Interconnects
Links between systems, networks,nodes, equipment, devices, components and circuits.
See Also: Mass Interconnect, Connectors, Cable Assemblies, Interfaces
-
Product
eDAK For MAC Panel
JT 2147/eDAC for MAC Panel
-
The JT 2147/eDAK is a new variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within a MAC Panel ‘Scout’ mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry plus four independent, programmable TAP modules (two of type JT 2149 and two of type JT2149/MPV) on a single board that matches the MAC Panel Direct Access Kit (DAK) form factor. Overall this configuration offers four Test Access Ports, 64 Digital IO Scan channels and reconfigurable (SCIL) capabilities
-
Product
Calibration & Demag.
Model 990A/990C
-
The Model 990 Series Magnetreaters® are highly accurate, pulse type, ringing demagnetizers (also called treaters) for the controlled stabilization of permanent magnets and permanent magnet assemblies. Regardless of line voltage stability, they provide a controlled output through continuous pulse amplitude regulation. Treating voltage is variable from 0 to 600 VDC. Additional energy can be added to the Model 990 Series by interconnecting a Model 992 Energy Booster. The energy level is increased from 18 to 36 watt-seconds. With this option, treating coils will produce higher demagnetizing fields and lower ringing frequencies, which can provide greater field penetration in some applications.
-
Product
MIL-STD-1553
-
CAES SµMMIT™ Interconnect Products provide an intelligent solution to address MIL-STD-1553 multiplexed serial data bus challenges in avionics and spacecraft onboard data handling subsystems for both military and civil applications.
-
Product
PAM analysis upgrade for Signal Integrity Studio, WavePulser 40iX High-Speed Interconnect Analyzer
WAVEPULSER-SI-STUDIO-UPG-PAM
Analyzer
Signal Integrity (SI) Studio uses SDA Expert (SDAX) serial data analysis software options to simplify NRZ or PAM serial data jitter, eye diagram, noise and crosstalk measurement and analysis setup.
-
Product
Cost-Effective ATE System
PRO RACK ATE
-
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
Product
Powered VXS Crates
-
VXS - "VME-bus switched serial" is the new ANSI / VITA 41 standard which combines the 32-bit parallel VME-bus with high speed switched serial interconnect fabrics in order to increase the data transfer bandwidth to several GB/s.
-
Product
Signal Conditioners
-
Omega's modular signal conditioners provide a low-cost, high-performance method of inter-connecting real-world analog signals with data acquisition, monitoring, or control systems.
-
Product
Vacuum 90 Series Modules
-
VPC offers a wide array of modules with a variety of connection options that are configurable for virtually any interconnect requirement.
-
Product
Heavy Duty Modular Connector
HyperMod Series
-
Smiths Interconnects’ heavy duty, modular, rectangular HyperMod Series is available with a variety of contacts, special shells for harsh environments and special high creepage/clearance modules. The series conforms to DIN 43652 standards and is NF F61-030 railways approved.
-
Product
PCB Connectors
HPH Series
-
Smiths Interconnect's HPH series is a high density interconnect available up to 303 contacts with multiple hardware choices and backpotting option
-
Product
NVM Express
-
NVM Express is a scalable host controller interface designed to address the needs of Enterprise, Data Center and Client systems for supporting chip-to-chip, board-to-board, adapter and distance solutions. The protocol can efficiently use interconnect and fabric technologies such as PCI Express, Ethernet and Fibre Channel. Teledyne LeCroy provides protocol analysis, emulation, exerciser and other test equipment to service all NVMe storage applications.
-
Product
PC104 Switches
-
Curtiss-Wright Defense Solutions
Our PC104 switches provide systems integrators with a fast and powerful way to interconnect chassis, cards, and CPUs through switched Fast and Gigabit Ethernet links. These PC/104 Ethernet switches, optimized for size, weight, and power (SWaP)-sensitive embedded military and civilian computer network systems applications, enable reliable local area network (LAN) switching in extended operating temperature ranges and extreme shock/vibration environments.
-
Product
CompactPCI Instruments
-
Is a computer bus interconnect for industrial computers,combining a Eurocard-type connector and PCI signaling and protocols. Boards are standardized to 3U or 6U sizes, and are typically interconnected via a passive backplane. The connector pin assignments are standardized by the PICMG US and PICMG Europe organizations. The connectors and the electrical rules allow for eight boards in a PCI segment. Multiple bus segments are allowed with bridges.
-
-
Product
Attenuator Interconnect Kit, 2.92 mm
11716D
Interconnect Adapter
The 11716D attenuator interconnection kit provides the necessary parts to connect 84904L and 84906L programmable step attenuators in series.
-
Product
Three Phase Tester
4200
-
Peaceful Thriving Enterprise Co Ltd
*Fast and accurate measurement.*Portable and compact design, easy to carry.*Efficient, effective, reliable, easy and safe to use.*Two function in one unit. Including open phase and phase sequence.*This is idea for installing conveyor lines, pump systems and interconnected drivers.*Indicate phase orientation (clockwise or counter-clockwise) and whether each of three phases is live.
-
Product
PXI 32 x SPDT Reed Relay
40-110-121
Relay
Our 40-110 and 40-115 range of reed relay switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120/125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
Product
VME & Mezzanine Switches & Routers
-
Curtiss-Wright Defense Solutions
Our VME and mezzanine switches and routers provide systems integrators with a fast and powerful way to interconnect chassis, cards, and processors through switched Gigabit Ethernet links. Operating at wire-speed, these networking modules can be used to architect a network-centric infrastructure for advanced military systems.
-
Product
BGA Socket And BGA Adapter Systems
-
Mill-Max's BGA Socket/Adapter Systems are used for both socketing BGA devices and interconnecting circuit boards. Systems are available to fit 1mm, .050" and .8mm grid footprints.
-
Product
PXI 5A Fault Insertion Switch 10-Channel
40-196-001
Fault Insertion Unit
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
Product
Environmentally-sealed plastic connector
REP Series
-
Smiths Interconnect’s REP series is easy to use for quick mating. The REP panel and cable connectors are a highly cost-effective interconnect system, which solves the constant need for simple and reliable connector solutions in rail applications.
-
Product
USB Extender via CAT5 to 200 Feet
USB-C5-200
-
The USB-C5-200 extends up to four self-powered or bus-powered USB devices to 200 feet. The USB extenders consist of two units, the local unit and the remote unit, which are interconnected with CAT5/5e/6/7 cable.
-
Product
Keysight 20-Channel 5A Form A Switch for 34980A
34938A
General Purpose Switch
The Keysight 34938A is a high power general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 20 independent single-pole, single-throw (SPST) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Its 30VDC/250VAC, 5A contacts can handle up to 150W on a single channel, enough for many power line switching applications. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
Product
Boundry Scan Testers
-
Qmax Test Technologies Pvt. Ltd.
Boundary Scan Trainer Kit was developed by Qmax to provide user a good understanding and hands on the testing principals of boundary scan namely the scan chain test, interconnect test, non-BS functional testing of logic IC and cluster like a combinational or sequential circuits.
-
Product
Cables and Accessories
-
In addition to offering standard mating cables and connectors for AIM products, we also can provide cables and accessories to solve your avionics bus interconnect requirements.
-
Product
9025 Rack Mount
-
VPC rack mountable receivers like the 9025 meet the standards which are essential to support advanced mass interconnect requirements. Connector modules can be intermixed to establish custom interfaces which are ideal for functional and system testing applications.
-
Product
Silver Button Sockets
-
For BGA, QFN, or LGA applications, GTP contact technology provides >94 GHz signal speed and can additionally be used in high cycle life applications such as ATE. These sockets support pitches from 0.2 mm to 1.27 mm. Ironwood's GT sockets are ideal for prototyping and testing almost any BGA device application. These IC sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss (1dB at 94GHz) and supports BGA packages with pitches down to 0.2mm was utilized in these sockets. GT BGA sockets are mechanically mounted over a target system's BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry's smallest footprint).
-
Product
Terminals And Test Points
-
Today's high tech electronics require space saving, low cost methods for connecting and testing circuitry. Our complete line of Quick Fit terminals, Screw Terminals, Solder Lugs and Test Points and Jumpers are designed to meet the interconnect and testing challenges for electronic and electrical component termination points.
-
Product
Standalone Test System
1000 Series ATE
-
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
Product
Digital IO
PA32IX
Digital I/O
The PA32IX represents a new level of performance and capabilities for PXI-based digital instrumentation. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 512 bi-directional pins (16 boards). The PA32IX also supports deep pattern memory by offering 64 M of on-board vector memory with static per pin direction control and with test rates up to 50 MHz.
