Temperature
a measurement of heat or cold.
-
Product
Inputs Temperature Data Logger – Pt100
HD32.7
-
The instrument HD32.7 is a robust 8 inputs data logger for Pt100 sensor temperature probes. The probes can be Pt100 with SICRAM module, direct 4-wire Pt100 or direct 2-wire Pt1000.
-
Product
Engine Simulator
MS 1118
-
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
Product
8U 21 Slot VME64/64X Enhanced Crate
VME8100
-
short circuit protection, Over / Undervoltage protection, Over temperature protection. Remote monitoring and control take place through CAN bus, Ethernet, USB and RS232 interfaces. The crates are also SBC controlled via graphic OLED Display, provides Automatic Daisy Chain and supports Chained Block Transfers (CBLT). User-friendly control software completes the VME 8100 features. The Unit is powered by 92 ÷264 Vac, 50 ÷ 60 Hz, power factor 0.98% (230VAC).
-
Product
High Pressure Gas Conditioners
HPG
-
Bemco HPG, High Pressure Gas Conditioners are similar to the PTS Portable Temperature Conditioners except they are designed for continuous operation at up to two atmospheres (29.4 psia) of pressure. This higher base operating pressure doubles the gas density per cfm of circulating air or gaseous nitrogen allowing the use of smaller connecting tubes while also increasing thermal capability. .
-
Product
Rugged PC Compatible
SYS-ITX-N-6425E
-
WINSYSTEMS’ SYS-ITX-N-6425E is an industrial embedded computer based on the Intel® Atom™ x6425E Elkhart Lake processor family. It uses less than 12 watts for fanless applications and performs reliably in industrial operating temperatures ranging from -20º to +60ºC. The unit includes a SODIMM socket supporting up to 32 GB of DDR4 system memory and internal mounting support for one 2.5” SATA HDD/SSD. Additional storage is available through MiniPCIe, mSATA, and microSD.
-
Product
Broadband Calibrated Noise Sources
-
Fairview Microwave’s calibrated noise sources cover frequency bands from 10 KHz to 18 GHz. Their performance specifications include output ENR levels ranging from 15 dB to 30 dB and typical VSWR levels as low as 1.25:1. Depending on the model, calibrated frequency points are at 10 MHz, 100 MHz, 1000 MHz, 2000 MHz and 1 GHz steps. The temperature coefficient of these noise sources is < 0.01 dB/°C and noise output variation is < 0.1 dB/%V.
-
Product
Endevco Cryogenic Charge Output Accelerometers
-
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperature gradient. The accelerometers are self-generating devices that require no external power source for operation and contain no electronics. This allows them to operate below the -320° F (-196° C) limit of ICP accelerometers, down to -452° F (-269° C).
-
Product
MeasureLINK™ Software
-
MeasureLINK executes sequences of user-defined experimental steps that can include setting field and temperature levels as well as sourcing and measuring electrical signals. Steps also generate the user interfaces needed to gather inputs before running experiments. You can select steps from MeasureLINK’s editor.
-
Product
CryoPulse
-
Metis Instruments & Equipment NV
Measurements in up to 50 T environments. Cryogenic measurement environment with temperature control from 4K up to room temperature. Modular architecture with easy upgrades to higher energies & higher peak fields. Fast sample exchange possible. Large set of measuring probes for various applications
-
Product
Video Particle Counter with built-in Camera
VPC300
-
Particle Counter with unique built-in camera for capturing videos & photosthat are stored onto internal memory or a micro SD card. The VPC300 canmeasure up to 6 channels of particle sizes plus Air Temperature and RelativeHumidity. Use the included software to generate reports with videos, photos,and data points.
-
Product
Thermal Image Analysis Software
Thermalyze
-
Thermalyze software provides a stable platform from which to perform sophisticated temperature analysis and failure analysis testing. Tools such as Emissivity Tables allow you to perform true temperature mapping on the surface with varying emissivity. Lock-in thermography tests enable you to detect heating below 0.001°C.
-
Product
Temperature & Humidity Chambers
-
Canden Reach-in stability chamber models -Q20,Q40,Q60 is designed to conduct stability testing on pharmaceutical products in accordance with the guidelines set by the FDA/ICH. These chambers play a crucial role in assessing the long-term stability, quality, and shelf life of pharmaceutical formulations.
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
Weather Detection Systems
-
General offers weather detection systems that use a base station to display inputs received wirelessly from remote sensors. The RGR150 can track rainfall amounts as well as temperature and/or relative humidity. WS821 & WS831DL Weather Detection Systems are full-featured wireless weather stations that add wind speed readings and track trends in barometric pressure that can serve as the basis of a short-term weather forecast. Barometric pressure is also available from a dedicated wireless station (the DBAR880), and the original weather forecasterthe ABAR300 Analog Barometer.
-
Product
Micropositioner
-
Our broad range of micropositioners fill requirements for probing for different measurement applications as well as measurement environments. For example, a measurement system focused on cryogenic environments would not use the same product for room temperature probing. Likewise, a DC micropositioner is unfit for mmW measurement applications.
-
Product
Surface Mount Temperature Sensor
SCS
-
The Series SCS Low Cost Current Switches are ideal for monitoring whether fans, pumps, or motors are operating. The current flowing through the core of the device powers the circuit without an external power supply. All models have a built in solid state output and are easy to install. Optional LED's and 10 Amp relay modules are available. The Series SCS is available in both Split and Solid Core configurations
-
Product
Ambient Light Sensors
-
ST offers innovative ambient light sensors (ALS) that provide, in optimized package size, accurate information on ambient light, like the Illuminance (lux) level, the color temperature or the light flicker frequency.
-
Product
Oil-Free HDT & Vicat Tester
HV500
-
The Instron® CEAST HV500 is the latest instrument design to perform HDT and VICAT tests at high temperatures, up to 500°C, making this instrument ideal for research and quality control applications as it is ensuring the capability to test the new generations of techno-polymers, characterized by their excellent properties at high temperature.
-
Product
15W to 60W - Single Output / Multiple Output
DPX Series
-
*Single, Dual and Triple Outputs*9.5-36 Vdc, 18-75 Vdc Inputs*Meets EN55022 Class B*1600 Vdc Isolation*-40 up to 95 °C Operating Temperature*EN61000-4 Immunity*Narrow 24.5 mm width
-
Product
Multipurpose Thermometer With Linearized Ouput
BAT-10/LOP
-
This versatile thermometer has a wide temperature range and can be used in applications as diverse as cryogenic measurements for blood banking and cryosurgery, skin temperature measurements in exercise experiments, liquid measurements in spectrophotometer cuvettes, melting points of plastics and all types of animal and insect temperature measurements.
-
Product
Thermo-Hygrometer
C3121P-2
-
Thermometer, hygrometer is designed for direct measurement of temperature, relative humidity for compressed air up to 25 bars with 2 meters cable. Audio and optical alarm of measured values. Memory of minimum and maximum measured values. Function Hold - manual storing of actual values for later displaying.
-
Product
PXIe-1082, 8-Slot, Up to 8 GB/s PXI Chassis
780321-01
Chassis
PXIe, 8-Slot, Up to 8 GB/s PXI Chassis—The PXIe‑1082 features a high-bandwidth backplane to meet a wide range of high-performance test and measurement application needs. It accepts PXI Express modules in every slot and supports standard PXI hybrid-compatible modules in up to four slots. The chassis features an extended operating temperature range for applications needing cooling performance.
-
Product
Thermapen®
Pro-Surface
-
Measure the temperature of griddles, cooktops, hotplates, and other surfaces with higher accuracy than an infrared thermometer with our new Pro-Surface Thermapen. There are no emissivity adjustments to make or infrared distance measurements to calculate. Simply open the probe and measure.
-
Product
Monitoring Products
-
The motor condition monitoring device with the ability to quantify the status of a three-phase induction motor and incorporating EtherNet/IP communication to trend information on current analysis, motor vibration, motor temperature, and insulation resistance.
-
Product
Probe Card
VC20E Lab
-
*20 millimeter ceramic probe card*Optimized for DC parametric test, modeling and characterization, and single site WLR*Can be quickly installed using an interface tool into various interfaces and takes minimal storage space on the test floor*Effective operating temperature range from -65° to 200° C*Leakage as low as 5fA/V. If you require faster settling time, click here*Can be configured with up to 48 probes
-
Product
WebSensor
T6540
-
CO2 concentration, temperature and relative humidity t-line Web sensor. Remote alarm.
-
Product
Flexible Implantable Microprobe
IT-18EXLONG
-
IT-18EXLONG Flexible Implantable Microprobe with 5 foot lead - Implantable in semi-solids and tissue with 18 gauge needle (supplied). Also for immersion in various solutions and rectal temperatures of small animals. Totally sheathed in chemical resistant Teflon™. Quited rugged. Maximum Temperature 150°C . Isolated. Probe diameter .050" (14 gauge represents the needle gauge that the probe can be inserted through). Time constant 0.3 seconds.
-
Product
Limits and Scanners
-
Watlow Electric Manufacturing Company
Various configurations offer user-selectable or fixed-configuration sensor options including thermocouple, process, RTD and thermal switch inputs as well as user-settable or fixed limit values. Models with displays have user-selectable temperature units. Other features include sensor break protection, industry standard I/O options and UL® and CSA approval. EZ-ZONE models are RoHS compliant. Limits have FM approval for performance in safety limit applications. Watlow limits are designed and manufactured to withstand harsh industrial environments and come with a three-year warranty.
-
Product
4 Digit Field Indicator
CFIA-40 4
-
1. Using LED to display, and able to be used in dark environment2. No external power needed3. Able to display measured value like pressure , temperature and depth etc4. Display solution 1/99995. Isolated alarm open drain output6. Voltage drop will below 4 volt
-
Product
Dynamic Vapor Sorption Analyzer
IGAsorp-XT
-
The IGAsorp-XT is a fully automated water sorption analyzer designed for measurements at temperatures and humidities beyond those available with conventional DVS analyzers. High resolution sorption isotherms are recorded at humidity values from 0.2 %RH or lower, using the unique climate-XT control method. Combined with high temperature water sorption measurements to 300 °C, an integrated pre-heater and completely flexible method programming, the IGAsorp-XT is the world’s most advanced benchtop DVS analyzer.
