-
product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784776-01
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
product
LXI WTB Terminator, 90.6 ohm
60-983-002
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
PXI-5652, 6.6 GHz RF Analog Signal Generator
779670-02
6.6 GHz PXI RF Analog Signal Generator—The PXI‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Dual Polarized Antennas
Dual polarized horn antennas are offered as both standard and custom models with rectangular waveguide interfaces for both horizontal and vertical ports. These dual polarized horn antennas support both linear and elliptical polarized waveforms. When the antenna receives a circular polarized waveform, equal amplitude linear polarized waveforms are output at both horizontal and vertical ports. When two equal amplitude linear polarized waveforms are input into the vertical and horizontal ports, the antenna will transmit a circular polarized waveform. The listed models offer 15 dB nominal gain and 33/28 degrees typical half power beamwidth at the center frequency of the band. They also exhibit 40 dB typical port isolation and 35 dB nominal cross polarization. These antennas cover full waveguide bandwidths within the frequency range of 8.2 to 110 GHz. In addition to the models listed below, models with 10, 20, 23 and 25 dB gain and other frequency bands are also available.
-
product
16 Bit DDS Generator Up To 200 MHz
96xx series
The 96xx series DDS generators deliver the highest performance in both speed and resolution. The series includes produts between one and 24 synchronous channels. DDS – Direct Digital Synthesis – is a method for generating sine waves from a single, fixed-frequency reference clock and is widely used in signal generation applications. The DDS functionality implemented on Spectrum Instrumentation’s AWG platform is based on the principle of adding multiple “DDS cores” to generate a mul?ti-carrier (multi-tone) signal, with each carrier having its own well-defined frequency, amplitude and phase. In addition to these static parameters, there are also build in dynamic parameters like frequency slope and amplitude slope to allow for intrinsic linear changes for multiple cores.
-
product
Measurement
AC Voltmeter
AC Voltmeter is used for measuring AC voltage. The software is capable of switching measurement modes (RMS or amplitude), but regardless of the selected mode the information about the current peak value is always displayed.
-
product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Single Axis AC Magnetic Field Sensor
MGC-1A
Macintyre Electronic Design Associa
The MGC-1A is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1A amplitude response is insensitive to the frequency of the field over its 30 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
product
Broadband Amplifiers
R&S broadband amplifiers are innovative solid-state solutions with exceptional RF performance for generating RF power up to 13 kW in the frequency range of 4 kHz to 6 GHz. Designed as very compact amplifiers, at highest power density, they are robust against severest output mismatch while featuring high availability. Applications range from amplitude, frequency, phase, pulse to OFDM modulation.
-
product
Digital Phase Shifter
Analog Devices digital phase shifters change the phase of RF, microwave, or millimeter wave signals while providing no amplitude change. They are used in a variety of applications, including RF PA linearization/RF distortion, amplitude and phase modulation, variable attenuators, and fiber optics.
-
product
Time Code Reshaper/ Distributor
SR-28
The SR-28 can drive time code over long cables, making it ideal for synchronization during live shows and remote recording. The SR-28 time code distributor, with two inputs and eight outputs, reshapes time code while distributing it, eliminating amplitude distortions and level fluctuations. The level of each output is individually adjustable via front panel pots. The input is selected via a front panel switch. Also included are 2 power inputs and an automatic switch over in case of failure.
-
product
Voltage and Current Amplifier
CMS 356
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
product
DSP Upconverters
Renesas digital signal processing (DSP) upconverter products include a quad programmable upconverter (QPUC) which is a QASK/FM modulator/FDM upconverter designed for high dynamic range applications such as cellular basestations and a wideband programmable modulator (WPM) which is a quadrature amplitude modulator/upconverter designed for wideband digital modulation.
-
product
Intelligent Interface Card
IIB-1553-PCI-2C
The IIB-1553-PCI-2C provides an intelligent interface card for two serial, dual redundant MIL-STD-1553 data buses and the PCI bus. The card supports 1553A, 1553B, McAir and STANAG 3838 variants on a single card. The IIB-1553-PCI-2C provides concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Two independent variable amplitude dual redundant 1553 interfaces are provided, each with2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
General Purpose Pulse Generators
These easy-to-use models offer wide operating ranges (PRF, PW, amplitude, etc). Manually-controlled (switches and dials) and modern computer-controllable models (with GPIB, RS-232, and optionally Ethernet) are available.
-
product
Hardy Shaker
HI-913
This Hardy Shaker provides the ability to set the amplitude and change the frequency range without the amplitude changing. This automation makes conducting a test easier. A test can be conducted on a vibration transducer and manually recorded. Multiple tests are not saved; for multiple tests use the HI-903 or HI-803 units. The HI-913 is used for testing from 7 to 10,000 Hz, it offers adjustable frequency and vibration levels. This provides a reference source for verifying the accuracy of vibration transducers, connectors, cabling and instruments or instrumentation systems. The HI-913 has a ruggedized suspension system that can support heavy transducers (up to 800 grams - see frequency limits in the manual). The HI-913 has a built-in battery charger that can operate on 120 or 240 VAC. The unit comes in a rugged Pelican case.
-
product
Single Phase Relay Tester
PTE-50-CE Pro
This electronic, independent source can be adjusted in amplitude, frequency, and phase angle. It comes installed as standard with the ‘Pro’ versions of the PTE sets, but it can also be purchased separately and mounted by the user inside the unit’s lid in a few minutes.
-
product
Fixed Attenuators
DC to 220GHz
RF Attenuators are components that reduce the amplitude level of an incoming frequency signal. They are used to protect systems from receiving a signal with a power level that is too high to process. There are various types of fixed attenuators that can fit your engineering needs. Precision MMW will help you with the highest quality fixed attenuator products needs.View more Fixed Attenuators
-
product
Resonant Chopper Systems
Electro-Optical Products Corp.
An external clock signal, to provide an ultra stable modulating optical beam motion [sub] system. The system can be used as a "stand alone" unit, in the laboratory, or can be incorporated into a larger instrument/system. The chopper is ONE FIXED FREQUENCY, picked from the range of 5 Hz to 20 kHz. The chopper is a small size, light weigh, low cost and long life device. It requires low power drive electronics and does not radiate electromagnetic interference (EMI). It has high frequency stability and high amplitude stability. The chopper is IR, VIS and UV and high vacuum capable. Reference signal and position output available.
-
product
Radiation Portal Monitors
Baltic Scientific Instruments, Ltd
Radiation Portal Monitors (RPM) are fix-installed radiation detection systems designed for automated screening of pedestrians, vehicles and trains passing through the detection zone of RPM for presence of gamma and neutron radiation. The RPM alerts the security office and front line officer about the presence of radioactive and nuclear material and provides additional alarm associated information: type of alarm (gamma, neutron or both), relative amplitude of the alarm, etc.
-
product
Single Axis AC Magnetic Field Sensor
MGC-1
Macintyre Electronic Design Associa
The MGC-1 is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1 amplitude response is insensitive to the frequency of the field over its 5 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
product
Flammability Test System
COMP0804CAP
Active flammability test system according to IEC 60384-14 Ed4. For testing X & Ycapacitors up to 1uF. The test system includes control of the nominal AC supply via an integrated variac up to 1800V. Impulse amplitudes are programmable up to 8kV which covers all requirements. X1 capacitors are stressed up to 4kV, X2 and Y4 capacitors up to 2.5kV and Y2 capacitors up to 5kV.
-
product
Scalar Network Analyzer Extenders
A Scalar Network Analyzer is a type of RF network analyzer that is used to measure only the amplitude properties of a DUT (Device Under Test). Unlike a Vector network Analyzer, it does not measure both amplitude and phase of the DUT.
-
product
Real-Time Spectrum Analysis Software
S240
The ThinkRF S240 Real-Time Spectrum Analysis Software features a completely redesigned graphical user interface (GUI) from previous versions. Designed with the end-user in mind, the S240 keeps common setting such as Frequency, Bandwidth and Amplitude visible at all times, making it easy for the user to get the right view. All other settings and functions are available through an intuitive menu system that minimizes the number of clicks and the time it takes to find the right functions, while still keeping the view of the spectrum front and center. Customized settings can be saved and reloaded to simplify the setup of common applications and uses.
-
product
RF Ports Alignment Software
With the R&S®RF Ports Alignment software together with the option R&S®SMW-K545, Rohde & Schwarz provides a standard and tailored solution for calibrating amplitude, time and phase of multi-channel SMW setups. The RF Port Alignment automatically collects the gathered correction data for the multi-channel setup using a connected vector network analyzer such as the R&S®ZNA or R&S®ZNB. Thanks to an intuitive graphical user interface the test engineer is guided through the calibration procedure step-by-step in a convenient way. With a calibrated multi-channel setup, tests of advanced systems in wireless communication or of radar receivers can be performed straightforward.
-
product
RF Signal Generators
As Rigol's RF first signal source, the DSG3000 series offers standard AM/FM/ØM analog modulation, as well as options for I/Q modulation and I/Q baseband output. The instrument is available with maximum frequencies of either 3 GHz or 6 GHz. Featuring a high signal purity with phase noise measuring <-110dBc/Hz@20kHz (typical) and a wide output range of -130dBm to +13dBm, the DSG3000 RF signal generator has standard pulse modulation with an on/off ratio of up to 80dB, with optional pulse train generator available. The DSG3000 series also has an amplitude accuracy of <0.5dB (typical).
-
product
Axle Damping Test
MSD 3000 | VP 215033
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test stand MSD 3000 is characterized by a quick and precise physical check of the axle damping. The frequency-controlled plate excitation by means of electric motors determines the maximum oscillation amplitude and then evaluates the axle damping according to the principle of Lehr's damping. The fully automatic test sequence including the determination of the axle and vehicle weight enables a time-saving and reliable assessment of the axle damping.
-
product
Automatic Relay Test Set
MT2000 Series
Portable single phase dual current manual and automatic relay test set. Readymade test modules. Independent control of Phase angle, frequency and amplitude.
-
product
Spectrum Marker Generator
NSG-2
National RF, Inc. is pleased to announce the production of a new device, the Type NSG-2 Spectrum Marker Generator. The generator is intended to be used with either spectrum analyzers or communications receivers to mark specific frequency intervals in the RF spectrum. When used with receivers, it is essentially a frequency calibrator, thus making it attractive for use with vintage receivers with analog dials. The NSG-2 provides a leveled amplitude output over nearly 100 MHz of RF spectrum, thus making it ideal to mark frequencies and signal levels on spectrum analyzers. In addition, it may be used with a spectrum analyzer, in lieu of a sweeping type generator, to align lowpass, highpass, and bandpass filters with passbands greater than 20 KHz.
-
product
Ultra Low-Loss Cable Assemblies
dB Miser
Cost-Effective, High-Performance Solutions for Low Loss ChallengesConsider dB Miser™ ultra low loss cable assemblies. High performance materials, careful attention to design detail, and stringent process control yields:- Ultra low insertion loss over the specified frequency range- Excellent amplitude stability with flexure- Stable performance over operating temperature range - Increased shielding effectiveness - Greater connector retention
