Loop backs
connect input to ouput to test I/O loop.
-
Product
Loopbacks
-
Loopbacck plugs are used for network diagnostics, system configuration testing, and device burn-in. Looping back the signal allows for testing of the optical network.
-
Product
Mezzanine System
5041
System
ECM P/N 5041 provides eight channels of RS485 / RS422 I/O with fixed 120 ohm termination for each channel. Speeds are up to 30M bits per second. All channels power up as inputs. Also transceiver inputs are always enabled for loop back diagnostic use when the outputs are enabled. Software can enable outputs on a channel by channel basis.
-
Product
One Core Loop Tester
-
DAMUL is an innovative and portable optical power checker accompanying 1-core loop back function. DAMUL can check SFP TX and RX power level by simply inserting SFP into it. If you use UPM (Universal SFP-typed Power checker Module) optionally provided, DAMUL can measure optical power. Also, when using SPM (SFP-typed Power checker Module) optionally provided, DAMUL can identify 18 CWDM wavelengths as well as its power automatically. DAMUL provide users high productivity for optical power checking work on fiber optic systems such as WDM-PON.
-
Product
Transponder Panel with GNS/GTN Interface
TA-330XP
-
This transponder panel is layed out to accommodate thecurrent Mode S panel mount units. The transponder caninterface with a GNS or GTN series radio for a morecomplete test of the transponder functions. The panelalso includes altitude, suppression, loop back and thestandard ARINC 429/RS232 interfaces as well. The panelcomes with both a digital voltmeter and ammeter.
-
Product
AC Power Sources, Frequency Converter
MAC-01, -02, -03
-
For reliability, all models of the Titan AC Power Sources/Frequency Converters are fully current limit protected against either continuous or transient short circuit or overload conditions. When an overcurrent condition exists, the internal current control loop overrides the voltage control loop and scales back the sinewave drive until it sees a safe output current level.
-
Product
Wire Harness Tester
Panther4HT Master- Slave DSU
-
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
Product
Antenna, Loop
EM-6871 | 30 Hz – 1 MHz
-
The EM-6871 Antenna can be used with any 50 ohm /Receiver/Field Strength Meter to obtain magnetic field measurements from 30 Hz to 1 MHz.
-
Product
Single Loop Controller
1400+
-
The 1400+ controller is an evolved product from the West N4100. The product benefits from having more versatile features and user-friendly functionalities such as remote setpoint inputs, digital inputs, plug-in output modules, a customisable operator/HMI menu, jumperless and auto-hardware configuration, and 24VDC transmitter power supply.
-
Product
Single Loop Controller
1160+
-
The 1160+ controller is an evolved product from the West N6100. The product benefits from having more versatile features and user-friendly functionalities such as remote setpoint inputs, digital inputs, plug-in output modules, a customisable operator/HMI menu, jumperless and auto-hardware configuration, and 24VDC transmitter power supply.
-
Product
Loop Calibrator
Model KM CAL-904-MK1
-
Kusam Electrical Industries Limited
• 4-20mA (1kΩ Load, 24V Loop Output).• 0-20mA and 0-24mA output ranges.• 0.025% Basic Accuracy.• Auto Ramp and Step functions.• 0-100% output with percentage step option.• 0-24V DC voltage source.• Open loop and overload buzzer alarm.• Low battery indication.• Simple Operation Interface• Warning beeper when output is open• Pollution Degree 2.• Ambient temperature 0~40℃.• Power Consumption 150mA at 24V 1kΩ load
-
Product
Single Loop Controller
1460
-
he 1460 has been designed to provide immediate visibility to the operator. At a glance, the programmable displays will show you the measured variable, the set point and the parameter being edited, the number of cycles or time remaining, the recipe name and number and also whether the cycle is in a ramp or soak mode
-
Product
Loop Powered Indicators
-
DEVAR loop powered indicators are designed to easily convert any standard 4 to 20mA loop signal to readout directly in engineering units. Optional back-lit display available.
-
Product
Single Loop Controller
1462
-
The N4400 is a sophisticated, single loop controller which provides extensive profiling programming options for complex processes. The controller can create a profile with up to 121 segments, store up to 8 programs and configure and store extra programs on a PC.
-
Product
Loop Tack Tester
-
Loop Tack Tester is applicable to measure the tack property of adhesive tapes, pressure-sensitive adhesives (PSA), and adhesive materials according to ASTM D6195.
-
Product
Loop Calibrator
6500 LC
-
Standard Electric Works Co., Ltd
● 4-20mA (1kΩ load, 24V Loop Supply).● 0.025% Basic Accuracy.● Simple Operation Interface.● Auto Ramp and Step Functions.● 0-20mA, 0-24mA selectable.● Incremental percentage setting : 0-100%.● Warning beeper when output is open.● 0-24V output.● The minimum load of 20kΩ on voltage mode.
-
Product
Back Pressure Tester
TU29P
-
Enables Technician to test exhaust back pressure thru oxygen sensor. Oxygen Sensor adapter includes M12 & M18 thread.Special Gauge has two multi-colored bands - idle and 2500RPM, with pressures shown in PSA and bar.
-
Product
Back and Forth Scratching Tester
WGQ-60
-
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800～5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100～5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
Product
24" Front to Back Stiffeners
FB-24
-
Additional aluminum extruded front-to-back stiffeners are available for Vertical Cabinets. Includes installation hardware
-
Product
MULTI-STANDARD LOCAL LOOP SIMULATOR
458-LM-A8-30
-
Accurately simulates attenuation and impedanceFull bidirectional operation at all specified frequencies26 AWG PIC as specified in ANSI T1.417
-
Product
Active Dual Loop Antenna
KH30936
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH30936 active dual loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna power is supplied by the host, which is convenient for outdoor measurement.4. Compared with the single loop antenna, the advantage is to read the maximum value directly, which eliminates the tedious steps of rotating the antenna to find the maximum value and the interference of the human body to the signal.
-
Product
Push Back Probe VF416B180G10
1005149
-
The Push Back Probe VF416B180G10 (item number 1005149) is designed to verify that terminals are correctly locked in connector housings. VF416B180G10 can verify that a terminal remains securely locked in the connector housing and is not pushed back beyond the permitted position during contacting. For VF416B180G10, spring force is 1000 cN at a nominal travel of 5 mm. Pointing accuracy for VF416B180G10 is specified as ±0.1 mm. The electrical rating of VF416B180G10 combines 10 A continuous current with 30 mΩ typical contact resistance. For installation, VF416B180G10 uses an M2.5 x 0.35 thread.
-
Product
Back Pressure Test Kit
389
-
Thexton Manufacturing Company, Inc.
Aids in diagnosing clogged or restricted exhaust systems.
-
Product
Loop and Line Powered Level Switch
Safety IntelliPoint
-
The Safety IntelliPoint level switch provides a capacitance probe level switch with either a current output or relay contacts and “On-Board” self-diagnostics to ensure reliability. This SIL Intellipoint conforms to SIL 2 specifications providing the ultimate in level switch integrity and level sensing elements for a wide variety of temperatures, pressures, and materials.
-
Product
Push Back Probes HVF100
1001837
-
The HVF100 Push Back Probes, designated with order code 1001837, are specifically designed to provide reliable and efficient connection capabilities in various electronic applications. With a total length of 50 mm, the probes feature a precise press ring diameter of 2.20 mm, ensuring compatibility with a wide range of receptacles and test equipment. The design's emphasis on compactness and durability makes it an essential tool for professionals seeking to optimize their connectivity solutions.
-
Product
Push Back Probes (VF3) VF383B0003G15
1005897
-
The Push Back Probes (VF3) VF383B0003G15 are expertly designed contact probes optimized for precision and reliability in various applications. With a pitch of 3.00 mm, they ensure smooth and effective connectivity within electronic circuits, capable of operating in extreme temperatures ranging from -45°C to +100°C. This model supports continuous current up to 8.00 A, maintaining a low typical contact resistance of just 30.00 mOhm, which is crucial for ensuring optimal performance and longevity.
-
Product
Push Back Probes (VF3) VF383B0002G15
1005896
-
The Push Back Probes (VF3) VF383B0002G15 is a high-precision contact probe designed for reliable performance in a variety of demanding environments. With a temperature range of -45°C to +100°C, this probe ensures that it can operate effectively under extreme conditions. Its robust construction features a beryllium copper plunger with gold plating, providing excellent conductivity and corrosion resistance. The brass barrel, also gold-plated, complements the design, ensuring durability and reliability during use.In terms of functionality, the VF3 probe boasts impressive specifications. The continuous current rating is 8.00 A with a typical contact resistance of just 30.00 mOhm, minimizing energy losses and enhancing efficiency. The mechanical specs of the probe include a preload of 300 cN and a spring force of 1500 cN, enabling the probe to maintain consistent contact under various pressures. With an impressive pointing accuracy of ±0.10 mm and a nominal travel of 5.00 mm, this probe is engineered for precision in measurement applications.
-
Product
Push Back Probes (VF3) VF306B200G15S1
1004720
-
The VF306B200G15S1 Push Back Probe from the VF3 series is designed for precision and reliability in critical applications. With a pitch of 3.00 mm, it operates efficiently within a temperature range of -45°C to +100°C, making it ideal for demanding environments. This probe features a basic contact design, ensuring robust and consistent performance. Its significant preload of 1090 cN and a spring force of 1500 cN provide the necessary mechanical advantages for intricate tasks.
-
Product
Push Back Probes (VF4) HVF4
1001841
-
The Push Back Probes (VF4) HVF4, identified by Order code 1001841, are innovative components designed to enhance the functionality of electrical systems. With precise measurements of a total length of 34.00 mm, these probes are engineered with optimal performance in mind. The press ring diameter of 3.70 mm and outer diameter of 3.50 mm ensure a snug fit within various receptacles, while the collar height of 5.70 mm facilitates secure connections. This robust design caters to a variety of industrial applications, promising reliability and longevity in demanding environments.
-
Product
Loop powered Moisture Analyzer
PLMa
-
Multifunctional Multi-Purpose Cost Effective, easy-to-use dew point sensor, dew point probe
-
Product
Push Back Probes (VF3) VF383B0007G15
1006292
-
The Push Back Probes (VF3) model VF383B0007G15 is meticulously engineered to deliver exceptional precision and reliability in various applications. With a pitch of just 3.00 mm, these basic contact probes are optimized for tight spaces, ensuring accurate measurements and connections. Designed to withstand extreme temperatures ranging from -45°C to +100°C, they are suitable for a wide range of environments, making them a versatile choice for both industrial and laboratory settings.
