system. The PL500-Series has been designed  to power lowest noise electronics with medium to high currents (10A to 500A current/channel range) over long distances in voltage or current controlled mode. Operating in either un-sensed or sensed mode the dynamic behavior can be set internally or by software for short, medium or long distances.

Product

Broadband Coaxial Noise Sources

-

Mercury Systems, Inc.

Mercury Systems, Inc.

Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.

Product

Low Noise Amplifier

-

COMM-connect

COMM-connect

The COMM-connect Low Noise Amplifier can be used to amplify signals in a wide range of bands. The amplifier comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.

Product

Low Noise Triple Band Voltage Controlled Oscillator

-

Teledyne RF & Microwave

Teledyne RF & Microwave

This Low Noise Triple Band Voltage Controlled Oscillator was designed to meet a specific customer requirement. The VCO cover the 3300 to 4700 MHz frequency range in three bands. The output power is +9 to +12 dBm with an integrated buffer amplifier to minimize load pulling. The three bands are selected using standard TTL control.

Product

Low Noise Op Amplifiers (≤ 10nV/√Hz)

-

Analog Devices Inc.

Analog Devices Inc.

Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.

Product

Laser-Pumped White Light Source

LS-WL1

-

lightsource.tech GmbH

LS-WL1 - lightsource.tech GmbH

Our LS-WL1 is a laser-pumped white light source with a light output of up to 440 mW from a 600-µm fiber and a wavelength range of 450 – 700 nm, designed especially for professional requirements for extremely high luminance.

Product

Low Noise Amplifiers

-

Macom Technology Solutions Holdings Inc.

Macom Technology Solutions Holdings Inc.

MACOM low noise amplifier MMICs cover a frequencies from DC to 86 GHz operation for a wide range of applications, including network infrastructure, radar and communication systems. MACOMs portfolio of low noise amplifiers offer a broad array of noise figures, input IP3, and input power in bare die and a variety of package types. Offerings include wideband distributed topologies and self or actively biased configurations tailored to system design needs.

Product

White Box Testing

-

Precise Testing Solution

Precise Testing Solution

Does your application have legacy code and your software code messy? If the answer to the above questions is ‘Yes’, your application will fail to perform as expected. Under such cases, you need to optimize the internal structure of your application so that it performs well. To test for the errors in the internal structure opt for white-box testing.

Product

General Noise & Vibration

-

OROS sa

OROS sa

NVGate, the software platform is the cornerstone for all measurement tasks. It hosts the suite of OROS software modules. Whatever the application and software module, it allows you working in a coherent and continuous environment.

Product

Noise Source

MNS-1

-

Matrix Test Equipment Incorporated

MNS-1 - Matrix Test Equipment Incorporated

The MNS-1 is a shaped noise source that can be used toemulate 2 bands of digital carriers. While it does not havethe necessary attributes to generate a constellation, it doesmimic the loading of QAM carriers. The MNS-2 featuresremotely controllable 6 MHz wide notch filters to allowintroducing a QAM carrier capable of generating a constellationand enabling measurement of Modulation Error Ratio (MER) andBit Error Rate (BER).

Product

Noise & Vibration Analysis

DATS Software

-

Prosig Ltd

DATS Software - Prosig Ltd

DATS is a comprehensive package of data acquisition, signal processing and reporting tools. It is used mainly for noise and vibration analysis, but can be used for a wide range of engineering and general signal processing tasks.