Switching
Controls consisting of a mechanical or electrical or electronic device for making or breaking or changing the connections in a circuit. (www.cogsci.princeton.edu)
See Also: Switching Matrix, High Voltage Switching, Switching Matrices, Multiplexers, General Purpose Switch
-
Product
Hybrid LX
HLX Series
-
*Surface Mount Package *Ruggedized, Hi-Rel *Hermetically-Sealed *Extreme Shock and Vibration Tolerance *Fast Switching Designs Available
-
Product
Battery Fault Insertion Unit
Fault Insertion Unit
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
Product
Belt-Pack Transmitter
LMb
-
The LMb transmitter can be configured to operate as a "one touch" device with a single power on/off switch on the top panel, or with full access to all operational parameters using the side panel membrane switches and LCD interface. The top panel switch can also be configured to provide a mute or talkback function.
-
Product
Interface Board for Gigabit Ethernet
40-965-910
Interface
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
Product
PXI Multiplexer, Single 24-Channel, 2-Pole
40-632A-021-24/2
Multiplexer Module
The 40-632A-021-24/2 is a single 24-channel, 2-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
Threaded Pneumatic & Pneumatic Switch Probes
Switch Probe
Narrow place solution - high flexibility - great solution - cost effective.
-
Product
PXI BRIC8 2Resource Distributor, 5Bus Matrix
40-569-125
Matrix Switch Module
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
-
Product
75 Ohm MCX to MCX Cable Assembly
40-977-761-1m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
PXIe Power Relay Module, 12xSPST, 16 A, With Interlock
42-161A-002-HI
Relay
The 40/42-161A-002-HI is a PXI/PXIe 12xSPST power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
PXI 12 x DPST Reed Relay 2.5 Amp
40-136-012
Relay
The 40-136-012 12xDPST reed relay module is part of our range of medium power, general purpose relay modules which are capable of switching voltages up to 200V and current up to 2.5A.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated, 3GHz, 50Ω, MCX
42-873A-101
Multiplexer Module
The 40-873A-101 (PXI) and 42-873A-101 (PXIe) are 4 to 1 RF MUX with 1 bank in a single slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, FC/PC Connectors
40-850A-114
Multiplexer Module
The 40/42-850A-114 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI/PXIe 32x8 High Density Matrix Module, 2-Pole, 2A
42-588-222
Matrix Switch Module
The 40-588-222 is a high density 32x8 2-pole PXI matrix module capable of switching up to 2 A at 220 VDC/250 VAC. The module is in 2-slot format and is constructed using quality electromechanical relays for high switching confidence. A smaller 16x8 2-pole version is also available.
-
Product
PXI 16x2 RF Matrix 300MHz 50 SMB
40-728-001
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
LXI High Density 64x64 2A Matrix
60-552-007
Matrix Switch Module
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
PXI 2 Banks of 80 Channel 1 Pole MUX
40-615-022-2/80/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
Product
PXI 24x4 Matrix, 1 Pole Switching
40-513-021
Matrix Switch Module
The 40-510 series of matrix modules feature a wide range of selectable switching configurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signal routing in ATE and data acquisition systems. Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching signals up to 50MHz. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules.
-
Product
PXI 4 Slot BRIC Solid State 160x8 1-Pole (5 sub-cards)
40-563A-021-160X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe MEMS RF Multiplexer, Dual 4-Channel, 4GHz, 50Ω, MCX
40-878-222
Multiplexer Module
The module is based on the latest micro-electromechanical system (MEMS) switching technology and has low insertion loss and VSWR. In addition, MEMS devices have a long operational life of >3 billion operations and benefit from an operating time of <20 μs allowing greater test system throughput. The multiplexers have excellent and repeatable RF characteristics beyond 4 GHz with each path having a nominally equal insertion loss.
-
Product
Electrical Safety Test Scanner
19200
-
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
Product
PXI 4-Slot BRIC Matrix, 116x8 2A 2-Pole (4 Sub-cards)
40-565B-002-116X8
Matrix Switch Module
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence
-
Product
Pump Laser Diode Driver
S-110
-
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
Product
PXI 8-Slot BRIC 48X8 Matrix, 2A 2-Pole (2 sub cards)
40-565A-102-48X8
Matrix Switch Module
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 464x6, 8 Sub-cards
40-596A-108
Matrix Switch Module
The 40-596A-108 is a PXI 1-pole 464x6 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-596A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 8-Slot BRIC Matrix, 116x8 2A 2-Pole (4 Sub-cards)
40-565B-102-116X8
Matrix Switch Module
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence.
-
Product
Advanced Digital Lab Trainer
-
Designed to do experimentation with Digital & Analog circuits in the laboratory. It is a self contained trainer including Fixed & Variable DC Power Supplies, Pulse Generator with TTL/CMOS, Pulsar switches, etc In a single unit. It is very useful in project work and testing. A number of ready to use experiment circuits boards are available(Optional).
-
Product
PXI 8-Slot BRIC Matrix, 220x4 2-Pole (5 sub-cards)
40-562B-122-220X4
Matrix Switch Module
The 40-562B-122-220X4 is a high density BRIC8 matrix module with a size of 220x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 18xSPST High Voltage Power Relay Module
40-330-002
Relay
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-315-002
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 2m HV, Exit Away From Pin 1
40-970-050-2m-MF-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 24 AWG Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
