-
product
PXI-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module
778858-01
96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module—The PXI‑6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Xilinx Zynq UltraScale+ SoM
TE0808-ZU9
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TE0808 is an industrial-grade SoC module integrating a Xilinx Zynq UltraScale+, max. 4 GByte DDR4 SDRAM with 32-Bit width, max. 512 MByte Flash memory for configuration and operation, up to 256 MByte HyperFlash, 20 Gigabit transceivers, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/O’s is provided via rugged high-speed stacking connections.
-
product
Programmable 70W Electronic Load
MightyWatt R3
The All-New MightyWatt revision 3 turns your Arduino Uno R3 or Arduino Zero (M0/M0 Pro) into an electronic load capable of dissipating 70 Watts in a very small form factor. Ideal for testing power supplies, batteries, solar cells, fuel cells or power amplifiers. MightyWatt R3 has a research-grade electronics and is aimed not only at hobbyists but also at professionals.
-
product
XCITE 1100 Laboratory Series
The Xcite 1100 Laboratory Series is the most popular of the Xcite product line because of its large force capacity and broad frequency range compared to its extremely compact size. The 5 GPM 3-Phase hydraulic power supply used in the system provides a high level of low frequency displacement response for testing system subassemblies and non-linear structures such as suspensions and elastomeric dampers. The small piston area of the exciter and the high performance servovalve combine to provide excitation to over 1000 Hz allowing structure borne noise path evaluations.
-
product
SELV laboratory power supplies
PeakTech Prüf- und Messtechnik GmbH
A linearly regulated, stabilized laboratory power supply with a safety transformer. It is ideally suited for teaching aids, schools and universities and offers safe use but also a very good price / performance ratio.
-
product
Memory Test System
T5835
The new T5835 has full testing functionality, from package testing to high-speed wafer testing, for any memory ICs with operating speeds up to 5.4 Gbps, including all next-generation memories from NAND flash devices to DDR-DRAM and LPDDR-DRAM. It can handle 768 devices simultaneously for final package-level testing. It additionally features functions such as an enhanced programmable power supply (PPS) for advanced mobile memories, and a real-time DQS vs. DQ function to improve yield.
-
product
24 V DC Power Supplies
*Space-saving design*High power reserves*Low heating of the control cabinet*Low inrush current*Safe switch-off by circuit breakers in case of short circuit
-
product
DC Power Supply
WPS Series
The WPS Series programmable DC power supply is a high-precision, wide range of voltage & current within the power rating of the power supply, full-featured high power density programmable DC Power Supplies. It can provide wide-range, low-ripple and stable DC output which is used for DC input products and components function testing and experimental simulation.
-
product
Power Supply
P9610A
The P9610A provides the extended operation areas (see below). This means that you have access to 100% power all the time at any voltage or current within the maximum limits. This also means that the P9610A can meet more of your needs, minimizing the number and cost of power supplies you need to purchase.
-
product
1U Rack Adapter for Series HSF-1U, HSF-1UR
RA 19
The 1U high rack adapter will mount four of the low profile 50W, 100W and 150W (Series HSF-1UR or HSF-1U) power supplies. Each plug-in power supply is equipped with a power on/off, indicator LEDs and voltage test points. The RA 19-1U provides access to the DIP switches and rack keying without disassembling the rack. It also provides a redundant scheme with modules 1 and 3 being powered from one a-c input and modules 2 and 4 from a second a-c input. Module numbering is left to right facing the front panel.
-
product
4-Channel ADC Module
FMC164
Sundance Multiprocessor Technology Ltd.
The FMC164 is a digitizer FMC featuring four ADC channels with 16-bit resolution and a 250 Mega samples per second sampling rate per channel. With a flexible clock generation and distribution scheme, the FMC164 allows control on sampling frequency and analog input gain through serial communication with a carrier card. The FMC164 design is based on the TI ADS42LB69 Dual Channel 16-Bit 250 MSPS A/D, is equipped with power supply and temperature monitoring, and offers several power-down modes to switch off unused functions.
-
product
725-Watt (28VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX55HS
NAI’s VPX55HS-31 is NAI's latest +28 VDC Input, VPX DC/DC Converter. The VPX55HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
product
3U VPX Power Interface Board VITA 62
106PIBC301-0000R
3U Convection Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
product
Beam Directional Power Supply Battery 40 to 160 kV
CP160B
Next to the CP120B, the CP160B is the slightly more powerful version of our ultra-light, compact and battery operated constant potential portable X-Ray generators. Allowing penetration reaching up to 30 mm for steel, the CP160B is the perfect tool for specific NDT applications that require repetitive short exposures, as well as security applications.
-
product
POL Converter
Renesas offers a rich product lineup focused on the step-down type switching power supplies with built-in FET from small current applications to large current applications, depending on the supplied current.
-
product
SA1500X, 1.5 GHz, ±8 V, 10X Attenuation, Single-Ended Active Oscilloscope Probe
784256-01
The SA1500X is single-ended, active voltage probe that is used for many different high-speed measurement applications. The probe is powered by an included auxiliary power supply that is internationally compatible and certified. You can use it with oscilloscopes that provide 50 Ω input impedance.
-
product
RF Amplifier
SA1012
Hangzhou Softel Optic Co., Ltd.
*Forward path use import low noise push pull amplify module or GaAs push pull module,2 Power-Double module or GaAs amplify module are used as output stage, Output level is stable and nonlinear index is good, import high index amplify module are used on return path, It's distortion is little and SNR is high.*It is more convenient to debug because of plug-in(or adjustable) duplex filters, plug -in fixed(or adjustable)equalizers, plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
-
product
Accessories
Blonder Tongue Laboratories, Inc.
From a headend rack to a power supply, make sure you have everything you need by uncovering the wide range of hidden gems and must-haves from Blonder Tongue.
-
product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-14
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
48V / 300 Amp Load
BD18-48P
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
product
- Optical / RF Converter
OPT 80
Calibrated measurement of the optical power of satellite and terrestrial TV signals distributed in optical fiber Calculation of optical signal losses on distribution Measurement of digital parameters (BER - MER - NM etc.) of optical signals converted into RF Visualization of optical carriers in RF Field Metric Spectrum Analyzer Power Meter Optical Field Meter Display Optical RF Power Supply Line Link Meter (LNB power supply ) Optical LNB power supply 13V 500mA with short circuit and overload managementAcquisition of optical measurements using the field meter Data Logger Option: certification of the OPT80 calibration and optical power measurements
-
product
ATE Computer
MS 1201
This system used for multi-purpose applications such as data acquisition and Automatic Test Equipment. ATE Computer has ISA Bus based eleven slots with inbuilt power supply. Micro Processor board or USB Controller is used to drive the back plane.
-
product
6U CompactPCI Enclosures & Systems
1~9U CompactPCI chassis for 6U CompactPCI boards , most of which are with front/rear panel I/O, H.110 CT bus and redundant power supplies.
-
product
DC Power Supply
PW-7033
*Portable type, small size design*Overload protection*3 sets output: 0~32V/0~3A x 2 + 5V/3A*Parallel: 0~64V/0~3A or + 32V ~ -32V/0~3A*Series: 0~32V/0~6A*3 digits, 4 sets LED display, Green is display for voltage, Red is display for current, easy to read, no mistakes.
-
product
High-accuracy Multi-channel Programmable DC Power Supply
N39400 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N39400 series is a high-accuracy & multi-channel programmable DC power supply with standard 19-inch 2U design, available for cabinet installation. Single N39400 supports Max. 4 channels output, with channels isolated. Both local operation on front panel and remote control on a computer are supported. N39400 can be widely used in lab test, system integration test, production aging line, etc.
-
product
Clock Generator
CG-2000
Supports power supply and video / audio clock redundancy. The top model in the CG series equipped with various functions required for broadcasting stations and post-professional sites.
-
product
32-CH Discrete Input Modules
HSL-DI32-M-N/HSL-DI32-M-P
- Slave ID consumption: 2 consecutive from odd- "N" type for NPN sinking type sensor or dry contact; "P" type for PNP sourcing type sensor or wet contact- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ± 10 mA (Max), ± 12.5 mA (Peak)- Input voltage: ± 40 V (Max)- LED indicator: Power, Link and Input status- Power supply: +10 V to +30 VDC
-
product
Laboratory Switching Power Supplies
PeakTech Prüf- und Messtechnik GmbH
The double function buttons (coarse and fine adjustment) allow an easy, precise and quick adjustment of the voltage and current values due to the rotary encoder and the microprocessor control.
-
product
Power Interface Board 3U, 1PSU connector
106PIBM301-0000R
The PIB 3U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
Passive Pulse Splitter
SY037
The SY037 passive pulse splitter is ideal for converting pulses from meters or other turbine devices and transmitting the same pulse to three outputs to enable three separate instruments to measure the rate simultaneously. It needs no power supply. It functions simply from the pulses of the meter driving it. It is convenient for meters and any pulse generating device with reed switches, open collector or current source.
