Carl E. Holmes Company
CEHCO provides SCR and Diode Rectifiers for a variety of applications that includes anodizing, water treatment, general metal finishing, crane duty, electrochemical applications, and the latest development in power conversion technology.
- (714) 666-0787
(714) 624-4740 - quote@cehco.com
- 1139 N. Kraemer Place
Anaheim, CA 92806
United States of America
-
Product
Bridge Rectifier Assemblies
-
Bridge Rectifier Assemblies are constructed by packaging diodes and/or SCR components with heat sink extrusions in a bridge circuit.CEHCO uses M, T, N and W heat sink extrusions to build rectifier assemblies.
-
Product
SCR Controller with Regulator
-
The SCR Controller and the Regulator Board are used in SCR controlled power supplies.CEHCO offers single phase and three phase SCR Controllers with Regulator Boards.
-
Product
VARIABLE TRANSFORMER DC POWER
208163V
-
Motorized Variable Transformer Controlled Power Supply, P/N 208163VInput power: 208 VAC, 6 Amps, 3 PH, 60 HzOutput: 0 to 120 VDC, 16 Amps max.Ripple: 5%Manual control with variable transformerCircuit breaker / ON OFF on the 208 VAC, 3 PH input lineProtection fuse provided on the outputPOWER ON lightIndoor enclosure: 24H x 20W x 9DVoltmeter and ammeter are installed to monitor the output.All input/output connections are available inside the enclosureSystem includes main unit and remote assembly.
-
Product
SCR Controlled DC power Supplies
-
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single-phase or three phases. With single-phase AC input, the DC output ripple is very high (50%). With three-phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three-phase AC input instead of a single phase.
-
Product
Active Switching Rectifiers, 2 KW, P/N 6016C
-
- Active Switching Rectifier, 2 KW, P/N 6016C- Input Range: 9 VAC to 35 VAC, 3 PH- Frequency Range: DC to 10 kHz- DC output: 13.5 VDC, 70 Amps without any heatsink (Test #1)- DC output: 13.5 VDC, 150 Amps with heatsink (Test #2)- Dimensions: 8″W x 8″L x 3″H or similar- AC to DC and DC to DC applications- Generates less heat as power MOSFET Switching is used- The output voltage is the same as the input voltage
-
Product
Replacement Selenium Surge Suppressor Specialists
-
Surge suppressors are used to protecting circuits from transients (sudden, brief increases in voltage). Transients of widely varying magnitudes are caused by such circuit components as motors, coils, magnets, relays, and transformers. They are found in all electrical systems and are notorious for damaging diodes, SCRs, transformers, triacs, and relay contacts.
-
Product
Repair of Solid State Switch, P/N 60-SS480
-
Solid State Switch P/N 60-SS480Input: 480 VAC, 3PH, 60 HzOutput:480 VAC, 3 PH, 60 HzControl Voltage: 120 VAC, 1 PH, 60 Hz
-
Product
Transformer Rectifier Assemblies
-
Transformer rectifier assemblies are very useful in OEM applications when unregulated DC output is required. Input power can be single-phase or three phases. With single-phase input power, the output ripple is 50%. With three-phase input power, the output ripple is 5%. A 5% output ripple is a clear advantage. Hence, transformer rectifier assemblies with three-phase input power are more popular. Circuit breakers, fuses, voltmeters, and ammeters can be added per customer requirements. The assemblies can be an open frame or inside an indoor enclosure.
-
Product
Surge Suppressor to Suppress SCR Spikes from Customer Equipment Going Back to Utility Power, P/N 5965C
-
This Suppressor Board is ideal for SCR Controlled Power Supplies when SCR control is on the primary side.The Suppressor Board will prevent SCR spikes to go back into the 480 VAC utility power lines.
-
Product
SCR Diode Testers
-
SCRs and Diodes are used in the power sections of various power systems. A SCR Diode Tester is an important piece of equipment to determine if a SCR or a diode is defective in a power circuit. It is difficult and time-consuming to troubleshoot SCRs and Diodes with a digital meter.
-
Product
MOTORIZED VARIABLE TRANSFORMER CONTROLLED POWER SUPPLY
-
Motorized Variable Transformer Controlled Power Supply, P/N 18534PSInput: 460 VAC, 3 PH, 60 HzOutput: 0 to 250 VDC, 200 Amp max.Variable Transformer is used to vary the output. SCR controller is not used, as it generates harmonics.Input control is 0 to 3.6 VDC.Indoor enclosure.Output voltage and current feedback as 4/20 mA for PLC interface.All input/output connections are inside the enclosure
-
Product
High Voltage Diode Assemblies
-
High voltage diode assemblies are built by adding diodes in series to yield a higher peak inverse voltage. For example, if each diode is rated for 1200 peak inverse voltage (PIV), then six diodes in series would have a total peak inverse voltage of 7200 PIV. The detailed circuit is shown below.
-
Product
Repair of Six Diode Bridge Assemblies, P/N 5989C
-
CEHCO is specialist in repair of various rectifier assemblies. One such assembly is shown below:Specifications:- Six Diode Bridge Assembly, P/N 5989C- AC input terminals: (3, 4 , 5)- DC output terminals: (1), POSITIVE and (2), NEGATIVE
-
Product
IGBT Power Supply, 0 to 16 VDC, 3000 AMPS, P/N 6134C
-
IGBT Power Supply, 48 KW, P/N 6134CInput: 480 VAC, 3 PH, 60 HzOutput: 0 to 16 VDC, 3000 AmpsRipple does not degrade when the output voltage is reducedDigital remote with Voltmeter and Ammeter and potentiometers includedDimensions: 20.00”W x 32”H x 24.5”D.Estimated weight: 300 lbs.
-
Product
5000 AMP DC Rectifier - Air Cooled, P/N 6037C1
-
Air Cooled SCR Controlled Power Supply, 50 KW, P/N 6037C1Input: 480 VAC, 60 Amps, 3 PH, 60 HzOutput: 6 to 10 VDC, 5000 Amps maxContactor and overload relay are installed for protectionStart / Stop capabilityEPO capabilityManual voltage control and current limitOutput voltage and current are displayed on the voltmeter and ammeterIndoor enclosure, 68″H x 65″W x 36″DAll input/output connections are inside the enclosuresEstimated weight: 1000 lbs.
