Circuit
-
Product
Extender
3690-15
-
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards.
-
Product
Insulation Tester
AD-2050
-
Measuring voltage control during measurement, Insulation measurement up to 400 G W. Elimination of trough resistance insulation. 3 connectors measurement method, Autoranging, Auto-Discharge facility safely discharges the connected circuit after a test, 5 minutes, 1 minute at will shorter measurement,
-
Product
Audio MEMS Sensors
-
An audio MEMS sensor is an electro-acoustic transducer housing a sensor (MEMS) and an application-specific integrated circuit (ASIC) in a single package.
-
Product
Current Clamps and Sensors
-
Are designed for measuring leakage current diverted towards the earth. It enables the fault to be located or anticipated without disconnecting the equipment linked. It is specially designed to detect low fault currentson power circuits.
-
Product
Adjustable Test Stab Set
-
The ETI adjustable test stab set may be used with your high-current circuit breaker testers to maximize efficiency and convenience for testing multiple breakers. Our stab system allows your technicians to test breakers in-place and avoid jacking breakers up or down for testing. By combining mobility and flexibility into one simple system, this stab set is a proven improvement over conventional designs. The components in the adjustable stab set are made of 120 pounds of 110 copper.
-
Product
Thermal Cycling Test Equipment
-
Wewon Environmental Chambers Co, Ltd.
IC welding to PCB, IC is integrated in the chip general purpose circuit, it is a whole. Once the inside is damaged, the chip will be damaged. The goal of printed circuit boards (pcbs) is to connect IC and discrete components to form a larger working circuit. Thermal cycling equipment can detect the defects and hidden dangers of welding components in the production process, decreasing failure rate. When it fails, components can be replaced in timehttps://www.wewontech.com/thermal-cycling-test-equipment/
-
Product
Energized Cable Identification System
LCI™
-
The LCI™ system is intended for energized cable identification on secondary and primary circuits. This innovative solution features a dual frequency technique that eliminates false identifications. The LCI™ is designed to be easy to use, safe for the user and cost-effective.
-
Product
Panelized PCB Tester
-
Removable nests are designed to configure base test system to accept panelized circuit boards for rapid functional test.
-
Product
AC Voltage Detector
VT-2
-
The Non-contact AC Voltage Testers are easy to use — just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there’s voltage present. Electricians, maintenance, service, safety, personnel, and homeowners can quickly test for energized circuits in the workplace or at home.
-
Product
Automatic Component Analyzer
TH2829A
-
Changzhou Tonghui Electronic Co., Ltd.
By dint of leading impedance measurement technology and rich R&D experience, Tonghui continuously introduces representative impedance measurement product --- TH2829 series automatic component analyzer is another excellent product we have produced. TH2829A automatic component analyzer possesses a higher test speed, a more comprehensive analysis function and friendly human-computer interactive experience by adopting the latest high-speed processor and a new software system. Well-designed measuring circuit and optimized algorithms further enhance the test stability of low-D capacitance and high-Q inductors. The instrument is provided with 10V AC test level, 10V/100mA bias current and standalone 10V/50mA DC current, making it convenient for applying in the test of all kinds of active/ passive devices. Main/ sub parameters display, enhanced display system design, 150-points list sweep and graphical analysis capabilities of multiple parameters meet the most application requirements of customers.
-
Product
POWER PROBE III WITH CLAM SHELL - GREEN
PP3CSGRN
-
*Power Probe 3 is a digital multimeter that provides diagnostic power with the flip of a switch*Determine if motors, lights, fans, relays and circuits are operational on and off the vehicle by applying battery power or ground through the tool*Easy-to-read dual polarity indicators feature a red (+) symbol to indicate positive voltage and a green (-) symbol to indicate ground
-
Product
100 Amp Intelligent Power Management
IPMDS100
-
- Intelligent Power Management System- 3 - 20 Amp Single Phase Outlets- 3 - 40 Amp Three Phase Outlets- 2 - 60 Amp Three Phase Outlets- Automatic Load Shedding- 100 Amp Mil Spec Input and Output Connector- Easy Access Circuit Breakers- Phase Over Current Protection- Low Voltage Warning- Built In Press to Test
-
Product
1U Power Supply ModelsAC-DC Single Output
-
Conserve space with mini-modules as small as 2.3" x 1.8" x 1.0". Models with outputs ranging from 1 to 75 volts, and from 30 mA to 2.5 amps are available. All feature excellent regulation and ripple parameters, and are short circuit protected.
-
Product
Optical Sensors
-
module is basically comprised of a photomultiplier tube to convert light into electrical signals, a high-voltage power supply circuit, and a voltage divider circuit to distribute the optimum voltage to each dynode, all assembled into a single compact case. In addition to these basic PMT modules, Hamamatsu also provides modules having various additional functions such as signal processing, cooling and interface to PC.
-
Product
High Insulation Digital Clamp Tester
HCL-5000KN+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Wide AC current measurements for 0.01A～500A.・Easy operation, Push to Open and Pull to Disconnect Mechanism.・Safe AC current measurements for high voltage circuit (AC80 to 7000V).・Auto power off function and Splash proof structure.
-
Product
Functional & ICT Tester
igentic® 621t
-
Growing demand for light emitting diode (LED) products and increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. The igentic® 621t is a flexible PCB tester that ensures quality while increasing production. The tester can handle multiple PCB products and test for light measurements, resistance and push button or post detection, as required.
-
Product
3 Wire (Digital) Earth Resistance Tester
4120 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.
-
Product
PXI Breadboard Module, 1-Slot, 96-Pin Micro-D
40-220A-001
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
Precision Condenser Microphone
377C10
-
Performance:Nominal Microphone Diameter:1/4"CharacteristicPressure Open Circuit Sensitivity1.0 mV/Pa1.0 mV/PaFrequency Range (2 dB)4 to 70000 Hz4 to 70000 Hz Lower Limiting Frequency (-3 dB)0.25 to 3.0 Hz0.25 to 3.0 Hz Resonant Frequency (90 Phase Shift)65000 Hz65000 HzHumidity Coefficient of Sensitivity (0 to 100%, non-condensing)0.0012 dB/%RH0.0012 dB/%
-
Product
Test Block & Plug Systems
-
Test Block system is an evolution of the 14 test circuit versions widely employed in the power utility sector. The primary difference is the incorporation of ‘finger safe’ test sockets which allow the use of shrouded 4mm banana plugs.
-
Product
Automatic Dielectric Tester
LD-LADT-A10
-
Automatic Dielectric TesterLD-LADT-A10is a fully automatic oil tester. The oil tester adopts industrial SCM to control which is applied to integrate circuit. It features anti-jamming technology which largely improves the machine capacity.
-
Product
Wafer Manufacturing
-
Scientific Computing International
A procedure composed of many repeated sequential processes to produce complete electrical or photonic circuits on semiconductor wafers in semiconductor device fabrication process.
-
Product
Low Voltage Power Supplies
-
We offer low-voltage power supplies in the power range up to 100,000W (customer-specifically even higher). , They are designed for maximum output voltages of 6.5V to 350V and are continuously adjustable from zero to maximum. Our low-voltage power supplies can be operated in constant voltage mode as well as in constant current mode. This enables unlimited operation at any time with the maximum current that can be supplied (even in the event of a short circuit). They are suitable for ohmic loads as well as inductive or capacitive loads and are characterized by a service-friendly design,
-
Product
Mobile Network Emulator
-
Qosmotec Software Solutions GmbH
QPER Mobile Network Emulator enables engineers to simulate handover scenarios in mobile networks without a fully-fledged test lab. Based on Qosmotec’s QPER technology, it allows to test UE and SIM-Card behaviour in a completely emulated mobile network: Cells can be configured with all relevant cell parameters (MCC, MNC, LAC, CI, etc.), SIMs can be added to the HLR, and UEs can use standard circuit switched and packed switched services. Thus, the QPER Mobile Network Emulator emulates the all components of a mobile network – consisting of core and radio functionality – and creates RF signals. It supports GSM, GPRS and EDGE (900 MHz, 1800 MHz) as well as UMTS (2100 MHz).
-
Product
Power Meters
-
Chroma Systems Solutions, Inc.
Chroma’s Digital Power Meters are designed for both single-phase and multiple phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits the 66200 Digital Power Meter uses state-of-the-art DSP digitizing technology. The internal 16 bits analog/digital converters with sampling rates of up to 200KHz provide both high speed and high accuracy measurements which is unprecedented within the industry for this class of power meters current on the market.
-
Product
Digital (1kV below) Insulation Tester
1651 IN
-
Standard Electric Works Co., Ltd
Microprocessor-controlled. ACV auto-detection function on 3 insulation ranges (250/500/1000V) and low Ω ragne before pressing the TEST button. 68 x 34mm large LCD display. 3½ digital LCD (2000 counts) a LCD indicated instrument for insulation(MΩ), continuity (Ω) and AC voltage. Three insulation test voltages(DC V) : 250V, 500V, 1000V. Auto ranging. Auto power off function. Auto data hold function. Rel function (ohm only). Continuity buzzer. External AC voltage warning. Automatic circuit discharge. BS 16th edition.
-
Product
DC Power Supply
CSP-3
-
● Universal power AC90~264V/DC127~380V● Build in power factor control circuit in high power model(120W~500W)● Available for series and parallel operation● To be a Back up power function with relay output in option( not available in model 20W and 24W)● RoHS & UL version in option● DIN rail mounting
-
Product
Selenium Surge Suppressor
-
Surge suppressors are used to protecting circuits from transients (sudden, brief increases in voltage). Transients of widely varying magnitudes are caused by such circuit components as motors, coils, magnets, relays, and transformers. They are found in all electrical systems and are notorious for damaging diodes, SCRs, transformers, triacs, and relay contacts.
-
Product
X-ray Inspection Of PCB Boards And More
The RTX Series
-
Glenbrook’s RTX Series of modular, real-time systems include models designed to meet a variety of production requirements including circuit board components. Numerous options make it easy to customize any RTX model to your specific application. All hardware and software elements are fully compatible to ensure the continued value of your equipment.
-
Product
Integrated Ultrasonic Level Gauge
HR9100T
-
HighReach Measuring & Controlling System Co.,Ltd
The circuit design selects high-quality power module components from the power supply part to select high-stability and reliable devices, which can completely replace the same type of imported instruments. The patented sonic intelligent technology software can perform intelligent echo analysis the debugging and the any OTHER Special the without Steps. This Technology has Dynamic Thinking at The Functions of the Analysis and Dynamic. Sound Wave at The Patented Technology of Our Company Makes at The Accuracy of at The Instrument Greatly Improved, at The Precision Liquid Level Reaches 0.25%, and IT CAN Resist various kinds of interference waves. This instrument is a kind of non-contact instrument, which does not directly contact with liquid., the instrument has a variety of installation methods. The user can use this manual to calibrate the instrument. All input and output lines Of the instrument have lightning protection and short circuit protection.
