Interface Adapters
Physical interface between interoperable elements.
See Also: Interfaces, Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Test Adapters
-
product
4x IDC to 192 Pin Quadrapaddle
YAV90Q04
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
product
Adapter, 1.0 mm (m) to 1.85 mm (f), DC to 67 GHz
11921G
The Keysight 11921G precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
product
850 Universal Interface
UI-5000
The most powerful educational lab interface in the world features numerous ports, a rapid sampling rate, and unmatched functionality.
-
product
Serial to Relay Interface Boards
Model 2364 OEM
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Serial interface header includes RS-232 and RS-485 signals. * GPIB interface header includes GPIB address switch input signals.* Includes 50-pin mating relay connector and serial header connector.* Optional 115750 Terminal Board for easy connections without soldering.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel.
-
product
PCIe Adapter for XMC
PCIe8LXMCX1
Simple and easy to use. Install PCIe8LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position.
-
product
ANSI X3.28 Interface Board
Model 4804B-7
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
product
Test Port Adapter Set, 3.5 Mm (Test Port) To Type-N
85130C
The Keysight 85130C test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 3.5 mm to type-N male adapter and a 3.5 mm to type-N female adapter. The frequency range for these adapters is dc to 18 GHz with a return loss of 28 dB or better.
-
product
Serial Protocol Host Adapter
SPI Storm
This is the primary step for using SPI Storm device. It consists in describing how you would like to access your serial device: whether you would like to write to your device, read from it or do both simultaneously
-
product
Hall Sensor Board with I2C Interface
046-322
Version: +5V/15A +12V/5A -5V/15A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
product
Mini Munitions Store Interface
MMSI
Mini Munitions Store Interface (MMSI) (EBR 1553) modules support up to 8 MMSI hub ports and composite Bus Monitor output using the M4KMMSI module. Each module can operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor, and Bus Monitor.
-
product
USB Controlled High Precision Audio Test Interface
AudioConnect 4×4
AudioConnect 4×4 is a high accuracy 4-in, 4-out audio interface specifically audio test and measurement. It offers digital and analog audio in and out at any user-specified sampling rate up to 200kHz, and a high signal to noise ratio and wide frequency response, making it suitable for the most demanding measurement applications. Controls are simple – a single USB connection and a power indicator – all other typical soundcard controls that are not used for audio test applications have been eliminated to make operation and calibration simple with no room for error. AudioConnect 4×4 is supplied fully calibrated.
-
product
EBIRST 200-pin LFH To 96-pin SCSI Adapter Cable
93-002-226
eBIRST adapters allow extension to other switching system connectors, including SMB
-
product
CPCI Or PXI Communication Interface Board
MS 1706
*Memory and IO Read Write Cycles*External Interrupts*32 bit Data Bus*30 bit Address Bus*Control Signals for external interface*Four RS232 PORTS with full handshake signals*Four RS232/RS422 PORTS without handshake signals*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
Wearable Wireless Adaptive Refractor
VisionFit SC
The VisionFit SC is an innovative, electronic, mobile and wearable adaptive refractor.It performs a subjective sight examination and effectively replaces both the trial frame and the manual/electronic phoropter functionalities. VisionFit SC enables examining in free posture. Subjective refraction can be performed with the patient in his/her usual working environment and posture.VisionFit SC does not require the control of the patient’s position making it ideal for non-cooperative patients. Thanks to its comfortable and small footprint, this device reduces the examination time and increases the peripheral vision.
-
product
16-Port RS232 Async Serial Communications Adapter PMC
2238
The Technobox 16-Port Async Communication adapter provides sixteen 16550-based UARTs using RS232 signaling levels.
-
product
10GBASE-T Ethernet PCI Express 2.1 x4 Single Port Adapter, AQC107
10 GigE Network Interface Cards
10GBASE-T Ethernet PCI Express 2.1 x4 Single Port Adapter, AQC107
-
product
Connector Interface, Connector Type FC - Narrow Key Way
81000NI
81000NI - FC/APC connector interface, good for >10000 reconnection cycles, 2.03mm (0.08") key way. (for R-keying only, narrow key way)
-
-
product
Coax, Contact, Receiver, 20/26 GHz, 3.5MM, w/ SMA Adapter, 90 Series Modules only
610102135
Primary mating contact 610102134. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – brassCenter conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination 3.5mm compatibleInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 26 GHzVSWR 1.15 + .01 (f) GHzInsertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mΩ max. center conductor3 mΩ max. shieldCable Specifications 3.5mm compatible Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MΩ min.
-
product
In-Line Coaxial-to-Waveguide Adapter, 1.0 Mm (m) To WR-12, 60 To 90 GHz
E281DS
E281DS In-line 1.0 mm (m) - to- WR-12 waveguide adapter offers a simple way of measuring waveguide devices in E-band, 60 GHz to 90 GHz.
-
product
ARINC 664 Part 7 XMC Interface Module
XMC-664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Radiometer Spectral sensitivities precisely adapted to the measurement task
UVS-B-T
Compared to the spectral response of the UVS-E, the UVS-B-T has a sharper cut-off at the transition from UV-B to UV-A. This feature reduces the UV-A contribution to the radiometer output and permits the highest possible correlation to atmospheric UV-B irradiance.
-
-
product
External DC Bias Adapter
16200B
The 16200B test fixture is designed to operate with high frequency LCR meters and impedance analyzers. It allows you to supply a bias current across the device of up to 5 Adc through a 7 mm port by using an external DC current source.
-
product
8 GHz Differential Probe with ProBus2 Interface
DH08-PB2
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Adapter, 2.4 mm (f) to 3.5 mm (m), DC to 26.5 GHz
11901D
The Keysight 11901D is a metrology grade, 2.4 mm female to 3.5 mm male adapter with dc to 26.5 GHz operation.
-
product
PMC-to-4X PCI Express (PCI-e/PCIe) Adapter
6777
The Technobox, Inc. P/N 6777 is a PCI Express (PCIe/PCI-e) carrier that permits the insertion of a single PMC into a PCI-e slot (4X). The adapter orients the PMC in a reverse manner such that the rear I/O from PN4 appears at the 68-pin SCSI-style connector installed on the adapter’s bracket. Furthermore, the reverse orientation of the card permits direct access to the standard front I/O (if any) within the host chassis.
-
product
3U CompactPCI 5-Port Serial Ethernet, Optional POE Card
cPCI-A3ETH
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP- 5x RJ-45 ports support up to 2.5G via Intel® i226IT Ethernet controllers- Optional PoE supported- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
product
Intelligent, Single- or Dual-Channel MIL-STD-1760 Adapter
EXC-1553UNET/Px-1760
The EXC-1553UNET/Px-1760 is an intelligent, single- or dual-channel, MIL-STD-1760 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1760 bus, both in the lab and in the field.The EXC-1553UNET/Px-1760 shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.In addition the EXC-1553UNET/Px(S)-1760 provides 8 I/O Discrete signals and an IRIG B input.
-
product
Rad-Hard Interfaces
Performance and flexibility are key words for ST's Interface ICs. Our latest generation of interface chipsets offer excellent immunity to radiation and high data rates while drawing very low consumption. Available with single-ended inputs/outputs (I/O) and also on differential tracks/cables with impedance matching, our space-qualified interface ICs accompany the decreasing voltage levels and the evolution toward serialization.
