Signal Conditioning
The processing of signals to reduce noise level, amplify, attenuate, or otherwise condition.
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Generators, Signal Meters, Signal Conditioners
-
product
Signal conditioning
Simple parameterization of the sensors and visualization of the measured values via the on-site display.
-
product
RTM Discrete Signal Conditioning Board
MS 3632I
CPCI Rear IO Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3639i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
product
RTM Sensor Signal Conditioning Board
MS 3631I
CPCI Rear IO Sensor Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on LAOA, RAOA, AOSS (2), DCM (3), PCS (3), RSA (5) & ASA (4) and TAT sensor interface. This card shall handle excitation, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
product
Signal Conditioning
Various preamplifiers and signal converters extend the range of applications for Elsys data acquisition systems.
-
product
16-Channel Bridge Signal Conditioning Unit
ProDAQ 6716
16-Channel Bridge Signal Conditioning Unit
-
product
Signal Conditioning System
SCS-801
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.The SCS-800 takes advantage of the increasing capabilities of notebook and desktop PCs by leveraging off the PC's strengths. It provides a high-performance, flexible solution whether used as a conditioning front-end for desktop systems in the factory or as a mobile solution for portable systems in the field.
-
product
Signal Conditioning System
28000
The Precision 28000 Signal Conditioning System makes it easy to manage a test with up to 256 channels of fully programmable transducer conditioning. Choose a mix of bridge, charge, IEPE w/TEDS, voltage (filter amplifier), strain, thermocouple, RTD/potentiometer, frequency, or other transducers. Self-tests traceable to NIST. 4, 8 and 16-slot rugged and transportable mainframes feature integrated cooling. Customize the 28000 for high-speed transient applications, static applications, or a combination of both.
-
product
Sensor Signal Conditioning System
SCS
SCS Sensor Signal-Conditioning System complements the iDSC 1816 anti-aliasing board to provide a continuous path in a single package: starting with raw measurements at the sensor and ending with conditioned anti-aliased data logged to disk on a PC.
-
product
IEPE Signal Conditioning Amplifiers
Although IEPE (Integrated Electronics Piezoelectric) sensors is not a new technology there are a wide variety of applications where the measurement instrumentation is not configured with IEPE signal conditioning built in. In these situations it is necessary for the IEPE supply to be provided by an external source. Usually this type of instrument will also provide th user with the option to add gain to the signal being conditioned. The Kemo range of IEPE signal conditioning instruments can be used as stand alone conditioners/amplifiers are many of them can also be integrated with filters.
-
product
Isolated Process Control Signal Conditioning Products
SCIM7B
SCIM7B Isolated Process Control Signal Conditioning Modules provide a complete selection of backpanels DIN rail mounting accessories, interface cables and rack mounting hardware.Each SCIM7B module provides a single of isolated analog input or output. Various input modules accept analog voltage or current signals from all types of field sensors and sources, filter, isolateamplify, linearize and convert these input signals to high-level analog outputs suitable for use in a process control system. Output modules accept high-level analog voltage signals from a process control system, then buffer, isolate, filter, convert and amplify before providing a current or voltage output to a fielddevice.
-
product
Signal Conditioning
The output of an inductive (magnetic reluctance) speed sensor is an alternating voltage in which both the frequency and magnitude depend on target speed. The TTL Interface Adaptor converts this voltage into a TTL logic signal whose frequency corresponds to tooth passing frequency. The magnitude of the output signal from the interface is independent of the tooth passing speed.
-
product
8 Channel Sample & Hold and Signal Conditioning Board
Same features of 8 Channel Sample & Hold and Signal Conditioning Board plus connection and transient protection for Group3 B (digital) and D (analog output) boards.
-
product
PXI Signal Conditioning
For RF and Microwave measurements, Keysight PXI signal conditioning modules modify an analog signal to meet the requirements of the next stage for signal processing. Signal conditioning examples include amplification, attenuation, converting and filtering.
-
product
USB Signal Conditioning Products
Signal conditioning can include amplification, filtering, converting, range matching, isolation and any other processes required to make sensor output suitable for processing after conditioning. It is primarily utilized for data acquisition, in which sensor signals must be normalized and filtered to levels suitable for analog-to-digital conversion so they can be read by computerized devices.
-
product
Charge Amplifiers & Signal Conditioning
The use of charge amplifiers alongside piezoelectric charge output sensors is still widespread in many industries. This is due to the rugged and high temperature capabilities of the sensors. There are many challenges in using these sensors and it needs a good understanding of the technology to get a quality, noise free signal for accurate data.
-
product
Signal Conditioning Modules
Signal conditioning modules provide signal conditioning on a per-module basis for various types of sensor or signal.
-
product
4 Channels of Strain Gauge Inputs for the SCS-800 Signal Conditioning System
SCS-817
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Signal Conditioning and Filtering
MSXB 065
The MSXB 065 Signal Conditioning Expansion Board provides filtered analog signal conditioning for voltage signals for Data Acquisition Processor systems. Each board has differential inputs; jumper-selectable simultaneous sampling; jumper-selectable gains of 1, 5, and 25; fourth-order anti-alias filters, cutoff frequencies from 100 Hz to 50 kHz.
-
product
Signal Conditioning and Filtering
MSXB 067
The MSXB 067 Signal Conditioning Expansion Board provides analog signal conditioning for strain gauges, load cells, RTDs, and other resistive sensors. MSXB 067 provides a flexible interface for quarter-bridge, half-bridge, and full-bridge sensors, with two to six wires for each sensor, with or without voltage sense feedback. A small daughterboard supports user-supplied bridge completion resistors.
-
product
4-Channel Strain Gage Amplifier Module for the SCS-800 Signal Conditioning System
SCS-824 Series
The SCS-824 series provides 4 channels of strain gageinputs for the SCS-800 signal conditioning system. TheSCS-824 series interfaces all strain gage types, fromsingle-element quarter bridges to 4-element full bridges
-
product
18 GHz Up/Down Converter & Signal Conditioning
SC2250
The SC2250 extends the useful range of traditional 6GHz RF instruments for operation at microwave frequencies up to 18GHz. It provides excellent integration capability with other modular products such as National Instrument’s Vector Signal Transceiver (VST). Selectable filtering is provided for signal conditioning applications requiring spurious and harmonic rejection.
-
product
Signal Conditioning Carrier
ProDAQ 5720
The ProDAQ 5720 Signal Conditioning Unit provides power and cooling for up to two Signal Conditioning Cards from the ProDAQ 58xx Series. These Signal Conditioning Cards provide conditioning for 8 or 16 channels and can be used directly with Bustec’s high-performance ProDAQ ADC function cards such as the ProDAQ 3416 16-ch. Sigma-Delta ADC Function Card or the ProDAQ 3424 8-ch. Sigma-Delta ADC Function Card.To connect the function cards to the signal conditioning cards SCSI-style cables from the ProDAQ 8010-Bx Series are used. They provide shielded twisted pair connections for signals and control.
-
product
8 Channel Sample & Hold and Signal Conditioning Board for Group3
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
product
Portable Signal Conditioning System
SCS-800
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.
-
product
Isolated SCIM5B Analog Signal Conditioning Products
SCIM5B
BEE INSTRUMENTS offers cost- effective, isolated industrial signalconditioning modules. The SCIM5B analog modules are form, fit, and functional equivalents to similar products from other manufacturers. The product range includes a complete selection of backpanels, interface cables, racks, fuses, jumpers, power supplies, and other accessories.
-
product
RTM Analog & Discrete Signal Conditioning Board
CPCI Rear IO Analog and Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3663i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector. And Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector
-
product
RTM Analog Signal Conditioning Board
MS 3633I
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
product
Signal Conditioners
SC-1300
The SC-1300 family of signal conditioners can convert the most commonly used process signals into conditioned current and voltage outputs, needed for control systems and monitoring devices. Dedicated functionality and isolation from control systems improves reliability.
-
product
PXIe-4492, 204.8 kS/s, 113 dB, 2 Gains, 0.5 Hz AC/DC-Coupled, 8-Input PXI Sound and Vibration Module
781490-01
204.8 kS/s, 113 dB, 2 Gains, 0.5 Hz AC/DC-Coupled, 8-Input PXI Sound and Vibration Module - The PXIe‑4492 is designed for sound and vibration applications. With 24-bit analog inputs and IEPE constant current signal conditioning, the module is ideal for making precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. The PXIe‑4492 delivers simultaneous sample on all channels. In addition, it includes built-in antialiasing filters that automatically adjust to your sample rate, software-selectable input gains, and TEDS smart sensor support for error-free setup. Common applications include noise, vibration, and harshness (NVH) analysis; large microphone arrays; and dynamic structural test.
-
product
RM-26999, 4-Channel Power Measurements Conditioner
786328-01
The RM-26999 is a rack-mounted, signal conditioning device that connects to several simultaneous-sampling multifunction I/O devices for power measurements. It features four voltage input channels with peak voltages up to 2,000 V and four … current transducer ports for current measurements. The current transducer ports are optimized for flux-gate transducers by providing all the power, communication, and signal lines required for accurate measurements.
