Link
See Also: Camera Link
-
Product
PCIe-1437, 80-Bit Camera Link, PoCL-Compatible Frame Grabber Device
785605-01
Frame Grabber
The PCIe-1437 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PCIe-1437 includes an onboard FIFO for higher bandwidth use cases, and it works with any base‑, medium-, and full-configuration Camera Link camera. The PCIe-1437 is ideal for many industrial, life science, and biomedical imaging applications. The PCIe-1437 also supports Power over Camera Link (PoCL) and can power cameras through PoCL-enabled cables.
-
Product
VME64 to USB 2.0/Optical Link Bridge
VX3718
-
The VX3718 is the new VME to USB 2.0/Optical Link Bridge that fully replaces the VX1718 (VME-USB) and V2718 (VME- CONET) models. The Bridge Implements a VME master controlled by a PC via USB 2.0 and Optical Link (CAEN CONET protocol) including all the functions of its two predecessors in a unique device.
-
Product
NI-1483, Full-Configuration Camera Link Adapter Module for FlexRIO
781341-01
Module
The NI‑1483 makes FPGA image processing possible for FlexRIO systems. It supports 80‑bit, 10‑tap base‑, medium‑, and full‑configuration image acquisition from Camera Link 1.2 standard cameras. You can pair the NI‑1483 with a PXI FPGA Module for FlexRIO to perform custom image analysis. FPGA processing is ideally suited for applications that require bit-level processing and very low system latency. Implemented in hardware, FPGA processing does not require CPU intervention. You can process images on the FPGA independently or with a CPU for more advanced preprocessing architectures.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787455-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
OBD II Data Link Connector Breakout Box & Diagnostics Software
Mr. BOB DLC
-
Automotive Diagnostics and Publishing
Mr. BOB DLC OBD II Data Link Connector Breakout Box & Diagnostics Software for Network Waveform Viewing. This OBD2 breakout box with 8 Graphing Meter Scope like channels, is designed for the OBD2 DLC data link connector. Includes OBD II protocols such as PWM, ISO, KWP2000, 9151, J1850, VPW and CAN.
-
Product
PCIe-1433, Base-, Medium-, Full-Configuration Camera Link, PoCL Compatible Frame Grabber Device
781169-01
Frame Grabber
The PCIe‑1433 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PCIe‑1433 includes an onboard … FIFO for higher bandwidth use cases, and it works with any base‑, medium‑, and full‑configuration Camera Link camera. The PCIe‑1433 is ideal for many industrial, life science, and biomedical imaging applications. The PCIe‑1433 also supports Power over Camera Link (PoCL) and can power cameras through PoCL‑enabled cables.
-
Product
Fully Automatic Close Link Single Phase Energy Meter Test bench
SY 8125
-
Hong Kong Songyang Industrial Ltd.
The devices are fully made by aluminum alloy materials and the table board is composed of fireproofing and heat-proof materials. The output voltage and current use soft startup and stop. It has the protection functions of voltage short circuit, current open circuit and power amplification exception. The device has the features of high stability, good reliability and large output power
-
Product
Development System
FE-51CC01
-
* Emulates Atmel T89C51CC01/2 and T89C51AC2, T89C5115 * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Aurora®
-
The Aurora® electromagnetic tracking solution provides unobstructed real-time tracking of micro sensors that can be embedded into rigid and flexible OEM medical instruments such as ultrasound probes, endoscopes, catheters, guidewires – even at the tip of a needle. With the Aurora® electromagnetic tracking solution, no line-of-sight is needed for in-vivo tracking of instruments through twisting anatomical tracts. When integrated as a component into the workflow of OEM image-guided surgery or interventional systems, the Aurora acts as the link between patient image sets and 3D space, enabling the instruments’ positions and orientations to be instantly localized and visualized within the operative field. It does so with the exceptional speed, accuracy, and precision required by today’s most demanding minimally invasive approaches.
-
Product
Guzik Signal Analyzer
GSA 6000 Series
-
Works with Read-Write Analyzer RWA 4000. Guzik Signal Analyzer (GSA) 6000 series combines high-speed waveform digitizer with built-in digital signal processing hardware and high-speed data transfer link to a computer. The Signal Analyzer comes in a space-saving display-less 2U 19” rack-mounted form factor.
-
-
Product
RF Planing & Optimization Software
Atoll
-
Atoll is a scalable and flexible multi-technology network design and optimisation platform that supports wireless operators throughout the network lifecycle, from initial design to densification and optimisation. Supports: GSM / GPRS / EDGE, UMTS / HSPA, CDMA2000 1xRTT/EV-DO, LTE, TD-SCDMA, WiMAX / BWA, Microwave links.
-
Product
PXI 2A Multiplexer, 1-Bank, 64-Channel, 2-Pole
40-614B-016
Multiplexer Module
This 1-bank, 64-channel, 2-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Telemetry Bit Error Rate (BER) Tester
-
Reach Technologies Inc. Bit Error Rate Testers are designed for testing synchronous serial communications equipment, communications links and radio telemetry systems. In addition to several standard configurations, Reach also offers custom configurations, including multi-channel and mixed data rates.
-
Product
Remote Radio Head
CMPHEAD
-
The separate one-box tester and the R&S®CMPHEAD30 RRH concept allow short RF cable lengths for an optimal link budget in radiated test environments. This approach enables testing of fully assembled FR2 devices and RFICs with both IF and mmWave RF interfaces. The multi-band R&S®CMPHEAD30 covers all important FR2 bands
-
Product
Gas Analyzers
-
Independent Handheld 5 Gas Analyzer or use with MODIS™ Link, VERDICT® and VERUS® Bluetooth® link. Fully Portable 5 Gas Analyzer, go anywhere, use anywhere 110 V AC and 12 V powered Internal rechargeable battery, up to one hour of use Ideal for road testing and mobile use Measures exhaust emissions for CO, CO2, HC, O2, NOx and AFR/Lambda Provides an instant assessment of an engine vehicle exhaust and catalytic converter MODIS, VERDICT® and VERUS® Link for enhanced real-time viewing Setup required with included software on USB stick Gather all the evidence required for effective and accurate vehicle diagnostics on one screen in real time View, graph, save and recall data Monitor and reduce vehicle emissions, improve driveability and fuel efficiency There are 255 memory locations in the analyzer to track and print data for the same or many different vehicles Compatible with gasoline, CNG, propane and diesel fuel types Annual calibration and sensor replacement performed at Crystal Lake Northern Repiar enter Meets required industry standard
-
Product
Crowbar Resistors
-
Crowbar resistors are three phase resistance banks which are connected to the rotor windings of the DFIG (Doubly-Feed Induction Generator) such as wind power generator. They are used to prevent damage to the inverter circuits attached to rotor side when a fault occurs in the grid. DFIG power converter, which has a restricted over-current limit, needs special attention during faults in the grid. If the rotor current or DC link voltage reaches the threshold value, crowbar resistors disconnect the converter in order to prevent the generator turning into a squirrel cage induction machine. By crowbar resistors, the DFIG could stay connected to the grid and continue its operation.
-
Product
Transmitter Control Subsystem (TCS)
Loran C Accufix 7500
-
USCG Loran Transmitter Control and Display stations modernized and upgraded to state-of-the-art processor controlled technology. Fully redundant system with comprehensive built-in performance monitoring. Automatic switchover upon detection of error, high single point failure tolerance. Long distance communications link supports remote station operation on a continuous basis. Built-in fault detection and monitoring enables dynamic re-allocation of failed subsystem modules, and fault isolation to major replacement assemblies.
-
Product
3U PXI Express Board
SMT709
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
DVI Extender with IR and Stereo Audio Options via One CAT5/6/7
ST-C6DVI-300
-
The XTENDEX® DVI Extender transmits digital DVI video up to 300 feet away from a DVI source over a single CAT5/6/7 cable. Each video extender consists of a local unit that connects to a single link digital DVI source and optional IR emitter, and a remote unit that connects to a DVI display and optional IR receiver.
-
Product
Industry Products
-
China Sheenrun Electronics Co.
The forest fire prevention video monitoring and early warning management system is based on front-end monitoring equipment and video encoders, adopts a C/S architecture, and sends data and information to all areas in the service area through the network and other transmission links in the interactive area. Kind of server. The client in the business area manages and processes the monitoring business. The figure below is a schematic diagram of the system architecture.
-
Product
Mini Hardened Media Converter, 100Mbps, LFPT, SFP
IMC-350I-SFP
-
Metal enclosure with compact sizeIndustrial grade design that supports an extended operating temperature(IMC-350I series)IEEE802.3af compliant (IMC-350I series as PoE-PD)Supports Link Fault Pass Through (LFPT)Centralized powered IMC-318I chassis
-
Product
PXI 2A Multiplexer, 4-Bank, 4-Channel, 8-Pole
40-614B-009
Multiplexer Module
This 4-bank, 4-channel, 8-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Two-Way Time Transfer (SWSTFT) Satellite Time and Ranting Equipment (SATRE)
TWSTFT
-
- 1 – 3 receiver channels- Automated measurements- Operates unmanned, 24 / 7- Remote control over TCP/IP- Data transfer via TWSTFT link from remote site- Sub-nanosecond precision TWSTFT with real time results- Internal measurement database for the last three months on a one minute basis
-
Product
Satellite Trunk Interception System
-
Satellite trunks in the X, C, Ka, Ku bands carry enormous information, the interception of which can assist LEAs with real-time analysis of data transmitted over these links. Our solutions are customizable and scalable (Bands and protocols) based on the customer's needs.
-
Product
Thermal/Multi-Function Data Logger
51101
-
Chroma Systems Solutions, Inc.
Models with 1, 8, and 64 channels on-line data recording. Multi-sets linked to a PC for hundreds of channels are doableSupports B, E, J, K, N, R, S, and T type thermal couples with ITS-90 defined temperature rangeIndividual channel cold junction compensation withTemperature resolution up to 0.01℃, error down to (0.01% of reading+0.3℃)Voltage full range ±480VDC, ±10VDC; resolution 1mV, 10uV; error down to (0.1% of reading+1mV), (0.015% of reading+100uV)1000VDC channel to channel isolation, full protection for testing points with charge and guarantee for accurate measurementsThermal couple open circuit detectionPC-based operation with powerful software for recording and analyzing data1 and 8 channel models are USB powered. No battery or external power supply is required
-
Product
SampleStation And AuraSolution: Automated Analysis Software For MALDI-8020
SampleStation and AuraSolution
-
The SampleStation and AuraSolution software link to the MALDI Solutions MALDI-8020 control and analysis software to analyze samples automatically based on a worklist.
-
Product
Compute Express Link (CXL)
-
Compute Express Link (CXL) is a new high-speed CPU-to-Device and CPU-to-Memory interconnect designed to accelerate next-generation data center performance. CXL technology maintains memory coherency between the CPU memory space and memory on attached devices, which allows resource sharing for higher performance, reduced software stack complexity, and lower overall system cost. This permits users to simply focus on target workloads as opposed to the redundant memory management hardware in their accelerators. CXL is based on a PCI Express 5.0 Physical layer with speeds up to 32GT/s. Teledyne LeCroy provides protocol analysis test equipment to support development and debug of CXL based devices.
-
Product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787456-01
Interface
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a … high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
Product
Multifunction Handheld SM MM OTDR
X2100
-
X-2100 series OTDR is manufactured with patience and carefulness, following the nationalstandards to combine the rich experience and modern technology, subject tostringent mechanical, electronic and optical testing and quality assurance; inthe other way, the new design makes X-2100 more smart and compact andmulti-purpose. Whether you want to detect link layer in the constructionand installation of optical network or proceed efficient maintenance andtrouble shooting, X-2100 can be your best assistant.
