Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
Product
Hall Effect Proximity Switches/Sensors
-
ChenYang Technologies GmbH & Co. KG
A Hall Effect proximity switch is a non-contact electronic switch, which consist of a permanent magnet or ferromagnetic part as trigger intermediary and a Hall Effect sensor IC. The Hall sensor IC detects the change of the magnet field when the permanent magnet comes in the close proximity to it and generates an electric signal. This signal is amplified and rectified to control the output signal of the switch.
-
Product
Long Wave Infrared Cameras
Calibir DXM640 Series
-
The Calibir uncooled Long Wave Infrared camera platform offers outstanding shutterless imaging performance and is optimized for Size, Weight and Power (SWAP). The Calibir DXM640 series features both shutter and shutterless operation and rapid image output on power up while delivering uniform response over the entire operating temperature range, making it ideal for thermal imaging applications requiring uninterrupted image acquisition. ULIS’s gen2 sensor offers an improved NETD and the updated calibration include customized gain correction on a per lens basis to offer even better image performances and response uniformity.
-
Product
5 Mega Pixel Custom Lens Camera Module
e-CAM51_CU5640_MOD -
-
The e-CAM51_CU5640_MOD is a small form-factor pluggable 5 Mega pixel custom lens camera module. Moreover, a wide variety of interchangeable lenses can be used on this custom camera module. It is based on OV5640 CMOS Image sensor from Omnivision Inc. The e-CAM51_CU5640_MOD is designed to connect with any application processor that has Parallel/MIPI digital video interface.
-
Product
Field-installation Type Electric Conductivity Meter (Four-Wire Transmission, For High-concentration)
HE-200H
-
HE-200H connects conductivity sensor (FES-125F,126F) and measures conductivity and temperature in the sample water. It can be used not only for measurement of electrical conductivity in aqueous solution, but also for concentration adjustment and rinse monitoring of CIP, etc., as well as for concentration monitor of process.
-
Product
Clamp Meters
-
TES Electrical Electronic Corp.
Variable Frequency drive measurement. LoZ voltage measurement to drain ghost voltages. Check 3phase sequence. True RMS reading on AC and DC+AC mode. Inrush current measurement. A measurement for HAVAC flam sensors.
-
Product
Optical Sensors
-
Many measurements are much easier to make with light. Southern Photonics designs and manufactures optical sensor systems for a wide range of applications including gas sensing and strain sensing.
-
Product
Innovative Software Tool Solutions
-
IoT brings networking to a wide range of potential "things" ranging from everyday devices to sensors and actuators. Telchemy's management architecture is uniquely designed to handle massive numbers of devices, providing data correlation, reporting and action triggers.
-
Product
Quantum & Metrology Instruments
-
Beyond quantum sensors, Exail’s photonics solutions enable real applications in other quantum technology fields. They also enable precise control and transmission of the frequency, phase and amplitude of a laser light through fibered telecommunication links, for metrology applications. The true and deep understanding of Exail teams for the fundamental physics behind its technology explains the absolute quality of its time & frequency reference products.
-
Product
3.4 MP Google Coral Camera
E-CAM30_CUCRL
-
e-CAM30_CUCRL is a 3.4 MP 4 lane MIPI CSI-2 custom lens camera board for Google Coral development board. This Google coral camera is based on 1/3" inch AR0330 CMOS Image sensor from ON Semiconductor® with 2.2 µm pixel.
-
Product
Calibration Equipment
-
Calibration is the method of comparing tools and measuring devices to higher accuracy standards. Torque calibration equipment is the official means by which torque testers and sensors are calibrated and are traceable to National or International Standards, such as N.I.S.T and ISO. In order to maintain precision accuracy, it is essential that torque measuring equipment be calibrated regularly. By equipping your team with Mountz calibration equipment, you can avoid the costly chore of sending your torque tools to the lab whenever they fall out of alignment.
-
Product
16-Channel Bridge Signal Conditioning Unit
ProDAQ 5716
-
The ProDAQ 5716 is a 1U high rack-mountable signal conditioning box for standard 19 in. racks. It provides signal conditioning for up to 16 strain gage or ICP sensors. Either one ProDAQ 3416 16-Channel ADC Function Card or up to two ProDAQ 3424 8-Channel 24-bit Sigma-Delta ADC Function Cards can be connected to the unit.
-
Product
Infrared Radiometers
-
Calibrated to a custom black-body cone with a measurement uncertainty of 0.2 C from -30 to 65 C when the sensor (detector) temperature is within 20 C of the surface (target) being measured. Radiometers are only sensitive from 8 to 14 m (atmospheric window) to minimize the influence of water vapor and CO2 on the measurement.
-
Product
Fall Detection Switches
-
Panasonic Industrial Devices Sales Company of America
Compact tip sensor with reliable photo sensor design. Applications include: Gas Heaters, Electric Fans.
-
Product
Machine Vision Camera - 1.6 MP, 78 FPS, Sony IMX273, Color
Blackfly S Board Level
-
The FLIR Blackfly Board Level variants are high performance, machine vision, area scan cameras designed for embedding into tight spaces. Unlike many board level cameras, it boasts a rich feature set applied to the latest CMOS sensors; the same feature set as the cased version. It is ready for integration with proven compatibility with popular SBCs and SOMs. The Blackfly S board level models enable OEMs to develop smaller, lighter, and lower cost solutions with embedded system connectivity and rich features.
-
Product
Glare Sensors
-
The Glare sensor detects and distinguishes glare on even surfaces. It also provides maximum reliability and saves costs. Previously, gloss on object surfaces was a disruptive factor that regularly had engineers breaking into a sweat.Now, gloss properties are a distinguishing criterion for process control – regardless of color, transparency or pattern. And it will be engineers’ eyes that shine, not their brows. Equipped with intelligent Delta-S-Technology, Glare is a further milestone in customer-oriented sensor development. Once again, SICK is confirming its leading position in opto-electronic sensors for the detection of a range of objects.
-
Product
Measurement, Communications & Testing
-
Process & Analytical Instruments division of AMETEK
Measurement Communications & Testing provides the design, integration and installation of critical communication systems, workflow, life-safety solutions and calibration instruments for temperature, pressure and process control. It also is a leader in level measurement devices, continuous position sensors, hardness testers, force measurement devices and retractable cord reels. In addition, it offers a line of weathering test instrumentation along with laboratory and outdoor testing services.
-
Product
PXIe-7821, Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module
783485-01
Digital I/O Module
Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7821 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7821 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in-‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
Speed Switches & Sensors
-
Monitor Speed and Detect Motion of Conveyors and Other Rotating Apparatus for Premium Protection of Expensive Belting and Equipment
-
Product
Fiber Photodiode Power Sensors
-
These interfaces provide communication between an attached sensor and a PC or other external control unit. They are designed to be controlled via an external device or operated autonomously using the analog output; there are no controls or display screens.
-
Product
1/2.5" 5.0 MP Low Noise USB Camera (Color)
See3CAM_CU55
-
See3CAM_CU55 is a 5.0MP USB3.1 Gen1 UVC Color Camera with S-mount (also known as M12 board lens) lens holder. It is a two-board solution containing camera sensor board based on 1/2.5" AR0521 image sensor from ON Semiconductor and USB3.1 Gen 1 Interface board. The powerful on-board Image Signal Processor (ISP) brings out the best image quality of this 2.2micron pixel 5MP AR0521 CMOS image sensor making it ideal for next generation of high resolution surveillance, biomedical instruments and biometric authentication applications.
-
Product
General Purpose Dual Flange Reaction Torque Sensor
TRS SERIES
-
The TRS Series reaction torque sensors offer long term reliability due to non moving parts and state of the art bonded foil strain gages. The anodized aluminum TRS Series is also available as a two axis sensor, torque and thrust, on special request. Whenever possible, the best approach for precision torque measurements is via reaction torque sensing, eliminating high maintenance and high cost of slip rings, bearings, and brushes.
-
Product
Water Activity Meter
LD-LWTM-A10
-
Water Activity MeterLD-LWTM-A10is a real portable water activity meter, with a weight of only 1.5 kg, lighter than a mobile phone. It has 0 to 1.0 aw range and offers operating temperature range from 0 to 50˚C. Designed with 6 bit backlight LCD digital display and integrated nonconductive humidity sensor. It measures fast activity of water within 5 minutes and under-voltage alarm indication function. It is easy to measure water activity anytime and anywhere also used in free water in the state of food balance.
-
Product
Transportation Data Logger MSR175
MSR175
-
Transportation data logger MSR175 for shocks, jolts, temperature. The MSR175 stand-alone data logger uses high-resolution sensors to continuously record what happens to your goods during transportation. The logger data can then be analysed very accurately – be it in order to ascertain damage or to improve transport packaging – using the “MSR ShockViewer” software.
-
Product
PC Vibration Measuring System VibroMetra
-
Metra Meß- und Frequenztechnik Radebeul GmbH & Co. KG
*The system was designed for typical tasks of vibration measurement. No ballast by unwanted functionality. *The system is modular making it upgradeable and particularly economic with fewer channels.*The necessary hardware is very compact which makes it particularly suited for mobile use.*Short installation and training time. After a few minutes you may start with the first measurement.*Off-line measurement: VibroMetra permanently saves the raw data stream of the sensor signal in the background. By this means you may analyze your measurement later again with other settings or other software instruments.*Data export as graphics, text or binary file
-
Product
NI-9230, 3-Channel, 12.8 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module
784396-01
Sound and Vibration
3-Channel, 12.8 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module - The NI‑9230 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9230 is also compatible with smart TEDS sensors. The NI‑9230 incorporates software-selectable AC/DC coupling, IEPE open/short detection, and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
Arduino CAN Shield
IFB-10003-ANP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Web Sensor with PoE
T7611-2
-
Ambient temperature, relative humidity, atmospheric pressure t-line Web sensor with Power over Ethernet feature. Remote alarm.
-
Product
RTD Data Logger
-
RTD Data Logger is the most commonly used sensors for measuring temperatures in various industries. These are positive temperature coefficient resistive sensors and Pt100 is the most commonly used type of RTD sensor which has 100 ohm resistance at 0 C. IM2000 series RTD data loggers offer bridge measurement technique to compensate for effect of wire length. In addition logger has facility to program offset so that the measurements are more accurate.
-
Product
Proximity Sensors
-
Inductive proximity sensors are the preferred choice for the majority of applications requiring accurate, non-contact detection of metallic objects in machinery or automation equipment. As a pioneer and market leader, Pepperl+Fuchs offers innovative, high quality inductive sensors to meet the needs of the worldwide automation and process control markets. Our experience, flexibility and customer focus continues to allow us to offer custom designed solutions for the most unique and demanding applications.
-
Product
Dynatrol® Level Switch for Light Bulk Solids
CL-10GJ
-
Dynatrol® CL-10GJ Level Sensor is designed for sensitive or problem applications of materials that have a tendency to bridge or pack. It handles difficult products such as flour, cocoa, sugar, pharmaceutical powders, powdered lime and additional bulk solid materials for high, intermediate or low-point level detection. The CL-10GJ is typically used with bulk solid materials in the density range of 10-15 lbs/ft3.
