Link
See Also: Camera Link
-
product
Transceivers
Transceivers implement physical layer protocols for various communications and serial bus interface standards. Maxim’s transceivers integrate a wide array of features to increase reliability and simplify designs while providing the highest levels of protection on the market. Click on the following links for more information about each of our transceiver product lines.
-
product
Mini Fiber Optic, Contact, ITA, Multimode
610113173
* This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113172. (May mate with other Receiver contacts, as well.)
-
product
PCI Express 2-Port
7203e
The 7203e PCI Express serial interface provides two optically isolated serial ports, each individually configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C952 UART with 128-byte Tx/Rx FIFOs that enables data rates to 460.8K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
LGA 1151 Intel® Xeon® E3 v5/v6 & 6th/7th Generation Core™ ATX Server Board with 4 DDR4, 4 PCIe, 3 PCI, 6 USB 3.0, 6 COM, 6 SATA3, Quad/Dual LANs, IPMI
ASMB-785
- Supports LGA 1151 Intel® Xeon® E3-1200 v5/v6 and 6th/7th Generation Core™ i7/i5/i3 processors- DDR4 2400/2133/1866/1600/1333 MHz ECC/Non-ECC UDIMM up to 64 GB- One Gen 3.0 PCIe x16 link (or two PCIe x16 slots with x8 link), two PCIe x4, and three PCI slots- Triple display - two DVI-D and one VGA ports- Supports up to ten RS-232 or six RS-232 and four RS-422/485 ports- Rackmount optimized placement with positive air flow design- 0 ~ 60 °C ambient operation temperature range
-
product
PXI/PXIe High Density 2A Multiplexer, 26-Bank, 4-Channel, 1-Pole
42-614D-023
The 40-614D-023 (PXI) and 42-614D-023 (PXIe) 26-bank, 4-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Software
Active Silicon computer vision products are supported by a variety of software tools. We provide powerful user software and SDKs for CoaXPress and Camera Link frame grabbers with support across several operating systems. Additionally, a wide range of drivers for third-party machine vision and scientific imaging packages is available.
-
product
Battlefield Operations Support System
TCG BOSS
Curtiss-Wright Defense Solutions
TCG BOSS is the industry’s most complete, reliable, easy-to-use, and cost-effective TDL testing and platform integration solution on the market that provides support for multiple terminals and interfaces and adheres to industry data link standards.
-
product
Residential/Commercial Combustion Analyzer Kit w/ Printer
C165+KIT
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C165+ Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to optional printer and wireless App. The new LINK feature connects the included wireless pipe clamp temperature probes and other optional probes to the C165+. Essential information for installing and maintaining furnaces and boilers all in one device.
-
product
CL LX1 Base Frame Grabber
Xcelera-CL LX1 Base
Building on the field proven technology and performance of DALSA’s X64 frame grabbers, the X64 Xcelera™ Series leverages the PCI Express (PCIe) platform to bring traditional image acquisition and processing technology to new levels of performance and flexibility.The PCIe point-to-point host interface allows simultaneous image acquisition and transfer with little intervention from the host CPU.The X64 Xcelera -CL LX1 Base is a cost effective frame grabber based on the PCI Express x1 interface. Fully compliant with Camera Link (V. 1.20) specifications, the Xcelera-CL LX1 supports single Base cameras and can acquire images from a wide variety of multi-tap area and line scan, color and monochrome cameras.
-
product
Compact Unmanaged Ethernet Switch
ML600
The MultiLink ML600 is a Compact Unmanaged Ethernet Switch that is ideal for Industrial Facilities, Substations, and Transportation environments that have few Ethernet devices in one location. As a very cost effective solution, the ML600 will supply you with high speed networking in your harsh environments and is equipped with Link Loss Learn (LLL) that allows for use in redundant architectures thus ensuring you will always have access to your devices.
-
product
PCI High Density Matrix, Single 22x4 2-Pole
50-510A-022
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
product
Enterprise/ Carrier Transmission Tester
UniPRO MGIG1 Series
Designed for comprehensive turn-up testing, monitoring and troubleshooting of fixed line, mobile, microwave and wireless carrier Ethernet links. UniPRO MGig1 is suitable for use on any backhaul link at speeds of up to 1 Gb/s.
-
product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 8-Channel, 8-Pole
40-614D-013
The 40-614D-013 (PXI) and 42-614D-013 (PXIe) 2-bank, 8-channel, 8-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Heat Recovery Steam Generators
The heat recovery steam generator (HRSG) provides the thermodynamic link between the gas turbines and steam turbines in a combined-cycle power plant. Each HRSG solution is custom-engineered to meet your desired operating flexibility and performance requirements. With more than 750 HRSGs installed worldwide, GE is a world leader in supplying HRSGs behind all major OEM’s gas turbines.
-
product
PXIe High Performance System Module with Connectivity Expansion: Dual Port (x16), Gen 3
M9024A
The M9024A is a PXIe System Module and is installed in the system slot of a PXIe chassis. When combined with an appropriate host adapter, it will provide a high data BW connection between the host PC and the chassis. The M9024A has a flexible configuration capability. Each card has two Gen 3 x8 PCIe cable links capable of achieving speeds up to 8 GB/s on each port. These two ports can be combined into a single x16 cable link providing a speed of up to 16 GB/s. This means a data-intensive system can be built using high-performance desktop or rack-mounted computers.
-
product
PXI 2A Multiplexer, 2-Bank, 64-Channel, 1-Pole
40-614C-010
This 2-bank, 64-channel, 1 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
- Optical / RF Converter
OPT 80
Calibrated measurement of the optical power of satellite and terrestrial TV signals distributed in optical fiber Calculation of optical signal losses on distribution Measurement of digital parameters (BER - MER - NM etc.) of optical signals converted into RF Visualization of optical carriers in RF Field Metric Spectrum Analyzer Power Meter Optical Field Meter Display Optical RF Power Supply Line Link Meter (LNB power supply ) Optical LNB power supply 13V 500mA with short circuit and overload managementAcquisition of optical measurements using the field meter Data Logger Option: certification of the OPT80 calibration and optical power measurements
-
product
Serial-to-Daq Minibox
Model 2367
* 2367 provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Module. * DB-25 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * The 2367 is packaged in a CE approved Minibox™ metal case to minimize EMI/RFI. * 1 U high Rack Mounting Kit mountsone or two 4867s.* Plug-on Terminal Board simplifies wiring connections.* Includes Universal Power Adapter and 62-pin mating connector.
-
product
EXG X-Series Microwave Analog Signal Generator, 9 kHz to 40 GHz
N5173B
Balance budget & performance to address parametric testing of microwave components & receiversPerform LO up conversion for microwave backhaul links or CW blocking for receiver testingMaximize test throughput with 600-s frequency switchingCharacterize microwave filters & amplifiers with the best combination of output power, low harmonics & full step attenuationUse as a high-stability system reference: the standard high-performance OCXO has an aging rate of 5x10-10 parts/day
-
product
Audio Analyzer
LA100
The LA100 Audio Analyser is a complete audio test system in daily use world-wide by broadcasters, manufacturers, telecom and studio engineers. The flexibility of the system means that testing a broadcast satellite link or aligning a Beta cam machine is as easy as testing a loudspeaker or studio intercom. The LA100 comprises the LA101 Audio Oscillator and the LA102 Audio Measuring Set.
-
product
Optical Transmitter
ST1550I
Hangzhou Softel Optic Co., Ltd.
When ST1550I Optical Transmitter is applied in the multi-channel transmission, the laser’s chirp effect will react with the link dispersion of the fiber. There will be distortion other receiver. If working with the EDFA, there will be serious CSO deterioration. The distortion and deterioration will increase with the longer distance and more channels. 1550nm internal modulation CATV optic transmitter, has the chirp and dispersion compensation inside, and improves the system index greatly. It can be used in the town where the fund is shortage and the distance is less than 10Km as a transition solution.
-
product
3-Component Quartz Force Rings And Links
Three-component dynamic force sensors are offered in both ICP® and charge output configurations for dynamic and quasi-static force measurement applications. Each utilizes an array of precision aligned, quartz sensing crystals. Measurements along the z-axis are proportional to applied compression, tension and impact forces. Measurements along the x and y axes are proportional to shear forces that are imposed upon preloaded crystals by the test fixture.
-
product
STAR Fire Mk3
The STAR Fire Mk3 is a test and development unit that can emulate, stimulate, debug and validate SpaceFibre enabled equipment. The STAR Fire Mk3 can transmit and receive both SpaceWire and SpaceFibre traffic; it can interconnect SpaceWire equipment to a SpaceFibre network; and it can operate as a SpaceFibre link analyser, capable of unobtrusively capturing and displaying SpaceFibre traffic. MICTOR connectors on the rear of the unit allow decoded SpaceFibre signals to be viewed on an external logic analyser. Integration with external equipment is possible using SMB connectors.
-
product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 32-Channel, 1-Pole
42-614D-006
The 40-614D-006 (PXI) and 42-614D-006 (PXIe) 4-bank, 32-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Lab Power Supplies
SYSKON Series
The analog interface is equipped with two programmable trigger inputs and three signal outputs, which can be linked to various device functions for indication, or for controlling external devices and an auxiliary power output. Beyond this, monitor outputs and control inputs for voltage and current setpoints are available as well. Sensing leads allow for auto-sensing operation at the power consumer. Strict menu-driven operation supports highly diverse programming functions. The device is transformed into a freely programmable test signal generator by means of an expanded sequence memory and extra functions.
-
product
Desktop Test Interface Station
2210
TESCO’s new Desktop Test Interface Station (Catalog No. 2210) provides metering professionals with exceptional testing flexibility. The Test Interface Station is ergonomically designed for meter technicians working in a lab or a desktop, yet still rugged for field use. The Test Interface Station includes a zero insertion force (ZIF) meter socket, voltage selection, form selection, open/closed-link selection and bi-directional cabling to power a load box/test kit & connect test standard potentials. When combined with a test kit/test standard and powered via 120 VAC, the Test Interface Station creates a single position, stand-alone, meter accuracy testing device for various socket based meters (both mechanical & solid-state).
-
product
Satellite Interception system
Shoghi has designed and developed various solutions to passively intercept traffic (Voice, Fax and Data) from Global Mobile Personal Communications by Satellite (GMPCS) and point to point satellite communication networks.All solutions are fully integrated monitoring and analysis platform which enables acquisition, processing, storing and analysis of Voice, Fax, Data and High speed IP traffic.To challenge the various monitoring scenarios Shoghi has designed both tactical and strategic solutions equipped with automatic post processing, decoding demodulation and decryption of intercepted Voice, Fax, Data and High speed IP traffic.Our GMPCS Satellite monitoring solutions are capable of intercepting Voice, SMS, Fax and Data traffic along with Call Related Information and Geo-location from Thuraya-2, Thuraya-3, ISAT Phone Pro, Iridium satellite networks.The point to point satellite communication monitoring systems are capable of intercepting traffic including Voice, Fax and Data from C and Ku-band satellite carriers from Intelsat, Eutelsat, Arabsat, Turksat etc. The Satellite Monitoring system can also process and decode GSM traffic on satellite and decode high speed IP traffic online.1.Satellite Monitoring Solutions:2.Satellite Carrier Analysis System3.C/Ku Band Satellite Monitoring4.DCME Analysis System5.GSM Abis Link Monitoring Module6.IP Link over Satellite Monitoring7.Satellite Carrier Reconnaissance and Analysis System8.VSAT Monitoring System9.Satellite Terminal Geolocation System
-
product
Framework for Soft-Error Protection
RobustScan™
RobustScan™ provides a platform for users to pick patented Configurable Soft-Error Resilience (CSER) cells or their preferred SER mitigation cells. First, Soft-Error Rate (SER) analysis is performed. Then it performs automatic robust-scan-cell and hardenedcombinational- cell selection and synthesis. Finally it generates verification testbenches for the final design. RobustScan™ can be used with scan chains inserted using third-party tools; it can be linked to third-party�s SER analysis programs and is fully compatible with SynTest�s existing DFT tools for test, debug, and diagnosis.
-
product
Xtium Frame Grabber Family
The Xtium series delivers higher bandwidth to sustain Camera Link 80-Bit modes over longer cable distances and supports a wide variety of area and line scan color and monochrome cameras, all in a compact, single slot solution.
-
product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 8-Channel, 16-Pole
42-614D-019
The 40-614D-019 (PXI) and 42-614D-019 (PXIe) 1-bank, 8-channel, 16-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.





























