DC/DC Converters
Takes DC input and then provides regulated and/or isolated DC output.
-
Product
Keysight 4-Channel D/A Converter with Waveform Memory for 34980A
34951A
Digital / Analog Converter
The Keysight 34951A module for the 34980A Multifunction Switch/Measure Unit has four electronically calibrated analog channels that can output up to +/-16V DC or +/-20mA DC with 16 bits of resolution. Each channel can be updated individually with a 200 kHz update rate. You can use the standard waveforms provided or create your own with over 500,000 points. These points can be dynamically allocated among one or more channels and output as a point-to-point arb.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-RDC 20
Digital / Synchro Converter
Computer Conversions Corporation
SDC & RDC 20 BIT Synchro / Resolver to Digital Converter
-
Product
8 channel 16 bit Digital to Analog
CPCI-DA8-1
Digital / Analog Converter
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA8 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
Product
Synchro to Digital-Resolver to Digital Converters
MRDC
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions’ MRDC64-3 is a miniature single chip solution for providing a complete 1 x 64 speed resolver interface into any demanding industrial or military application.
-
Product
Synchro to Digital-Resolver to Digital Converters
HSDC-HRDC
Digital / Synchro Converter
Computer Conversions Corporation
HSDC & HRDC Series are Miniature, Tracking Synchro and Resolver to Digital Converters with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command for military and industrial applications.
-
Product
Synchro to Digital-Resolver to Digital Converters
Synchro- Burst
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions Corporation's Synchro-Burst is a complete 2 channel Synchro to encoder interface designed to easily integrate inherently absolute rotary synchro, resolver or linear LVDT position sensors into motion controls and counters that are normally only designed to facilitate incremental encoder feedback.
-
Product
HCU/DC-DC Converter ATS
8900
DC Converter
Low power testSleep mode current testInput overvoltage limit testLine regulation testEfficiency testLoad regulation testOutput ripple voltage testDC-DC load testOvercurrent testPower doen and isolation test
-
Product
Digital to Synchro Converters
DSP
Digital / Synchro Converter
Computer Conversions Corporation
The DSP Series are high efficiency, AC Reference powered, Transformer Isolated, continuously updating “whole” Digital to Synchro Converters, designed for high performance Military and Industrial applications.
-
Product
Analog-to-Digital Converter Board
VME-3125A
Converter Board
Isolated Scanning 12-bit 32-Channel Analog-to-Digital Converter Board (6U) with Built-in-Test (BIT)
-
Product
Digital to Synchro Converter
DSPH
Digital / Synchro Converter
Computer Conversions Corporation
The DSPH Series High Power Digital to Synchro Converters, are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and instantaneous absolute position indicating and active control systems.
-
Product
1000 Watt AC/DC Power Converter, 6U VPX
VPX56H-6
DC Converter
The VPX56H-6 is NAI's latest high power, 1000 Watt AC/DC converter which accepts either a 3Ø 115VAC L-N inputs or a +270 VDC input. It plugs directly into a standard 6U VPX chassis with a (VITA 62) 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Optical-Electrical Converter - PXI
O2E 1000 – 1400 Series
Optical / Electrical Converter
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
Product
DCDC
JA/JP Series
-
The 15-Watt JA/JP series operates over an ultra wide range of 9-36 Vdc or 20-72 Vdc. Efficiencies of 80% are typical over varying load conditions of 25% to 100%. Additional features include input reverse polarity protection, remote on/off control, logic compatible with CMOS or open collector TTL, short circuit protection with auto restart, overvoltage protection, and an operating temperature range of -25°C to +71°C with no derating. Units are packaged in a six-sided continuous shielded case for EMI/RFI protection and measure 2.0” x 2.0” x 0.40”.
-
Product
DC Electronic Load
63600 series
-
Chroma's 63600 series DC electronic loads are designed for testing multi-output AC/DC power supplies, DC/DC converters, chargers, batteries, server power supplies, and power electronic components. They are excellent for research, development, produc t ion, and incoming inspection applications. The 63600's state of the art design uses DSP technology to simulate non-linear loads using a unique CZ operation mode allowing realistic loading behavior. The 63600 series can draw its rated current under very low voltage (0.4V typical). This unique feature guarantees the best loading performance for modern Point-of-Load conditions and fuel cells.
-
Product
Dynamic D/A Converter, 16-channels, 16-Bit, Unipolar, 30 V/20 mA
M9188A
Digital / Analog Converter
The M9188A is a PXI based, 1-slot unipolar Dynamic DAC which has 16 channels capable of supplying typical waveforms at high voltages. It has 4 isolated banks with 4 channels in each bank.
-
Product
DC/DC Power Supplies
-
Industrial DC/DC power supplies designed to operate at extended temperatures from -40 to +85C
-
Product
DC/DC
-
The PPM-DC-ATX-P is a PC104-Plus module that produces five regulated DC voltages from a common DC input. It features a very wide voltage input range from 10 to 50 volts.
-
Product
AC-DC Rectifier / Converters
DC Converter
These following AC-DC converters all can provide 3.3/5/9/12/25/24/28/48V etc output. Newly acquired 2U rack mount 48V rectifier is a mature solution for 48V telecom systems.
-
Product
DC/DC Power Supply
ISM-DC-AT512-P
DC Power Supply
The ISM-DC-AT512-P is a dual output, DC/DC power supply designed for small form factor embedded systems. It features a very wide voltage input range from 10 to 50 volts DC. This allows the unit to operate with 12, 24, or 48 volt battery or distributed DC power systems. It opens up a wide array of applications including transportation, Mil/COTS, security, solar-powered, and telecommunications.
-
Product
DC-DC High Performance
CPZ 32nd Brick Series
-
The high efficiency of the CPZ series allows for no minimal derating over a wide ambient temperature range.
-
Product
Signal Converters
-
ams signal converters contain four or eight signal channels, and can be dynamically programmed in-process by means of multiple amplification levels. This makes them very well suited for multi-channel sensor systems in applications with dynamic amplification and a high sensor bandwidth. All the converters small: they are available in space-saving (Q)SOP packages or as Chip-on-Board(COB) packages.
-
-
-
Product
Interface Converter
ZET 7174
-
*Interface converter USB↔CAN 2.0*Digital sensors and controllers power supply*Data exchange with PC
-
Product
Communication Converter
F485
-
The F485 is a self-contained device for converting between RS232, RS485 and fiber optic signals. The F485 is electrically isolated to improve communications in noisy environments. The converter uses internal switches to select the signal conversion type and communication rates up to 57600 bps. The F485 converter uses the data on the serial ports to determine direction and therefore requires no hardware handshaking signals from the computer.
-
Product
Up Converters
-
Macom Technology Solutions Holdings Inc.
MACOM's upconverters are widely used in point-to-point radio, broadband communications, and RADAR applications. Operating up to a frequency of 86 GHz, our upconverters feature an integrated image reject (balanced) mixer, LO buffer, and RF buffer. Some products also include LO multiplication and variable gain, all within a single chip. Available in die, or SMT lead-free QFN and LGA packages, our upconverters boast excellent performance with adjustable bias, high linearity and image rejection with low LO leakage
-
Product
Frequency Converter
A6000-E1
-
The Quartzlock A6000-E1 is a 1U rack mount, frequency converter for use with frequency standards such as rubidium, cesium, or hydrogen maser standards. Sine wave outputs are provided at frequencies of 2,048 kHz
-
Product
UP Converter
-
The products have a big Dynamic Range, are highly linear and have low Noise Figures to keep the best possible quality of the signals to be converted. For this reason an internal filter for secondary wave suppression is implemented.
-
Product
SCSI Converters
-
Paralan's wide product line of SCSI Converters permits different SCSI Bus types to communicate with ease and reliability, and with no loss of data throughput.
-
Product
DC/DC Power Supplies
-
Astrodyne TDI’s line of DC/DC power solutions provide both a high performance and cost effective power conversion solutions for a variety of applications where efficient distributed power is required. The Astrodyne TDI team can help you find a solution that meets your specific requirements
