-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
50-Pin SGMC Connector to Connector for Pickering Products
-
Our 50-Pin SGMC connector is used on PXI power switching products to provide a high current user connector solution with high density.
-
Product
Switching Power Chargers
-
JYUE LII INTERNATIONAL CO., LTD.
A&V power transformer supplies and manufactures certified switching power charger with industrial UL / cULus / CB / CE / TUV & ISO 9001:14001 certified electrical products and manufacturing facilities based in Taiwan. Switching Power Charger Includes C02 Series, C05 Series, C06 Series, OP Series, C07 Series, C08 Series, MDA Series, LN Series Switching Power Charger
-
Product
PXIe Power Relay Module, 10xSPST, 16 A, With Interlock
42-161A-003-HI
Relay
The 40/42-161A-003-HI is a PXI/PXIe 10xSPST power relay modulewith optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
PXI High Voltage Power Multiplexer, Hex 4:1 (SP4T)
40-331A-004
Multiplexer Module
The 40-331A-004 hex 4:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
Product
Power-Switching Test System
High Voltage Switching Test System
-
The Accel-RF Power-Switching Test System is capable of measuring reliability under a variety of conditions for switching power applications up to 1kV (off) and 25A (on) at rates up to 1MHz switching frequency, dependent on voltage. By leveraging technology developed for the RF burn-in tray platform with new fast switching measurement techniques, this system can support testing of multiple devices under elevated temperature stimulus in a small physical area, and offers the flexibility to test both soft- and hard-switching applications. The Accel-RF Power-Switching System is the most flexible and accurate power switching platform available.
-
Product
PXI Twelve 2:1 High Voltage Power MUX
40-331-006
Multiplexer Module
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
600-Watt DC/DC Converter, 6U VME
64PS1
DC Converter
The 64PS1 is a 600 Watt DC/DC Converter that plugs into a 6U VME chassis with an 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts a +28 VDC input and provides a single output at 600 Watts continuous or 1,000 Watts peak.
-
Product
Amplifier
C-Band
-
Amonics offers polarization maintaining EDFAs for various applications. Including free space communications, coherent beam combining, and detection system. The output light is linearly polarized with high polarization extinction ratio. The compact turnkey benchtop or 19" rackmount instrument incorporates a user-friendly front panel housing with a LCD monitor display, key switch, power adjust control knob and optical connectors. A RS232 or Ethernet computer interface is also equipped.
-
Product
PXI Solid-State Switch Module, 3xSPST, 1.5 A, 400 V
40-185A-002
Switch Module
The 40-185A-002 has 3-off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions.. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
PXI/PXIe High Voltage Power Relay Module, 14xSPST With Hardware Interlock
42-323-901-HI
Relay
The 40-323-901 (PXI) and 42-323-901 (PXIe) are 14xSPST relay modules suitable for applications requiring high voltage power switching with high density. They have current handling up to 0.25 A, cold switching up to 9 kVDC/9 kVAC peak and hot switching up to 7.5 kVDC/7.5 kVAC peak.
-
Product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
-
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
Product
PXI Solid-State SPST Switch, 6-Channel 25A 100V
40-184-001
SPST Switch
This range of PXI high power switches support 6-off high current SPST switches into two PXI slots or 3-off high current SPST switches into one PXI slot. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each PXI solid-state SPST switch can support 25A of continuous current and switch up to 100V signals. The switch can sustain inrush currents of up to 90A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1200B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Power Switches With USB Charge Controller
-
ST’s USB charger emulator family (STCC) features ICs integrating a power switch, a data switch and an intelligent charge controller. It supports most charging schemes on the market (standard and proprietary) to ensure compatibility with a broad range of portable devices. ST’s unique and patented attach detection mechanism makes the STCC family ideal to guarantee fast and accurate charging while preserving the host battery.
-
Product
FaithTech FTG Series Modular High-power Programmable DC Power Supply (4~600kW)
FTG Series
-
Shenzhen FaithTech Technology Co., Ltd.
FTG series programmable DC switching power supply, voltage range from 10V to 1500V, single current up to 12000A, single maximum power of 600kW. The first technology in China, it still maintains 0.1% control and measurement accuracy when working with high current, providing strong support for sensor testing, superconducting material testing, cable testing and other tests.
-
Product
PXI Power Relay Module, 12xSPST, 16 A, With Interlock
40-161A-002-HI
Relay
The 40/42-161A-002-HI is a PXI/PXIe 12xSPST power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
50-Pin SGMC Connector & Cable Accessories
-
Our 50-Pin SGMC connector is used on PXI power switching products to provide a high current user connector solution with high density.
-
Product
PXI 2A Relay Module 80xSPST
40-139-101
Relay
The 40-139 2A Relay Series is suitable for applications requiring medium power switching with high density. Featuring 2A current capacity and voltages to 300VDC/250VAC it is useful for cost critical applications.
-
Product
DataComm & LAN Testers
-
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
Product
Power Supplies
-
ICP DAS USA offers the latest Din-Rail mount and panel mount switching power supplies! The ICP DAS USA power supplies are available in a variety of configurations, and ideal for almost any industrial control or data acquisition application!
-
Product
Shunt Regulators
-
These are the standard reference voltage source widely used by the feedback circuits of switching power supplies. Compared to the Zener diode, which is a discrete product, a shunt regulator has much better voltage precision because voltage control is carried out as an IC.
-
Product
Chassis - Control Relays Greater than 8x1 or Control Multiple Relays in Series Forming Larger Switches than Normally Possible Such as 16x1 to 32x1 Sections.
CXM/256-MF
Chassis
These Chassis are typically used to control relays greater than 8x1 or control multiple relays in series forming larger switches than normally possible such as 16x1 to 32x1 sections. Or control mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 256 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
Product
Load Switches
-
Analog Devices load switches provide a highly integrated solution for switching voltage rails on in a controlled manner via an internal, high-side switch. This portfolio features overcurrent and overtemperature protection and supports currents up to 3 A. They provide a very low pass element RDSON to reduce power losses. The combination of the functionality and integration levels of ADI load switches make them extremely well-suited to inrush control applications for pluggable optical modules, line side pluggable interfaces protection, power plane switching, and power rail sequencing applications.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1000B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Optical Receiver
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Return path optional. Frequency splitting according to customer’s need.* 2 RF outputs, level ≥104dBμV when optical input @ -1dBm.* Output level tunable through buttons on front panel.* RF Test Point on front panel.* High quality switch power supply.
-
Product
30A, 50MHz High Sensitivity Current Probe
CP030A
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP031
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Switch Indication Maintainer Plus
The SIM-Plus
-
The SIM-Plus - Switch Indication Maintainer Plus is a handheld device used to simulate normal switch correspondence while performing periodic maintenance or testing. The SIM-Plus also provides the ability to power the switch machine using local switch battery or, if battery is not available, provide a temporary source of power from an optional power pack.
-
Product
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 24 V, 0 A, 15 A
T3PS12415
Power Supply
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 24 V, 0 A, 15 A.
