-
Product
Fixturing
-
Terotest specialises in providing test solutions specific to customers' test applications. We understand that the interfacing and fixturing of a particular test setup can determine whether the application is a success or a failure, and therefore we strive to deliver solutions that are cost effective and suitable to user requirements.
-
Product
Test Fixturing Solutions
-
Amfax and MAC Panel have teamed up to provide a unique WIRE-FREE Test fixture technology. We have created an alternative solution to traditional wired ITAs called PECture(TM). The name is a combination of PEC (Printed Electronic Circuit) and fixture.
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
Test Fixture
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
SMD Array Type LCR Test Fixture
16034H
Test Fixture
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
Product
RF Functional Test Fixtures
-
EMC Technologies’ design team has developed a variety of test adaptors and test stations for testing RF circuit assemblies and microwave sub-assemblies.
-
Product
Latch-on Test Fixtures
-
Latch-on Test Fixtures provide a convenient way for production personnel to quickly and reliably make electrical connections to a product for programming or final test. These custom fixtures eliminate the need to hand-wire products in order to power them up and communicate with them. Typical applications for latch-on test fixtures are metering devices, control panels, and any type of controls that connect via terminal strips.
-
Product
ARINC HSI / ADI Test Fixture
TA-2000
-
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
-
Product
Flexible Probearm for HBM and Flex-Pitch Applications
TPA-GFG
-
High Power Pulse Instruments GmbH
*Electrically isolated probearm for GND needle contact or general purpose DC, twin-wire HBM or flexible pitch VF-TLP/TLP/HMM/HBM force/sense probing based on the HPPI GF-A flexible pitch setup.*Flexible rotation of the probearm by precision gear 80:1*Suitable to mount the GF-A ground fixture needle for flexible pitch measurements. In addition a cable (e.g. for HBM) can be directly connected to the contact pin.*High stability
-
Product
Test Fixture with API
TA-14VG
-
The TA-14VG test fixture is based on the requirements for the Integrated Test Procedure for the VG-14A assembly as shown in the OEM maintenance manual. The panel also contains a test point breakout for the units main connector as well as one for the VG-401 base. The VG-401 breakouts provide an in series connection that will allow easy access to the gyro's signals and also provides a way to monitor rotor current. The panel also contains a variac to allow for line voltage adjustment.
-
Product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
-
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
Product
Press - Down Fixture Kits
-
*Supports most press - down testers *High - Quality *Precise & Reliabe
-
Product
Software Module with a Virtual Gage for Real-Time Inspection and Assembly
Verisurf Build
-
Verisurf BUILD is the industry-leading tool for real-time model-based inspection, tool fabrication, and computer-aided assembly.Inspect position and profile, set details and fabricate tools, jigs, and fixtures faster and at lower cost than any other process or software.Evolved and perfected from a large installed base at today’s modern aerospace, automotive, and industrial tooling manufacturers.
-
Product
Wind Power Solution
NXA SIEMENS
-
The NXA SIEMENS is custom-made with firmware and fixtures designed specifically for Siemens 2.3, 2.4, 2.6, 3.6, and 4.0. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
High Speed Spin Fixture
1571P Series
-
The Model 1571 High Speed Rate Table System is designed to provide a precision high velocity testing solution for the development and/or production testing of inertial packages or their components.
-
Product
SHB12X-H3X24, Male InfiniBand to Differential Flying Leads, Shielded LVDS Cable, 1.5 m
196236-1R5
LVDS Cable
72-Pin, Female Flying Leads to 48-Pin, Male InfiniBand, 100 Ohm, Shielded LVDS Cable - The SHB12X-H3X24 LVDS Cable connects the 12X InfiniBand connector on PXIe-656x LVDS digital instruments or some NI 658x LVDS Adapter Modules for FlexRIO directly to individual header pins. This cable is intended for use with a custom breakout fixture. The flying-lead cable has three signals per grouping for positive, negative, and ground pin connections designed to plug directly into any 0.1 in. header connector. It is a shielded, 100 ohm cable.
-
Product
SHC68-H1X38 High-Speed Digital Flying-Leads Cable Accessory, 1.5m
192681-1R5
Digital Cable
76-Pin, Female Flying Leads to 68-Pin, Male VHDCI, Shielded, 50 Ω Digital Cable - The SHC68-H1X38 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments directly to individual header pins for use with a custom breakout fixture. The flying-lead cable has paired signal and ground lines for each channel to preserve signal quality. Each signal and ground line is designed to plug directly into any 0.1 in. header connector. It is a shielded, 50 Ω cable.
-
Product
Standalone with Drop-In Test Systems
800 Series ATE
-
The Circuit Check 800 Series ATE provides the versatility of utilizing the economical drop-in fixturing present in the 600 Series or an integrated dedicated fixture, while simultaneously providing the increased test equipment capacity of the 1000 Series. This combination produces a cost effective full turnkey test solution.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMK-04
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Efficient And Effective Physical Layer (PHY) Testing Of 10/100/1000Base-T Interfaces
-
Explore Sifos Technologies’ highly unique, plug’n play 10/100/1000Base-T Ethernet Physical Layer Testing Solutions. Cost Effective and Comprehensive PHY Testing without Scopes, Fixtures, Probes, and Test Signals.
-
Product
Control Module
MOC
-
The MOC is our universal control module for a wide variety of tasks, such as controlling relays in the fixture.
-
Product
9050 Rack Mount
-
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
-
Product
Safety Compliance Test System
EN 60601
Test System
Test system for electrical safety compliance testing of medical products in accordance with EN 60601-1, 3rd edition.The system is equipped with three test fixtures which are connected in parallel order to reduce the number of setup tasks for different variants in the course of day-to-day manufacturing processes. Its purpose is to test medical products, e. g. patient monitors, which are employed at hospitals to monitor heartbeat and oxygen saturation.Based on the integrated electrical safety tester by Associated Research, in combination with an AC power source and a switching matrix, it is possible to fully automate tests like for instance AC/DC high-voltage tests, insulation resistance measurements, earth connection tests and leakage current measurements.The required occupational safety is provided by a high-voltage safety hood in accordance with EN 501191. The entire safety technology, as well as the control PC, is mounted in an aluminum-profile cart.
-
Product
Shielding Effectiveness/ Conductivity Test
EM-2107A | 30 MHz – 1.5 GHz
-
The EM-2107A is a standard test fixture for evaluation of the electromagnetic shielding effectiveness of planar material. The fixture is an enlarged section of coaxial transmission line and complies fully with the requirements of ASTM test method D4935-1. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred. The EM-2107A is provided with a reference standard test specimen, a dynamic range specimen. Dynamic range of greater than 80dB is achievable, although the cables and other test system components usually establishes the limiting factors.
-
Product
Manual Test Press Fixture
750/752 Series
-
RTI's manual test presses are compact, portable, all-inclusive, and easy to use. Single lever operation and 100% vertical compression makes the manual test press an ideal solution for PCB, hybrid module, and high pin count device-level testing when complex test requirements cannot be met with a test socket and breakout board alone.
-
Product
DisplayPort™
-
SCHILLER AUTOMATION GmbH & Co. KG
Wilder Technologies Enhanced DisplayPort™ and miniDisplayPort™ test adapters enable Host and Device testing to DP2.1 Specifications. Supporting increasing data rates (UHBR10, UHBR13.5 and UHBR20) to drive 8k displays and higher refresh rates, Wilder’s fixtures provides the a platform for pre-compliance and compliance testing.
-
-
Product
Receiver, G12, 12 Module, With 20" Platform, For Slide Mount (slide Kit Required)
310104334
Receiver
The 20” G12 Receiver is a slide-mounted receiver. The 20” platform provides a large surface for use with large fixtures and supports 180lbs. When used in conjunction with VPC slide mounts and support legs, the Receiver can support 350 lbs. The Receiver is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull down for a reliable connection every time up to 20,000 cycles. The handle can be rotated in 90 degree increments.
-
Product
F9 Systems CalBlade
-
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
Product
10-Ch Pneumatics CAN without RCV module
YAV90PNF
CAN Interface
This pneumatic subsystem is the same as YAV90PNE, but without the VPC receiver module integrated, making it a good option to be used inside the fixture. Since the control is CAN, user can easily place electrovalves inside the fixture without the need to use a bunch of wires.
