Repeaters
-
Product
ResMap or DualMap Auto Load Table Top
-
Creative Design Engineering, Inc.
*Type: Table Top*Wafer load: open cassette*Wafer size: 4" to 8"*Mini Environment: N/A *Probe Changer: N/A *Aligner: N/A*Size: 12" x 28" x 10"*Range: 1m/ to 10M/*Accuracy: 0.5%*Repeatability: 0.02% *Static Repeatability: 0.1% dynamic
-
Product
Interrogator
FAZT I4G
-
The FAZT I4G Interrogator is an optical sensor interrogators. Supports multiple modes of operation including ultra repeatable performance (< 0.010pm) and fast sampling speeds 1Khz, 2Khz, 4Khz and 8Khz, spectral sensors (FP, MOF etc) and bi-refringment sensors (PM-FBG).
-
Product
Automated Testers
-
Automated test equipment creates a repeatable and efficient environment for testing your products. Innovar offers modular test equipment that easily scales with your production demands and provides redundancy to ensure continued production.
-
Product
PXI Dual 4 to 1 RF MUX SMB 75 Ohm
40-832-002
Relay
The 40-832-002 is a 75 Ohm 4 to 1 RF MUX with 2 banks in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-832 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
Hall Effect Thickness Gage
Magna-Mike 8600
-
The Magna-Mike® 8600 is a portable thickness gage that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.
-
Product
Optical Receiver Stress Test Solution
N4917BSCB
-
The Keysight N4917BSCB optical receiver test solution is a complete, automated and repeatable solution for optical receiver stress test.
-
Product
Active Transmitter & Receiver Modules
-
MAT active device transmitter modules permit the direct coupling of signals into fibers terminated with E-2000™ connectors. MAR receivers perform the reverse receiving function. Both types are carefully designed to offer a high degree of optical stability over widely-varying environmental and mechanical-stress conditions. Rugged construction ensures stable, repeatable operation over 1000 mate/demate cycles. MAT and MAR incorporate the following features: positive latching mechanism, spring-loaded shutters for eye-safety and compact footprint.
-
Product
Automatic Pull-Off Adhesion Gauge
510
-
Automatic hydraulic pump ensures smooth and continuous pressure application for consistent, repeatable adhesion strength resultsFully adjustable pull rates 0.1-1.4MPa/s (14.5-203psi) to meet National and International StandardsCan be used with 10,14.2, 20 and 50mm diameter dolliesUser definable limits with unique pressure hold and release functionUser definable measurement range with an accuracy of ±1% of full scale:10mm dolly: 100MPa (14400psi14.2mm dolly: 50MPa (7200psi)20mm dolly: 25 MPa (3600psi)50mm dolly: 4MPa (580psi)Dust and water resistant rugged design to IP64Interchangeable units: MPa, psi, Nmm2 and NA range of standard and thin substrate actuator skirts (compatible with Elcometer 506) available for adhesive strength testing on thick, thin, flat or convex substratesStore up to 60,000 readings with individual pull graphs in up to 2,500 alpha numerical batches, complete with attribute failure informationUSB and Bluetooth® data output - compatible with ElcoMaster® App for iPhone, iPod, iPad and Android mobile devices
-
Product
X-ray Fluorescence Sulfur/Chlorine-in-oil Analyzer
MESA-7220V2
-
The MESA-7220V2 measures both sulfur and chlorine in petroleum based products using the Monochromatic Energy Dispersive X-ray Fluorescence (EDXRF) method. A monochromatic X-ray source is used in order to obtain an ultra-low noise background which affords the best detection limits for both sulfur and chlorine.The detector window size was increased to collect more fluorescent X-rays and thus achieve lower level ppm values. This provides excellent, repeatable performance at both low and high concentrations of both elements.By adjusting the angle of the graphite crystal, the excitation beam can be measured to excite sulfur in the sample, increasing sensitivity.
-
Product
UV Meters
-
OAI’s UV Measurement Instrumentation are the standard for Semiconductor Lithography, MEMS, Sensors, Microfluidics, UV Curing, 3-D Printing, Sterilization, Water Purification and Solar/PVC industries. For over 45 years our meters have earned a reputation for accuracy, repeatability and dependability. We offer full calibration and support services worldwide.
-
Product
Electronic Crockmeter
TF411
-
TESTEX Testing Equipment Systems Ltd.
Electronic Crockmeter, to determine the colour fastness of textiles to dry or wet rubbing. A pinned acrylic sample holder ensures rapid sample mounting and repeatability of results. Crockmeter Fitted with a pre-determined electronic counter for strokes up to 999,999 times.
-
Product
CO₂ Sensor
STC31 (Qwiic)
-
Do you need to be able to sense CO2 concentrations of up to 100%? If so, the STC31 is the sensor for you! The Sensirion STC31 thermal conductivity sensor has two CO2 measurement ranges: 0 to 25 vol%; and 0 to 100 vol%. The measurement repeatability is 0.2 vol%, with a stability of 0.025 vol% / °C. The measurement accuracy depends on the measurement range: 0.5 vol% + 3% measured value; 1 vol% + 3% measured value.
-
Product
Winding Resistance Meter
TRM 25
-
SCOPE introduces 25 A state of the art precision winding resistance meter, specially designed for field testing as well as factory testing of large transformers up to 500 MVA. Winding resistance value of transformer and rotating machine are directly displayed on 5.7” TFT display. TRM 25 is designed to work in live EHV switchyard conditions, ensuring operator’s safety and repeatability of results. Maintenance time saving is ensured by one time connection to transformer with simultaneous resistance measurement of three / six windings, measurement of resistances of all taps with automated tap change and demagnetization facility. The meter is protected against the back-EMF offered by large inductive windings.
-
Product
Automotive Ethernet Tx Test Software 10M To 10Gbp
AE6920T
-
Unlike CAN, LIN, Automotive Ethernet demands rigorous compliance verification using test cases that cover transmitters (Tx), receivers (Rx), and harness/connector assemblies. To help you save time and effort, Keysight offers solutions that automate the testing and validation across Transmitter (Tx), Receiver (Rx), and the connections between Automotive Ethernet devices. Our engineers have invested thousands of hours in learning the standards and creating automated, repeatable compliance tests. These proven applications help you ensure proper test configuration and valid measurement results. Ultimately, you’ll have greater confidence that your device is compliant. Now available for data rates up to 10Gbps. The automotive Ethernet test solution AE6900T offers hardware and accessories to make sure you have all of the components you need to get up and running quickly.
-
Product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
-
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Low PIM Coaxial Switch, DC to 20 GHz, Matrix
87406Q
-
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87406Q is a low PIM matrix coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency and ultimately maximizes test throughput.
-
Product
Ensure Accurate Screening, Diagnosis & Monitoring
Ultrasound QA Solutions
-
Gammex is the only ultrasound QA solutions manufacturer with expertise in medical physics since 1969.The 156 phantom helped establish the mammography repeatability and reproducibility standard: any mammography technologist (radiographer) at any time, on any machine, can provide the same image set to help detect breast cancer.We collaborated with clinical and academic thought leaders to develop our patented HE Gel and the first portable Doppler Flow phantoms in the world. HE (High Equivalency) Gel is what sets Gammex ultrasound products apart; it helps ensure all your transducers and system settings are fully tested across the entire frequency range from 2 to 18 MHz. Our HE Gel combined with our medical physics and quality control expertise gives you confidence with consistent diagnostic image quality in clinical applications.
-
Product
Clamp-On Ultrasonic Flow Monitor
KATflow 10
-
The KATflow 10 is a simple ultrasonic clamp-on flow monitor, which provides an extremely cost-effective alternative to in-line flowmeters on effluent, wastewater and sludge applications. The KATflow 10 is used to monitor the flow of liquids containing higher levels of solids or entrained gas bubbles for measurements where a general flow indication is sufficient. The instrument is extremely simple to install and commission and is ideal for applications which demand good repeatability and reliable results.
-
Product
Environmental Control System Test Platform
Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
Geo Analyzer
ElvaX Geo
-
Instant on-site elemental analysis is one of the necessities of the modern mining industry. ElvaX Geo offers you accurate data and ease of operation during geo exploration or quality assurance. The instrument is designed specifically for long non-stop convenient operation. The unique 800 mm2 analytical spot analysis increases averaging of inhomogeneous samples. A composite pole helps you keep a comfortable body position during operation and enables you to analyze hard-toreach places. This form factor allows for uninterrupted measurement during slow walking while measurement results are communicated to the operator through headphones. ElvaX Geo is operated through a PDA in a protective enclosure, which can be put underneath outer garment in case of extreme climatic conditions. The Li-Ion Battery can be hidden as well. ElvaX Geo software uses both the Fundamental Parameters and the Empirical Calibration Methods. Fundamental parameters analysis of unknown samples without empirical calibration is remarkably accurate. However every instrument is calibrated for the basic mineral types with NIST or NIST traceable samples. ElvaX Geo demonstrates excellent limits of detection and repeatability.
-
Product
UV Analyzer
AF45
-
The AF45 is a high precision UV light absorption analyzer designed for inline operation to provide accurate concentration measurements with remarkable repeatability, linearity and resolution. Wavelength and optical path length are individually configurable for extremely high accuracy to meet process control requirements.
-
Product
Magnetizing Power Supply
-
This is a magnetizing power supply which can be used even in areas (countries) with an unstable electricity supply.The accuracy of the repeating magnetizing voltage enhances our reputation for top-class quality in the industry.We confirm the peak value, the time of electrification, and the electrical current area by using an impulse meter (a highly accurate magnetizing ammeter) before we ship out the products.
-
Product
4-Port Coaxial Switch, DC to 18 GHz
8763B
-
The Keysight 8763B offers excellent electrical and mechanical performance with broadband operation, high isolation, low SWR, long life, and exceptional repeatability.
-
Product
Coaxial Switch, DC to 18 GHz, SPDT, 24 to 30 V Solenoids
8761B
-
The Keysight 8761B is a single-pole, double-throw coaxial switch with excellent electrical and mechanical characteristics for 50 ohm transmission systems operating from dc to 18 GHz. It features broadband operation, long life, low SWR, excellent repeatability, and magnetic latching solenoids. The Keysight 8761B switch is small and lightweight, making it ideal for applications where space is limited. Because of its versatility and excellent electrical performance, it is well suited for automated testing and systems applications.
-
Product
Signal Generator
-
An electronic device that generates repeating or non-repeating waveforms used to test and evaluate electronic test equipment.
-
Product
Temperature Measurement
-
Describes the process of measuring a current local temperature for immediate or later evaluation. Datasets consisting of repeated standardized measurements can be used to assess temperature trends.
-
Product
Authorized GPS AES M-Code Testing
SimMCODE
-
Validate M-Code functions via AES M-code protocols for high fidelity secure testing. In order to facilitate greater accuracy and robustness than available in civilian GNSS, the US government has long provided secure signals for authorized users. M-Code is the latest iteration of this process, providing an encrypted and standalone service (unlike the P(Y)-Code). Spirent’s SimMCODE enables authorized users to thoroughly test Military GPS User Equipment (MGUE) in repeatable, lab-based environments, using the commercial encryption algorithm, Advanced Encryption Standard (AES).
-
Product
Fully-Programmable Automatic Stencil Printer
MC1400
-
MC1400 Automatic stencil printer MC1400's automatic dual-vision alignment system ensures accuracy while the printer's linear-guided movements and vertical stencil separation provide high precision and repeatability, a combination that results in ultra-fine-pitch printing capability for component pitches down to 0.3 mm (12 mil). With quick setup and changeover, thanks to the flexible mounting table, MC1400 stencil printer easily keeps pace with medium to high volume production lines and is well-suited to precision batch printing.
-
Product
Low cost EDXRF Elemental Analyzer
NEX QC+ QuantEZ
-
Applied Rigaku Technologies, Inc
As a premium low-cost benchtop EDXRF elemental analyzer, the Rigaku NEX QC+ QuantEZ delivers wide elemental coverage with easy-to-learn Windows®-based QuantEZ software. Non-destructively analyze from sodium (Na) through uranium (U) in almost any matrix, from solids and alloys to powders, liquids, and slurries. The 50 kV X-ray tube and Peltier cooled silicon drift detector (SDD) deliver exceptional short-term repeatability and long-term reproducibility with excellent element peak resolution. This high voltage capability, along with multiple automated X-ray tube filters, provides a wide range of XRF applications’ versatility and low limits-of-detection (LOD).
-
Product
Meters For Contact Angle And Surface Tension
Contact Angle Standard
-
Optik Elektronik Gerätetechnik GmbH
The contact angle standard is a glass plate with images, representing sessile drops with different contact angles. The contact angle standard is manufactured by a high accurate lithographic process, so the images itself are very accurate according the given CAD-data. The Glass plate is placed on the measuring table instead of a real drop. The proof of the reproducibility of the contact angle measurement is performed by a repeated measurement of the object (sessile drop). For a correct test, the measurement must be performed, using the live video (not a frozen image). For a real sessile drop exists the problem, that it evaporates permanently. The result of the permanent evaporation is the permanent change of the contact angle. Therefore, the proof of the reproducibility of the contact angle measurement is not possible, using a real liquid, since the object changes permanently the contact angle!
