Alternating Current
Current Alternates direction of flow cyclically. Also known as: AC
See Also: Current, Direct Current, AC
-
product
Ammeters
*Measures AC current from 1 to 2000 Amps on system voltages up to 500kV line-to-ground*Stores the last 4 readings*Dual measurement modes, peak hold and real time*Takes spot-load checks with ease*Verifies phases are balanced*Versatile for overhead and underground applications*Compact, lightweight design
-
product
Digital Multimeter
PDMT25
4000 Display CountPeak Capture ModeData HoldMax/Min Recording ModeVoltage DC: Max Range 1000 V, Accuracy +/- 0.5%Voltage AC: Max Range 1000 V, Accuracy +/- 0.8%Current DC: Max Range 10 A, Accuracy +/- 1.2%Current AC: Max Range 10 A, Accuracy +/- 1.8%Resitance: Max Range 40 M, Accuracy +/- 0.8%Duty Cycle: Max Range 99.9%, Accuracy +/- 1.2%Temperature: Max Range 760 C / 1400 F, Accuracy +/- 3.0%Frequency: Max Range 10 MHz, Accuracy: +/- 1.5%Capacitance: Max Range 40 mF, Accuracy +/- 1.5%Diode Check
-
product
Static Inverters
Our static inverters are designed as uninterruptible power supplies (inverter in conjunction with rectifier and battery) to bridge short-term interruptions, power failures, voltage fluctuations, frequency fluctuations or generally to compensate for power disturbances in the data processing sector and in automation and control systems. They are used to supply AC consumers, primarily in the rail and industrial sectors.
-
product
3-Phase AC Voltage Transducer
ENVIROMUX-PT3-600
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
product
Gauss Meters
A gauss meter displays electromagnetic wave measurements in Gauss (G), milliGauss (mG), milliTesla (mT) or microTesla (µT) units. A gauss meter can detect either static (DC) permanent (rare-earth) magnetic or dynamic (AC) electromagnetic fields (EMFs), or both. Thus, it is important to review the specifications of a gauss meter prior to purchase to ensure suitability for the intended application.Neodymium (NdFeB) permanent magnets are among the world's strongest and most widely used magnets. When testing magnets made of neodymium or other rare-earth elements, a gaussmeter or magnetometer capable of measuring DC magnetic fields is required. However, most electromagnetic fields encountered are generated by AC currents. Examples include electrical power lines, transformers and wiring for overhead lighting, solar panels and other electrical devices and equipment. Electromagnetic fields from electrical installations are believed to cause feelings of nervousness, anxiety and paranoia in EMF-sensitive human beings.Most gaussmeters offered by PCE Instruments can be calibrated and certified according to DIN ISO 9000 standards for an additional fee. Replacement gaussmeter probes and optional accessories are available for most gaussmeter models.
-
product
Measurement
AC Voltmeter
AC Voltmeter is used for measuring AC voltage. The software is capable of switching measurement modes (RMS or amplitude), but regardless of the selected mode the information about the current peak value is always displayed.
-
product
Amplifier Module
LNAM-FBX
Ultra-low-noise voltage amplifier module (LNAM) with ac coupled FET input allowing measurements between 1 Hz and 20 MHz. High gain precision and low distortion are achieved by using internal negative feedback and >1000 V/µs output stages.
-
product
Compact Digital Multimeter
PDMT08
Double-Molded Plastic HousingHigh-Contrast LCD DisplayCATIII RatedVoltage DC: Max Range 600 V, Accuracy: +/- 0.5%Voltage AC: Max Range 600 V, Accuracy: +/- 1.2%Current DC: Max Range 10 A, Accuracy: +/- 2.5%Resistance: 2 M, Accuracy: 0.8%Diode CheckContinuity TestAccessories Included: Test Leads, 9V BatteryDimensions: 5.91' H x 2.76' W x 1.89' DWeight: 8.99 oz.Sold as : Unit
-
product
LED Driver Online Tester
LEDLS-60/LEDLS-12
• The tester includes A Group Measuring Module and B Group Measuring Module. The A Group measuring module can test 6pcs LED Driver AC Parameters. The B Group measuring module can test 6pcs LED Driver AC, DC and AC/DC Parameters. • There are 12 windows to display the input and output parameters, it is good for comparing and analyses. • Quick test for all of the parameters in 0.1 seconds. • It can set up the testing parameters PASS/FAIL range, it will have Noise/Light warning if it is Fail. We also supply handle port (Extra cost) • Software communicate with PC (Extra cost)
-
product
Adhesion and Peel Tester
Test package for combination module adhesion/peel tester includes a motorized test stand, digital force gauge, AC adapter/charger for 115VAC or 230VAC, data acquisition and exporting software, scoring fixture, glue fixture and necessary attachments and cables to perform the above tests.
-
product
Electrical Test Tools
Complete offering of electrical test tools. Products include outlet testers, AC line splitters, voltage testers, circuit tracers and more.
-
product
AC Switches
Our ACST series are over-voltage protected triacs that protect themselves by folding back and leading current into the load when subjected to an overvoltage.
-
product
Cost-Effective ATE System
PRO RACK ATE
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
product
SR Series AC Reference Supplies
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 Volt excitation to Synchros or resolvers in military and industrial control applications. They accept +/- 15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6" x 3.1" x 1"H.
-
product
SCR CONTROLLED DC POWER SUPPLY
PS Series
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
product
32 Channel Optically Isolated Digital Card
104-IDIO-16
The Model 104-IDIO-16 is a 32-channel PC/104 utility board featuring 16 optically isolated inputs and 16 optically isolated solid state outputs. The isolated, non polarized inputs may be driven by either DC sources of 3-31V (or higher by special order) or AC sources at frequencies of 40Hz to 10KHz
-
product
Inverters
La Marche Manufacturing Company
This Controlled Ferroresonant transistor switching inverter design converts DC power into AC power.
-
product
Power Analyzers
Scientech Technologies Pvt. Ltd.
Scientech offers wide range of high-performance power analyzers including quality power loggers and more at the best price in India. The power analyzer is a multi-function power analyser device that measure precisely direct current, alternating current, AC-voltage, DC-voltage the intensity of DC or AC, phase rotation and idle, apparent and effective power.
-
product
High AC Current Capacitor
LC1/LC2/LC3-BN
Induction Heating Processing Equipment, Electric Current Welding, Resonant Circuits, Motor Controls; Oscillating, Bypass, Coupling circuits, High AC Current applications, High-Frequency AC Filter and Medium Frequency Power applications.
-
product
Mini Jumbo LCD Autoranging Multimeter
HH2202
High Accuracy (Basic Accuracy 1.0%). Jumbo LCD display 4000 count, 21mm figure height. Convenient Auto Ranging. Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 40MΩ. Diode test, audible continuity check
-
product
Calibration Services
Your CLIO hardware can be furnished with (or be submitted for) a SIT Certificate of Calibration. This document, produced by a laboratory accredited by the Italian Calibration Service, reports measurement data of the primary quantities generated and analyzed by the instrument (AC Voltages) traceable to National and International Standards. This document is usually requested for ISO compliance.
-
product
AC/DC Withstand Voltage Test
WB2671A/WB2671B
• Output voltage: 0-5kV (AC/DC); • Cutoff current range: AC 0~20mA (WB2671A)/0~100mA (WB2671B); DC 0-20mA; • Test time: 1-60s; • Transformer capacity: 750VA.
-
product
AC High Voltage Break Down Tester
High Voltage Breakdown Testers also known as Hipot Testers or Insulation Testers are a necessity for any Transformer testing, Substation equipment testing, Cable testing, Panel testing and testing of various insulating materials. Insulation testing is very important to ensure and maintain the safety of electrical equipments and also for the safety of operator.
-
product
Gas-insulated AC Test System
Yangzhou Power Electric Co., Ltd
The test system is used to do AC voltage withstand test and PD measurement for high voltage insulation products, combined electrical equipment, instrument transformers, etc.
-
product
3, 2 or 1 Channels, 0.5 VA, 1.5 VA or 3.0 VA
DLx
Linear Variable Differential Transformer (LVDT) and Rotary Variable Differential Transformer (RVDT) are transformer-type voltage/current transducers that convert a linear/rotary movement of a core/shaft to a multi-wire differential AC electrical signal. Both deliver signals linearly proportional to the position of a shaft (magnetic induction core). An LVDT/RVDT simulator is used to convert digital positional commands to corresponding AC signals.
-
product
Indoor Air Quality
It integrates a sophisticated thermostat with nine different internal sensors to provide an accurate real-time measurement of key air quality and air safety indicators. It is also able to control an array of devices like heater, A/C, furnaces, air purifiers and heat pumps.
-
product
Capacitor Charging Power Supplies
Excelitas Capacitor Chargers are tailored to meet your exact needs by configuring modular platforms based on proven designs. Single-phase AC input designs are capable of up to 6 kW of output power and our three-phase designs provide up to 35 kW of output power. A modular design approach results in lower cost, higher reliability, and faster time-to-market. Typical applications for capacitor charging power supplies include flashlamp pumped laser systems (Nd: YAG, pulsed lasers, dye lasers, Intense Pulsed Light Systems (IPL) and aesthetic Medical Laser Systems, Medical Holmium YAG Laser), excimer lasers, pulsed UV curing and sterilization, radar and RF systems.
-
product
Insulation Resistance Meter
AMIC-10
The AMIC-10 digital insulation resistance meter is used for direct measurements of the insulation resistance of electrical equipment working with voltage up to 1 kV. In addition, this meter makes it possible to measure compensation and protective connections, low-voltage resistance measurements and DC and AC voltage measurements.
-
product
Energy Meter
The energy meters were specially developed for measuring energy on board electric traction vehicles. You can measure both the DC and the AC signals of any existing traction power supply system (1.5kV DC, 3kV DC, 15kV / 16.7 Hz, 25kV / 50 Hz). In addition, they are also suitable for multi-system locomotives with more than one electrification system.
