Interconnects
Links between systems, networks,nodes, equipment, devices, components and circuits.
See Also: Mass Interconnect, Connectors, Cable Assemblies, Interfaces
-
Product
USB Type-C Interconnects Compliance Test Software
S94USBCB
-
Use the S94USBCB software to test, debug and characterize your USB Type-C cable and connector designs. The PathWave TAP based test sequencer automates the network analyzer (VNA) for each test and generates a comprehensive HTML report. When run with L8990M switch matrix, it enables 20-ports fully automated test without port re-connection.
-
Product
DC Coupled Differential Switching System
BS1553F(X)
-
Universal Switching Corporation
The BS1553F(X) is a modular passive DC coupled differential switching system. It is designed as an automated "patch panel" for interconnecting numerous MIL-STD-1553 devices, cables and hardware, or for routing other differential signals such as '422 clock/data or kelvin ATE measurements. The I/O capacity is scalable from a small 8x8, up to 64x64 in one 5RU unit.
-
Product
Connect Generators to the Grid
GridCode
-
DIgSILENT has developed a new verification tool called DIgSILENT GridCode. The software has been designed in response to the need to verify whether a conventional or renewable power plant is compliant with local Grid Code interconnection requirements on basis of generating unit tests. There is a new trend towards verification of requirements at the point of interconnection of a power plant using transient stability simulations with numerical models. An increasing number of Transmission System Operators are including model validation methods to quantify the risk and uncertainty when using these simulation models in stability studies. These new methods have been included in the DIgSILENT GridCode tool.
-
Product
Software
D2B
-
The unique capabilities of Teradyne's D2B software enable EMS and OEM manufacturers and partners to interconnect their global enterprises to optimize printed circuit board assembly test and inspection efficiencies early in the manufacturing / build cycle. D2B is a powerful suite of solutions that provides a standards-based architecture that supports GenCAM and ODB++ file formats enabling electronic manufacturers to outperform their competition, maximize profitability, and get to market first.
-
Product
Switch Probes
-
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
Product
Cable Assemblies
-
Teledyne Storm Microwave, an industry leader in providing advanced cable assemblies and interconnect products around the globe, has a long and proud heritage serving domestic and overseas defense and telecom markets since 1978.At Teledyne Storm, we manufacture our flexible and semi-rigid coax cable in-house leveraging the highest quality, state-of-the-art equipment and processes. Flexible cable assemblies through 50 GHz are engineered and stringently tested to meet the most demanding requirements for Low Loss, Phase Stability, Durability, and Miniaturization.
-
Product
Intermittent Fault Detection & Isolation System
IFDIS
-
The IFDIS™ uses patented Intermittent Fault Detector technology that simultaneously and continuously monitors every circuit path within a Unit Under Test (UUT) - such as a Line Replaceable Unit (LRU) chassis' interconnects - for intermittent continuity failures that occur for as short as 50 nanoseconds. This state of the art technology is combined with an environmental chamber and vibration table, which simulate the UUT’s operational environment and cause intermittent faults to manifest, creating a system that is unsurpassed in intermittent fault detection.
-
Product
24-Port PCI Express
PEX 8796
-
The ExpressLane™ PEX8796 is a 96-lane, 24-port, PCIe Gen3 switch device developed on 40nm technology. PEX8796 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
eDAK For MAC Panel
JT 2147/eDAC for MAC Panel
-
The JT 2147/eDAK is a new variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within a MAC Panel ‘Scout’ mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry plus four independent, programmable TAP modules (two of type JT 2149 and two of type JT2149/MPV) on a single board that matches the MAC Panel Direct Access Kit (DAK) form factor. Overall this configuration offers four Test Access Ports, 64 Digital IO Scan channels and reconfigurable (SCIL) capabilities
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UUT 586 x 248 mm
MG-03-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 248 mm (wxd)• Outer dimensions: 750 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
Product
9050 Rack Mount
-
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
-
Product
Circbord
8023
-
VECTOR Electronics and Technology, Inc.
3-hole solder pad for interconnecting multiple component leads. I/O area with square solder pads for connectors mounting. Circuit pattern etched onto both sides. Double sided with plated thru holes. Solder mount DIP sockets or IC devices with any lead spacing.
-
Product
PC104 Switches
-
Curtiss-Wright Defense Solutions
Our PC104 switches provide systems integrators with a fast and powerful way to interconnect chassis, cards, and CPUs through switched Fast and Gigabit Ethernet links. These PC/104 Ethernet switches, optimized for size, weight, and power (SWaP)-sensitive embedded military and civilian computer network systems applications, enable reliable local area network (LAN) switching in extended operating temperature ranges and extreme shock/vibration environments.
-
Product
BGA SMT Adapters
Giga-snaP™
-
Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapter line of products provide an inexpensive and reliable method for attaching BGA chips to target board. The product line consists of patented female sockets with machined pins epoxy over-molded into an assembly that matches a particular BGA pattern. The epoxy over-molded female BGA socket is soldered to a PCB using standard soldering methods. A corresponding male pin BGA adapter, to which the user attaches their BGA chip, is plugged into the female socket on the board thus interconnecting the chip and the system is ready to go. The SMT adapters have the same solder ball types as the chips they are emulating. These adapters have less than half of the insertion force of competitive adapters, shorter electrical path for highest speed, and can be solder reflowed numerous times. A complete description and drawings of Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapters can be found at the tables shown below.
-
Product
Connectivity & Products
-
Enabling better, safer products and services in a more interconnected world.
-
Product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 26-30 AWG
610138112
Signal Contact (ITA)
Primary mating contact 610138116. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.
-
Product
Advanced Voice Quality Assurance System
AVQA
-
R&S®AVQA is a non-intrusive voice assurance system that provides many integrated monitoring functions for ATC communications systems. These functions include:Quality assurance reports to CAAType acceptance of new IP systemsLive information about disturbance to ACC adminVoice quality report on ANSP interconnection (e.g. NewPENS)Network quality reporting
-
Product
PCI-8516, 2-Port, PCI, LIN Interface Device
781365-01
LIN Interface
2-Port, PCI, LIN Interface Device—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
Product
Duplexers
-
Prices include interconnect cables and mounting rails or panels. Specify N or UHF connectors, or 7-16 DIN (extra cost). All duplexers are factory turned. Specify pass and reject frequencies. 30-50 MHz duplexers have a tuning range of approximately +/- 2.5 MHz from center frequency as built.
-
Product
JTAG/Boundary-scan Digital I/O Module
ScanIO-300LV
Digital I/O Module
The ScanIO-300LV JTAG/boundary-scan digital I/O module turns an IEEE-1149.1 boundary-scan controller (such as the Corelis PCI-1149.1/Turbo or NetUSB-1149.1) into a powerful digital interconnect and functional tester.
-
Product
6-Port PCI Express
PEX 8724
-
The ExpressLane™ PEX 8724 is a 24-lane, 6-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8724 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785324-01
Interface
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Modules
-
VPC offers a wide array of modules with a variety of connection options that are configurable for virtually any interconnect requirement.
-
Product
Test Point Terminals
-
Zierick Manufacturing Corporation
Zierick PCB test point terminals offer exceptional designed-in flexibility, allowing test engineers to easily attach J hooks, EZ hooks, lead grabbers, clips and other test probes.All Zierick test point terminals are available with stress-free Accu-Lok mounting for a reliable PCB interconnection.
-
Product
Coaxial Adapter, 3.5 mm (m) to 3.5 mm (f), DC to 26.5 GHz
83059C
Contact Adapter (Receiver)
The Keysight 83059C instrument-grade 3.5-mm coaxial adapter offers outstanding performance to 26.5 GHz. With SWR typically better than 1.05, this adapter is ideal for most connector saver and interconnect needs.
-
Product
Universal Test Socket Receptacle
Series 6556
-
Universal Test Socket Receptacle. The Aries Universal Test Socket Receptacle is sturdy, open frame, and easily mounted to PC boards. Allows for easy replacement of Aries and other manufacturers test sockets. A choice of four collet pin styles makes the receptacle useful for any interconnection method.
-
Product
Multipin Industrial Connectors
-
Radiall VanSystem designs and produces circular electrical connectors for professional applications and harsh environments to support a wide range of fields including: railways (in rolling-stock as well as signaling applications), machine tools, automation, construction sites, research, power supply, extractive industries, plant engineering. In addition to connectors with screw or bayonet coupling complying with the MIL-DTL-5015 standard, Radiall VanSystem designs and manufactures non-standard interconnection solutions for special applications.
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 450 x 330 mm (wxd)
CMCSK-07-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Signal & Power PCB Connector
HPW Series
-
Smiths Interconnect's HPW series is a versatile interconnect with mixed signal and power contacts, up to 15A each
-
Product
9050 - 50 Module, 2-Tier Solution
-
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
