-
Product
Rack Mount Hawk/PC Chassis
9381
-
A slide-in replacement for a Nova/Eclipse. A 10.5 inch (267 mm) high chassis with a 5-position Nova/Eclipse backplane and card cage, 450 watt power supply, cooling and rack slides. Accommodates up to five DG-compatible 15" x 15" (381 x 381mm) boards, a PC motherboard, diskette drive and up to three visible half-height disk drive bays and one internal half-height drive bay.
-
Product
120W Power Supply, 15V, 7A or 30V, 4A
E3632A
-
Keysight basic DC power supplies offer essential features for a tight budget. The single output, 120-200 W, GPIB, E3632A-E3634A provide dual range outputs; small, compact size for bench use; low output ripple and noise; as well as built-in measurements and basic programmable features with GPIB and RS232 interface. The Keysight 120W, GPIB, single output E3632A is a high performance supply optimized for manual and basic automated testing; and, with a combination of benchtop capabilities and system features, it is designed to help improve measurement quality and reduce test time.
-
Product
Accessory Power
-
An accessory power system gives options to help simplify power supply connections and can help make a product more marketable. It can also open up opportunities for new markets.
-
Product
Multi-Wafer Test & Burn-in System
FOX-XP
-
The key features of the new FOX-XP test cell that contribute to the cost-effectiveness of the solution include the ability to provide up to 2,048 "Universal Channels" per wafer, which allows the system to test all the devices on the wafer in parallel. The new "Universal Channel" architecture allows any channel to be any function (I/O, Device Power Supply (DPS) or Per-pin Precision Measurement Unit (PPMU)). This enhanced architecture now allows customers to perform per pin parametric testing, more extensive digital pattern test with deeper data stimulus / capture memory (32M per pin), and deeper scan (768M) optimized for BIST/DFT testing.
-
Product
UPS (Uninterruptible Power Supply)
-
The UPS (Uninterruptable Power Supply) by Allied Edison is a light weight (7.2 lbs), portable, non-variable source that converts a 12 Vdc Lithium Ion battery to output 110 vac sine wave at 60 hertz. It also has four 12Vdc output jacks, and 4 USB ports to power electronic equipment such as computers or used to supply cell phone chargers, etc. It has a strong built in flashlight. The UPS plugs into a standard 120 Vac, 60 hertz receptacle for charging and indicates percent battery capacity remaining on a digital meter located on the front panel. The UPS can also be charged by a solar cell, sold separately or can be plugged into a vehicles cigarette lighter receptacle for use in remote areas. The UPS is an excellent compliment to the VS-3 power supply where a technician needs a variable AC/DC source and cannot run a power cord due to the remoteness of the work area.
-
Product
Industrial AC Power Supply 2U Form Factor, 350W
APS-9235XU
-
- Power (typical): 350W- AC Voltage Input Range: Universal- Certifications: UL/cUL/TUV/CCC- Dimensions: 215 x 100 x 70 (mm)
-
Product
Power Supplies
MP-550B
-
With dual PCI-E connectors, the MP Series carries all its essentials to power your system. Enjoy the graphic rendered programs and games without the threat of overheating. Its dark aluminum chassis not only looks good, but dramatically relieves heat built-up. The 120mm fan enhances the already efficient heat dissipation rate and helps balance the cooling system with noise level. The MP Series is great for high end users to everyday casual users. Whatever your system needs, the MP Series can deliver.
-
Product
Aerospace and Aviation Solutions
-
SCOEs and EGSEs by LXinstruments are used during test and validation of satellite assemblies and modules in aerospace applications. As an example, we implemented solar array simulators, battery simulators and high-power load racks for a German satellite manufacturer for testing satellite power supply systems. Due to the high power ratings, the systems are partially equipped with water cooling. Specialized switching modules were developed for switching DC currents at high voltage levels; these can be programmed with SCPI commands via Ethernet.Our modular OTP² functional test platform is ideally suited for implementing durable, reliable test systems, e. g. for in-flight entertainment applications. Since the OTP2 platform is based on open interfaces, it can be quickly and easily adapted to any required communication busses and ARINC interfaces.
-
Product
Power Supply, 40V, 125A, 5000W
N8756A
-
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight N8756A is a 40V, 125A, 5000W, single output power supply in a small 2U package.
-
Product
- Optical / RF Converter
OPT 80
-
Calibrated measurement of the optical power of satellite and terrestrial TV signals distributed in optical fiber Calculation of optical signal losses on distribution Measurement of digital parameters (BER - MER - NM etc.) of optical signals converted into RF Visualization of optical carriers in RF Field Metric Spectrum Analyzer Power Meter Optical Field Meter Display Optical RF Power Supply Line Link Meter (LNB power supply ) Optical LNB power supply 13V 500mA with short circuit and overload managementAcquisition of optical measurements using the field meter Data Logger Option: certification of the OPT80 calibration and optical power measurements
-
Product
24" Solid Fixed Storage Shelf, 30"D
SS-2430
-
Sturdy 24" shelf formed of one piece of 16 ga. CRS bolts to panel mounting rails. Supports heavy chassis or power supplies or provides storage for tools, test leads, chart paper, etc.
-
Product
Advanced Power System - Dynamic DC Power Supply, 20 V, 50 A, 1000 W
N7951A
-
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
Product
IC & Transformer
-
Mornsun Guangzhou Science & Technology
MORNSUN launched the self-designed electronic integrated circuits according to the different product lines, types of the integrated circuit include AC/DC power supply control ICs, DC/DC power supply control ICs, interface ICs, start-up ICs, contactor power saving controller ICs and digital isolator ICs. MORNSUN IC chip can be widely used in industrial equipment, process control, data acquisition system, building automation, smart meter, etc. Adopting MORNSUN's AC/DC transformers and DC/DC transformers, with the use of its control ICs, can achieve wide voltage input flyback power supply design with multiple protection functions and superior EMI performance. We hope that those power transformers along with the integrated circuits & chips electronics can be an ideal fit for your application needs.
-
Product
Self-Rectified Generator Power Supply Mains 50 to 180 kV
SITEX C1802S
-
Self-Rectified Generator Power Supply Mains
-
Product
Power Quality Analyzers
APQM-702/APQM-703
-
It can be powered from the L phase.It is intended for use in virtually all types of networks from 64 V to 760 V directly, with special consideration for measurements on low-voltage poles, due to its ease of connection.It has an independent power supply and is therefore particularly suitable for measurements outside of voltage transformers. It can also be adapted for measurements on DC voltage systems.Real-time remote configuration and data transfer (GPRS) using a built-in GSM modem
-
Product
DC Bench Power
XPF Series
-
AMETEK Programmable Power, Inc.
The Sorensen XPF is a new type of bench power supply designed to meet the need for flexibility in the choice of voltage and current. Typically, the maximum voltage and maximum current are not required simultaneously. The PowerFlexTM design enables higher currents to be generated at lower voltages within an overall power limit envelope. This is achieved by using the latest switch-mode technology.
-
Product
Loop-Powered Transmitters and Drivers
4-20mA
-
Loop-Powered Transmitters convert the output from proximity probes, seismic sensors, into a 4-20mA DC current, which is proportional to the input being measured. The transmitter converts the displacement or vibration signal to DC voltage and/or current for a DCS or PLC system. They control a 4-20mA current loop for a specified vibration range (ex. 0-5 mils peak-to-peak). The transmitters have a two-wire hook-up, powered solely by the loop current and have a power supply range of 15 to 36 volts.
-
Product
CompactPCI 2 Slot 1U
-
1U, 19″ Rackmount system with hot removable CPCI 3U Power Supply, four Powerful Fans and CompactPCI Backplane. The system support 6U cards Front and Rear. Additional four fans are available for optimal Front and RTM cooling solution. The Backplane is compliant with PICMG 2.0 R3.0 with 64bit 66MHz & supports boards with hot swap capability PICMG 2.1 R2.0. All five CompactPCI connectors (J1-J5) are available on the backplane. The system slot is located on the lower-slot.
-
Product
H.V. Probes
PD-28
-
Standard Electric Works Co., Ltd
● Measures both AC and DC voltages with digital multitester.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.
-
Product
PXI-6713, 12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
777795-01
-
12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6713 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6713 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
1-, 10-, 40-Gigabit Ethernet Portable Recorder
Talon RTR 2735A
-
- Designed to operate under conditions of shock and vibration- Portable system measuring 16.0" W x 6.9" D x 13.0" H- Lightweight, approximately 25 pounds- Shock- and vibration-resistant SSDs perform well in vehicles, ships and aircraft- Records gigabit, 10-gigabit or 40-gigabit Ethernet streams- TCP and UDP protocols- Copper or optical interfaces- Aggregate recording rates to 4.0 GB/sec- Windows® Server 2016 workstation with a high performance Intel® Core™ i7 processor- Up to 61 terabytes of SSD storage to NTFS RAID solid state disk array- Multiple RAID levels, including 0, 1, 5, and 6- SystemFlow® GUI with Signal Viewer analysis tool- C-callable API for integration of recorder into applications- Optional file headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 10-36 VDC power supply
-
Product
DC System Power Supply, 8 V, 90 A, 720 W
N5742A
-
The single output, 720 W N5742A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current
-
Product
4kW Electronic Load
PT04-48
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 48V and 24V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
Product
Pocket Size Digital Multimeter
HH2106
-
Basic Accuracy 1.2%. Jumbo LCD display 2000 count, 11mm figure height. Manual Ranging at your choice (6 Range). Manual Ranging at your choice. High Voltage test up to AC 500V and DC 200V. Resistance test up to 2000KΩ. Diode test. Independent 12V "A23" power supply
-
Product
Quiet Safety 4U Rack Mounted Industrial Chassis With 14-Slot Backplane And Motherboard
RK-620 Series
-
- EIA RS-310C 19” rack mount standard- Supports 14-slot backplane and ATX motherboard- Two 5.25” external, one 3.5” external and one 3.5” internal drive bay- Two USB ports inside front I/O- Replaceable, easy-to-clean air filter- PS2 ATX power supply- Low noise 12cm PWM controlled (103 CFM)
-
Product
End of Line Test System for Automotive Seats
AS519
-
AS519 is specifically designed to perform ECU’s EOL tests in the automotive industry. It integrates a programmable power supply up to 20V 20A with high reading resolution. Interaction with the DUT is established through CAN bus by an interphase adapter in a USB port of the test managing computer.
-
Product
Power Supplies
VP SERIES
-
Crafted for quality, performance and incredible value. This entry-level solution gives you everything you need in a power supply. No twinkly lights or glittery paint jobs - a 120 mm fan for effective and quiet cooling, dual +12V rails for amazingly stable power and heavy-duty protection circuitry for peace of mind, no matter how demanding your system. And it comes with all the assurance of Antec's AQ2 Antec Quality 2 year limited warranty. All the features, none of the waste: for builders that are strictly business, the VP550F is strictly power.
-
Product
Bench Power Supply, Single, Adjustable, Fixed, 1 Output, 13.3 V, 14.5 V, 15 A
72-8110
-
The 72-8110 is a compact switch mode Power Supply features a very compact footprint that makes it an ideal match for portable communications equipment. Its 50% duty cycle surge rating is comes in handy in demanding transmitting situations. It is also perfect for two-way radio (including HF) and audio equipment including auto sound and multimedia systems. This fixed voltage switch mode power supply is designed with high RFI stability and is especially suitable for two-way radio and communications equipment. Constant current circuitry is used for overload, short-circuit and over-temperature protection. Output current and voltage drop to a safe level when any fault occurs. This power supply also has over voltage protection to prevent connected equipment from damage.
-
Product
Power over Ethernet (PoE) DC/DC
-
An isolated 25W, PC/104-Plus form factor, 802.3af/at compliant, PoE PD power supply. The Class 4 signature supports up to twice the power of 802.3af compliant PD devices. Designed to power a single board computer from DC power extracted from a CAT5 cable sourced by an 802.3af/at compliant PSE device configured as either an endpoint or midspan device.
-
Product
45~1050MHz FTTH CATV O/E Convertor
H9008A
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Guangtai H9008A series CATV converter for digital television, fiber to the home. This machine adopts the high sensitivity optical receiving tube, without power supply, no power consumption. When the input optical power output level Pin=-1dBm, Vo=6 8dB V, can be economically and flexibly apply the integration of three networks, fiber to the home network application.
