Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
product
SparkFun Qwiic Micro:bit Breakout
The SparkFun Qwiic micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:bit to breadboards and other Qwiic sensors, motors, LEDs and more.
-
product
Dielectric/Conductivity Sensor
Micro-VariconTM
The Micro-Varicon sensor is a miniature, thin, flexible dielectric sensor designedfor cost-sensitive use where space is limited. The electrode array is patterned on apolyimide substrate, and the Micro-Varicon sensor can be supplied with or withoutTeflon insulated leads.
-
product
PCI Precision Resistor Card 4-Channel
50-297-130
The 50-297 PCI precision resistor provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 range is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
AC Current Sensor
RCTi and RCTi 3ph
The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.
-
product
GPS Jamming and Spoofing Detection Sensor
BroadSense
BroadSense is a GPS jamming and spoofing detection sensor designed to provide real-time and historical situational awareness data. Utilizing sophisticated GNSS receivers and patented jamming and spoofing detection algorithms, BroadSense can detect when the GPS signal or GPS spectrum is compromised.
-
product
High Performance Machine Vision Cameras
Goldeye
High-performance machine vision cameras with advanced features for demanding applications. QVGA and VGA Resolution. InGaAs sensors. Up to 344 fps. Spectral range 900 - 1700 nm (SWIR).
-
product
Field-installation Type Residual Chlorine Meter (Four-Wire Transmission, Water flow beads)
HR-200
HR-200 is connected to a residual chlorine sensor (RA-20), which allows the free residual chlorine concentration to be measured with high accuracy. It is sutable for waterworks, pool water sterilization, and desalination systems. The measurement method is a three-pole polarographic method, which enables continuous monitoring of residual chlorine concentrations without using reagents. Stable measurement over a long period was realized by physical polishing cleaning using beads.
-
product
32-CH 12-Bit 100 kS/s Isolated Analog Input Card
PCI-9113A
ADLINK PCI-9113A is a 32-CH, 12-bit, 100 kS/s isolated analog input card. The PCI-9113A provides analog inputs with 3 programmable input ranges for both bipolar and unipolar inputs. The 32-CH single-ended analog inputs can be converted to 16-CH differential analog inputs, which improve the noise rejection in harsh industrial environments. The analog inputs are isolated from the PC's system ground. This feature not only protects the PC from being damaged from surges on the signal lines, but also eliminates ground loops and common-mode problems commonly seen in industrial measurement applications. The PCI-9113A provides custom circuit area for input signal conditioning. Either signal attenuation or filtering can be applied on per channel basis. With all the features, ADLINK PCI-9113A delivers cost-effective and reliable data acquisition capabilities for ATE, sensor monitoring, data logging, power transmission, and a broad variety of industrial measurement applications.
-
product
Imaging Colorimeter
FW-Series
RayClouds Photoelectric Technology Co.,Ltd.
FW-Series Imaging Colorimeter is equipped with scientific grade CCD sensor and multi-filter, cooperated with ProICM professional analysis software to detect and analyze the optical characteristics of two-dimensional imaging screen. Improving measurement efficiency to ensure manufacturers maximize the production of high visual quality products.
-
product
Process instrumentation
Temperature measurement
Our product range includes both electronic and mechanical temperature measuring equipment and is constructed in a flexible modular way.The CombiTemp System includes a series of basic elements which can be combined as various temperature sensors and temperature measurement transmitters. The system also includes a wide array of connectors for standard processes and where hygiene rules apply.
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 11.4MΩ
50-297-153
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Pitot Tubes
The dpm-i Pitot Tube is a new design concept in Pitot Static Tube technology. It is a multi-functional sensor. It can replace thermally heated instruments, where power requirements are high. Gives easy access to duct measurement compared to a standard Pitot Tube. For example, in ceilings voids and confined areas, where there is a thick lagging or metal cladding.
-
product
Suitable For RTD Sensors Approved To ATEX And IECEx Standards
TTR200X -
The TTR200X is our mid range transmitter for RTD or Slidewire sensors approved to ATEX and IECEx standards. It can accept many different types of RTD sensor such as Pt100, 500, 1000 etc and slidewire sensors up to 100K Ohm
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-200B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Digital Pressure Gages
General purpose digital pressure gauge provides exceptional performance, stability and reliability. The laser welded stainless steel sensor and socket make this product suitable for use with a wide variety of pressure media in demanding industrial applications. The DG25 was designed with OEM in mind and can easily be custom configured to meet unique requirements.
-
product
Displays & Signal Processing
Sensors in manufacturing and process technology deliver a wide variety of digital and analog signals . In the case of decentralized counting and control processes, these signals often have to be clearly displayed, monitored or further processed. So that you can optimally solve these tasks within your system, we offer a wide range of counters, process displays, signal converters and other downstream devices , which are optimally matched to use with our sensors.
-
product
Fault Detection and Classification (FDC)
E3™
Fault detection and classification (FDC) transforms sensor data into summary statistics and models that can be analyzed against user defined limits to identify process excursions. For process and equipment engineers, maximizing equipment effectiveness, reducing yield excursions, improving product cycle time and enhancing the overall output of the factory are key success metrics. SmartFactory FDC is built on Applied's equipment control technology, the E3 platform, which promotes information sharing.
-
product
PXIe-4499, 204.8 kS/s, 114 dB, 4 Gains, AC/DC-Coupled, 16-Input PXI Sound and Vibration Module
781370-01
204.8 kS/s, 114 dB, 4 Gains, AC/DC-Coupled, 16-Input PXI Sound and Vibration Module - The PXIe‑4499 is designed for high‑channel‑count sound and vibration applications. With 24-bit analog inputs and IEPE constant current signal conditioning, the PXIe‑4499 is ideal for making precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. The PXIe‑4499 delivers simultaneous sample on all channels. In addition, the PXIe‑4499 includes built-in antialiasing filters that automatically adjust to your sample rate, software-selectable input gains, and TEDS smart sensor support for error-free setup. Common applications include noise, vibration, and harshness (NVH) analysis; large microphone arrays; and dynamic structural test.
-
product
Soil Moisture Loger Sensor
NUL-229
This logger sensor is based on measuring the partial vacuum pressure in a tensiometer. A tensiometer is a closed tube with a special ceramic part in its end. The tensiometer is filled with water and put in the soil. If the soil is dry, water goes out by diffusion through the ceramic holes and partial vacuum pressure is created in the tensiometer. When we wet the soil, the partial vacuum in the tensiometer pulls water into the tensiometer and the vacuum decreases. This is why soil moisture is measured in pressure level.
-
product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-04
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Exhaust Gas and Wheel Space Thermocouple
EGT
AMETEK Exhaust Gas (EGT) and Wheel Space Frame Turbine Thermocouples meet the specific operational and performance requirements for REPLACEMENT and RETROFIT Frame gas turbine applications. AMETEK's expertise in solving creep, stress, rupture, corrosion, EMF drift, and other problems affecting sensor performance has resulted in a robust line of single and dual element thermocouple designs. Typical applications include wheel space and exhaust gas temperature monitoring.
-
product
Environmental Chamber
REXMED REC-400
MOD. REC-400, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,506 Watts, 11,962 BTU/hr, 3,020 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Sensors
3D Fiber Probe
Ultra high precision 3D measurements2D image processing combined with a laser distance sensorSelf illumination modeLowest contact force of 1 µNProbe sphere diameters from 0.040 mm to 0.250 mmControl and evaluation software for fully automatic measurements
-
product
PXI High Density Precision Resistor Module, 18-Channel, 2Ω to 31.5Ω
40-298-010
The 40-298-010 is a high density programmable resistor module with 18 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Situational Understanding Mission Intelligent Technology
SUMIT360™
The SUMIT360™ provides military armored vehicle operators with an innovative, 360 degree view of the environment around the vehicle utilizing advanced sensor technology to improve threat and obstacle detection that could pose a threat to ground forces, and their mission. Equipped with powerful multi-spectral sensors in each module, the system uses on-board processing to form seamless, stitched images to provide a full field of view in any terrain, and virtually any conditions, day or night. With additional target detection and identification capability, the system can also be paired with advanced analytics and Artificial Intelligence (AI) to provide vehicle crew, and transported troops a threat detection and classification to provide critical decision support before opening the hatch. The system also provides the ability to support remote or optionally manned configurations.
-
product
Network Attached Storage / Fibre Channel
CNS4-FC
Curtiss-Wright Defense Solutions
The Compact Network Storage 4-Slot - Fibre Channel (CNS4-FC) is the perfect storage solution for programs looking to modernize systems using legacy Fibre Channel (FC) or Serial-Attached SCSI (SAS) drives. Providing many of the benefits provided by the CNS4, the CNS4-FC brings newly added support for FC protocol plus other network protocols like Network File Server (NFS), Common Internet File System (CIFS), File Transfer Protocol (FTP), Hypertext Transfer Protocol (HTTP), and Internet Small Computer System Interface (iSCSI) making it ideal for sharing critical data in a deployed network for mission platforms that were developed with sensors utilizing FC as the protocol.
-
product
Mutlifunction Stud Sensor
A tool that detects multiple items behind walls, including wood studs, metal, and live AC electrical wires.
-
product
Pressure Sensor Interface
USB2251
The USB2251 Pressure Sensor Interface provides real-world data acquisition for your PC via the USB port. 8 calibrated variable reluctance pressure sensor inputs are accepted by the USB2251. No external signal conditioning is required.The USB2251 includes a connector panel for sensor cables, calibration constants for each sensor , configuration and data acquisition software. The USB2251 produces a floating-point value for all readings, directly in engineering units.The USB2251 can record pressure readings up to 5000 samples per second. Combined with the fast response of the Validyne VR pressure sensors, the USB2251 is ideal for transient pressure studies. The USB2251 is compatible with the following Validyne variable reluctance pressure sensors: AP10, DP103, DP10, DP45, DP15 DP360, DP215, and DP363. Each sensor is calibrated with the USB2251 at the factory and is ready to make measurements.
-
product
Non-Contact Chemical Concentration Monitor
CS-900
In order to fulfil the tight chemical concentration control required in semiconductor WET process, HORIBA realizes higher functionality to meet the needs by designing compact equipment while maintaining stable measurement and carrying out operator safety through its original sensor design.
-
product
DC/10 MHz 50 GHz USB Thermocouple Power Sensor
U8487A
The U8480 series is Keysight's first power sensor with the capability to measure down to DC (only applicable for U8481A/85A). Now, with an expanded frequency range up to 50 and 67 GHz, the U8480 series allows you to make fast and accurate high frequency power measurements in applications ranging from PNA/MXG calibration to high volume manufacturing.
