-
Product
Power Switches
SMX-2002 (Power)
-
The SMX-2002 is the only switch module in its class with the ability to switch up to 16A. Some applications include: AC line power switching, switching of DC or AC power supplies, control or driving relays for industrial machines (robotics, numerical control machines), automotive engine control, and solenoid switching. Since this module typically switches power to the UUT or interface, the SMX-2002 includes failsafe pins on the front panel which can be configured to open all relays when a failsafe signal is activated. This approach can instantly removes all power to the UUT or interface.
-
Product
PXI Solid-State Switch Module, 3xSPST, 25 A, 100 V
40-184A-002
-
The 40-184A-002 has 3-off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
PXI Mixed Configuration Relay Module - 13 Cells Populated
40-138-AA-BB-CC-DD (13 CELL)
-
The 40-138 2A Relay Module with 13 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
-
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
Product
Active Switching Power Supply Using Mosfet, 125 KW, P/N 5940C2
-
- Active Switching Power Supply Using MOSFET, 125 KW, P/N 5940C2- Input: 480 VAC, 150 Amps, 3 PH, 60 Hz- Output: 0 to 50 VDC, 2500 Amps max- Ten modules in parallel, each module is rated for 0 to 50 VDC, 300 Amps- PLC Control provides Positive Polarity, Negative Polarity and Shuts OFF- Start / Stop capability and EPO- Output voltage and current are displayed on the voltmeter and ammeter- PLC supplied by the customer. We provide a PLC interface only- Indoor enclosure dimensions: 65″W x 50″H x 36″D or (TBD)- Estimated weight: 2000 lbs. or (TBD)
-
Product
LXI Remote AC Power Management Switch
-
If you have ever read the term "programmable except for the supply on/off switch", Pickering's LXI remote AC power management switch can provide this additional capability in a system with the added benefit of an easy to use LXI interface. This power management switch provides a means of remotely controlling the power status of up to eight instruments in a system through an LXI enabled power management switch. Additionally, the Power Management Switch is available as an RS232 serially controlled version.
-
Product
Optical Receiver
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Return path optional. Frequency splitting according to customer’s need.* 2 RF outputs, level ≥104dBμV when optical input @ -1dBm.* Output level tunable through buttons on front panel.* RF Test Point on front panel.* High quality switch power supply.
-
Product
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 12 V, 0 A, 30 A
T3PS11230
-
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 12 V, 0 A, 30 A.
-
Product
PXI Power Relay Module, 12xSPST, 16 A
40-161A-002
-
The 40/42-161A-002 is a PXI/PXIe 12xSPST power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
Product
60-Watt DC/DC Converter, 3U cPCI
55KQ2-02
-
NAI’s 55KQ2-02 is a 60 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 60 Watts. It is designed to work along with NAI’s 72.5 DC Power Line Conditioner w/Holdup companion unit, model 44KS3-02.
-
Product
High Power Switch and Bias Module
-
Macom Technology Solutions Holdings Inc.
MACOM’s High-Power Switch and Bias modules are extensively used in 4G and 5G TDD base stations as well as aerospace and defense applications. The PIN Diode Switch features high power handling, low insertion loss, and super board band performance. The integrated bias controller utilizes a boost circuit and provide the driver circuitry to the switch. The modules require only a single 5 V supply, and a single TX / RX control signal which greatly reduced the customer design complexity.
-
Product
Wires and Pipe Locator
LKZ-720
-
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
Product
Power Supplies
-
ICP DAS USA offers the latest Din-Rail mount and panel mount switching power supplies! The ICP DAS USA power supplies are available in a variety of configurations, and ideal for almost any industrial control or data acquisition application!
-
Product
PXI High Voltage Power Multiplexer, Single 24:1
40-331A-001
-
The 40-331A-001 single 24:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
Product
Fanless Embedded System With Intel® Celeron® J1900, HDMI, VGA, 2 GbE LAN, 4 USB, 3 COM And 10 To 34 VDC
eBOX626-842-FL
-
The eBOX626-842-FL is the energy-efficient fanless embedded box PC suited for rugged and extreme applications with its extended temperature and wide range voltage capability. The extreme compact box PC utilizes an onboard Intel® Celeron® quad core processor J1900 2.0GHz (codename: Bay Trail-D) to boast both excellent performance and ultra-low power consumption. The ultra-slim fanless embedded computer supports system memory up to 8 GB with one DDR3L-1066/1333 SO-DIMM socket and offers HDMI and VGA display outputs, offering not only high computing capability but also excellent graphics performance. Integrated single-chip design, the brand new ruggedized embedded system is lighter and thinner compared to previous eBOX620 series. Supporting wide operating temperature between -20°C to +55°C and 10 to 34VDC wide DC input voltage, the fanless embedded PC is excellence for wide range of industrial applications. Its passive cooling design also offers quiet, fanless operation with low power consumption, and all at an attractive price point. With full-featured of I/O interfaces, the Intel® Celeron®-based eBOX626-842-FL supports two RS-232/422/485 ports, one RS-232 port, VGA, HDMI, audio, dual Gigabit Ethernet LAN ports, four high-speed USB 2.0, three SMA type connector openings for antenna, 10-34VDC power input connector, and one ATX power switch. One 2.5" SATA HDD drive bay and mSATA are also embedded in the embedded computer to possess sufficient storage.
-
Product
75/150-Watt DC/DC Converter w/Holdup, 3U cPCI
75PS4
-
NAI’s 75PS4 is a DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This programmable, switching power supply accepts a +28 VDC input and is available in either a 75 Watt or 150 Watt-version.
-
Product
PXI Power Relay Module, 10xSPST, 16 A
40-161A-003
-
The 40/42-161A-003 is a PXI/PXIe 10xSPST power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
Product
Saluki SEL7 Series Programmable DC Electronic Load (up to 6kW)
-
The new SEL7 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL7 series delivers high speed and high accuracy with a resolution of 0.1mV and 0.01mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL7 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.
-
Product
Chassis - Up to Four 8x1 Modules, Eight 4x1 Modules or Mixtures of 8x1's, 4x1's, 2x1's & 2x2 Modules in Any Combination or Configuration
CXAR/32-MF
-
These Chassis controls up to four 8x1 modules, eight 4x1 modules or mixtures of 8x1's, 4x1's, 2x1's and 2x2 modules in any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules and a Control Module to complete the system. Pushbutton manual control is optional.
-
Product
Switches-SP3T
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer an extensive collection of switches covering multiple commercial and aerospace and defense markets. Our product portfolio has a broad frequency spectrum from DC to 70 GHz. Our silicon Heterolithic Microwave Integrated Circuit (HMIC) PIN diode process is ideal for high power and broadband switches operating from 50 MHz to 26 GHz. Our AlGaAs PIN diode process can extend the upper frequency range of our switch die beyond 70 GHz and is ideal for instrumentation and radar applications. Our GaAs pHEMT and MESFET technology is ideal for fast switching and low control voltage switches optimized for both narrow band and broadband applications. Our 75 Ohm absorptive switches are designed specifically for demanding CATV, FTTx and DBS Infrastructure and CPE applications.
-
Product
Form A Circuit Board 80 Channel, 300 VDC, 2 A
OTP2 module no.195
-
The 40-139 2A relay series is suitable for applications requiring medium power, high density switching. With a current capacity of 2 A and voltages up to 300 VDC / 250 VAC, it is suitable for cost-critical applications.
-
Product
30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP030
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
PXI Power Relay Module, 16xSPST, 16 A, With Interlock
40-161A-001-HI
-
The 40/42-161A-001-HI is a PXI/PXIe 16xSPST power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
6TL-3X INLINE Header Conveyor 765 mm Length
AQ580
-
- PCB up to 600mm length 400 mm width- Programmable transfer speed up to 1 m/s- Automatic Previous/Next speed adjustment- 2D Code reader w/automatic positioning- Pre-wired for second 2D Code reader- Automatic width setting- PC for line management w/UPS with 20” monitor and keypad in adjustable position arm- 24 Ports PoE Switch- Power inlet rack with current protections and line safety relay- Top cover and door w/safety contacts inhibiting line modules while active- Mechanisms self-test- Width auto-adjustment and cyclic width- Non-contact electronic stop of the PCB- 4U Free on the 19” Rack- Interfaces SMEMA 9851 y IPC-HERMES 9852- CE certified
-
Product
Differential Voltage Probes
DP150/DP200pro
-
The DP differential isolation probes are an important accessory for any laboratory involved in power electronics and high voltage systems. These probes allow isolated and floating measurements with any oscilloscope or data recorder, whilst the oscilloscope can remain grounded. Using a DP150 or DP200pro probe, differential and floating measurements can be made on a variety of ac power systems like 230V/110V ac input power supplies, chopped and switching power supplies, thyristor controllers, variable speed motor drives (PWM signals), motor inrush current and measurement across current shunts. The isolated input is made via two 4mm/banana safety sockets. The BNC output allows easy connection to an oscilloscope. The DP probes can be powered from a 9V battery or external power supply.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-500B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Chassis - Control Relays Greater than 8x1 or Control Multiple Relays in Series Forming Larger Switches than Normally Possible Such as 16x1 to 32x1 Sections.
CXM/256-MF
-
These Chassis are typically used to control relays greater than 8x1 or control multiple relays in series forming larger switches than normally possible such as 16x1 to 32x1 sections. Or control mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 256 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
Product
500A AC/DC Current Sensor
CT6904
-
Hioki pull-through AC/DC current sensors are best-in-class devices for use with power analyzers,, Memory HiCorders and high performance oscilloscopes. The CT6904 is a DC to 4 MHz/500A sensor, ideal for capturing current signals from switching power supplies, inverters, power conditioners, etc.
-
Product
16FE + 2GE Combo Port Unmanaged Switch
EKI-2718E-2CI
-
Provides 16FE+2GE combo port with Auto MDI/MDI-X, Supports 16 x 10/100 Mbps Auto-Negotiation + 2 x Combo 10/100/1000M Auto-Negotiation, Supports redundant 12 ~ 48 VDC power input.Supports DIP Switch Configuration: QoS/BSP/port-based VLAN.
-
Product
Universal Switch
34980A
-
34980A Universal Switch Module 34937A, 34938A can be used to send signals or control other devices in the application. The 34937A is a versatile universal switch with 28 channels capable of switching up to 1A. In addition, there are four can switch up to 5A of the A-channel. The 34938A has 20 5A channels of type A topology. Each type A general-purpose switch can withstand up to 150W of power per channel, suitable for power switching.
