-
Product
PXI Fault Insertion Switch, 6-channel, Two Fault Buses, 10 A, Hardware Interlock
40-192A-012-HI
Fault Insertion Unit
The 40-192A-012-HI is a PXI fault insertion switch with hardware interlock using solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test:
-
Product
Automatic Fixture Removal
S93007B
-
The S93007B automatic fixture removal (AFR) is the easiest way to remove fixture effects from non-coaxial device measurements and runs on the PNA/PNA-L/PNA-X Series B model network analyzers
-
Product
10-Ch Pneumatics Selftest Module
YAV90PNT
CAN Interface
Use this module in your self test diagnostics fixture. The YAV90PNT can be used as counterpart of the YAV90PNE, to test that is working properly.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
Test Fixture
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
Boundary Scan Program Development Service
-
No need for test fixtures. Integrates product development, production test, and device programming in one system. Test and Programming data can be reused in Production. Fast test procedure development. Reduced inventory management. Eliminates or reduces ICT usage time. Pre-production testing can begin as soon as prototype is released.
-
Product
Board Test Fixture Probes
-
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
Product
Flash Programming for Functional Test Systems
-
Flash programming stations allow you to offload flash programming from functional test systems, increasing test throughput while improving capital utilization. Circuit Check flash programmer fixtures support multiple programmer types and multiple I/O configurations.
-
Product
Low Noise Test Leads For N1413 With B2980 Series, 3m
N1425B
Coaxial Cable
The N1425B is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425B is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425B enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425B to the B2985B/87B.
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
Pod/Nest Fixtures
-
Nest and Pod Fixtures are used to test components and sub-assemblies. They typically are built in an array and the devices under test are subjected to tests that simulate operating conditions or life-cycle testing. Test Head Engineering is experienced in providing nest and pod testers that meet the connectivity, ergonomic and mechanical requirements of component testing.
-
Product
Standalone with Drop-In Test Systems
800 Series ATE
-
The Circuit Check 800 Series ATE provides the versatility of utilizing the economical drop-in fixturing present in the 600 Series or an integrated dedicated fixture, while simultaneously providing the increased test equipment capacity of the 1000 Series. This combination produces a cost effective full turnkey test solution.
-
Product
In-Circuit Test (ICT) Fixtures
Test Fixture
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
Product
Manual Fixture Kit
230352 – CMK-03
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Test Systems
-
In-Circuit Test (ICT) tests populated circuit boards by means of electronic measurements through thin needles on test fixtures. We offer in-circuit testers for various testing strategies – from the flexible 19“ rack to the ergonomic high-performance tester. And all of our in-circuit testers are also available in the Lambda edition for true parallel testing. The flying probe test checks your printed circuit boards using four movable test heads. This requires no fixtures and allows for flexible test program generation. That makes our flying probe test systems ideal for a high mix of printed circuit boards and small to medium test volumes, such as for prototype testing.
-
Product
In-Circuit Fixtures
-
In-Circuit test fixtures can be configured for dual stage, dual well and opens testing applications. Even the most complex boards can be accommodated using standard methods of actuation.
-
Product
Manual Fixture Kit
230371 – CMCSK-02-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Function Test Fixtures
-
Modulized UUT BFT Test Fixture, Multilevel BFT Fixture, Over Clamp Test Fixture, Rack Mount Test Fixture, Self Contained Pogopin Test Fixture, Simple Low Cost PCBA Test Fixture, Tight Seal Required RF F/T Fixture, and more from IST Engineering
-
Product
Custom Test Connectors and Sockets
-
Custom test sockets are traditionally expensive to build and maintain. To reduce these costs, consider: Using rapid prototyping techniques to build a housing. Using replaceable Z-Axis Connectors. Depending on board layouts and compressed height, these sockets or test fixtures can achieve high numbers of mate/de-mate cycles and operate at GHz frequencies.
-
Product
Parallel Electrode SMD Test Fixture
16192A
Test Fixture
The 16192A test fixture is designed for impedance evaluations of side electrode SMD components. The minimum SMD size that this fixture is adapted to evaluate is 1(L)[mm].
-
Product
VP Power Meter
UVP-365
-
This is the standard measurement instrument to measure absolute UV vaiue. All SAN-EI's UV light source fixtures are measured by this meter.
-
Product
Bottom Electrode SMD Test Fixture
16198A
Test Fixture
Designed for impedance evaluations of bottom electrode SMDs and supports 201 (mm) and 402 (mm) sizes
-
Product
Collins Radar Fixture with Gyro Simulator
TA-3A/B
-
This weather radar test fixture is a combination of the established WXT-250 series fixture and the RDR-2000 and RDR-2100 radars so that a single panel will provide many features that are still required today. The gyro simulator built into the panel is usable for either radar being tested and eliminate's plugging in any external simulator. The features for both product lines as shown in their respecting CMM's are provided on the panel so that full testing and alignment of these radars and their system components can be tested and/or evaluated. If you require any changes or other product versions please give us a call.
-
Product
Custom Test Fixtures
-
For popular high speed components like semiconductor packages, and test contactors, we have developed a custom test fixture which allows the use of high bandwidth microprobes to measure virtually any I/O pin, according to GigaTest's methodology and requirements.
-
Product
Custom Designed Test Fixtures
-
We specialize in automated test systems for both RF and digital devices, modules and systems. Please call to discuss your test requirements.
-
Product
Receiver, G12x, 18 Module, with 20" Platform, for Slide Mount
310104385
Receiver
The 20” G12x Receiver provides rack mounting and tabletop mounting options. The 20” platform provides a large surface for use with large fixtures and supports 180lbs. When used in conjunction with VPC slide mounts and support legs, the Receiver can support 350 lbs. The Receiver is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull down for a reliable connection every time up to 20,000 cycles. The handle can be rotated in 90 degree increments.
-
Product
Radar Altimieter Test Panel for ALT-50/55
TA-55
-
Radar altimeter panel designed after the ALT-50A test fixture. (Ref. Fig. 5-1). Panel allows testing of the indicator or R/T independently or together. An internal power supply is provided to support stand alone testing of the indicator. This panel contains a 4 digit DVM and comes with enclosure. This panel will allow by the book testing.
-
Product
PXI 11-Channel 2A Fault Insert Switch
40-202-101
Fault Insertion Unit
This is the 11 Channel version of the 40-202 Fault Insertion Switch. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test
-
Product
Temperature Probes
-
Lake Shore offers a variety of temperature sensors in packages that enable mounting in very tight areas. But for some applications (especially if the sensors have to be immersed in liquid), you need to do more to protect the sensor circuitry. For these applications, a cryogenic temperature probe is the optimum choice. Encased in one of these stainless steel thermowell fixtures, the sensor can perform as designed, is unaffected by high pressure, and is sealed to keep electrical components and wiring protected from fluids and other elements.
-
Product
Interface Pin
-
Smiths Interconnect offers interface probes for all major test equipment manufacturers. We also provide a variety of interface pins for use in test fixtures.
-
Product
Solar Panel Chamber
-
Specifically designed for the solar industry, these climatic chambers feature specifically designed fixtures to properly measure almost any component related to solar panels including the actual panels, grid-tied photovoltaic inverters, or photovoltaic cells and modules.
