DC/DC Converters
Takes DC input and then provides regulated and/or isolated DC output.
-
product
Data Converters
Maxim's portfolio of data converter ICs is one of the largest in the industry. We offer a wide range of data conversion ICs including some of the highest performance analog-to-digital converters (ADCs) and digital-to-analog converters (DACs) on the market today.
-
product
Low Noise Converter for Radio Amateurs
The concept of software defined radios (SDR's) is becoming increasing popular in both commercial, military and Amateur Radio circles. In their basic form, the use simple front end filtering followed by a Quadrature Sampling Detector (QSD) with the post detection processing done in software using the sound card found in PC's. Several popular kits have been developed to introduce Amateurs to the concept.
-
product
WIFI Converter
When MRC meter with RS232 interface is connected to RSW-914, the meter can share data via WiFi technology. Therefore, personal devices, like desktop, laptop, smart phone, tablet... with WiFi function can be read the measuring data via WiFi. For example if factory installs Power analyzer DW-6095 along with RSW-914, then operator can monitor the power information (measuring value ) via WiFi network with safety.
-
product
Voltage Converters
Made from marine-grade aluminium extrusions or heavy-gauge aluminium sheet metal. Powder-coated or anodized, and use stainless fittings throughout Fitted with robust circuit boards using expensive heavy-gauge copper conductors, designed by Analytic Systems' engineers and assembled in our plant.Models are available to step-up, step-down, stabilize or isolate DC power over a range of 12 to 360 volts. No matter which unit you need, these easy-to-install Voltage Converters will give you many years of reliability.
-
product
D/A Converter
DA-4130
The DA-4130 D/A converter converts BCD output signal from Ono Sokki's digital gauge DG-4000 series, RV series reversible counter or other devices into analog signal to be recorded with pen recorder, etc.
-
product
Pulse Rate to 4-20mA or Voltage Converter
SY020
The SY020 Pulse Rate Converter can be linked to any frequency generating device e.g. flow meters, which gives TTL, pulse Reed switch or coil output, converting the frequency to an analogue signal. This can be 4-20mA loop current or a voltage output. The 4-20mA version unit is loop powered.
-
product
Digital to Analog Converter
20-bit digital-to-analog (D/A) converter offering 20-bit monotonic performance over the specified temperature range. It utilizes delta-sigma technology to achieve inherently linear performance in a small package at very low power. The resolution of the device can be programmed to 20 bits for Full-Scale, settling to 0.003% within 15ms typical, or 16 bits for Full-Scale, settling to 0.012% within 2ms max. The output range is two times the external reference voltage. On-chip calibration circuitry dramatically reduces low offset and gain errors.
-
product
D/A Converters
Renesas' high-speed, low-power, digital-to-analog data converters (DAC) are ideal for communication systems, medical/test instrumentation and equipment, and video applications.
-
-
product
Adapter / Carrier Converter Card
PCIBPC104pET
PCIBPC104pET adapter / carrier converter card provides the ability to install 1-4 active PC104p or PCI-104 cards into a standard PCI slot. PCIBPC104pET has a PC104p and PCI-104 compatible stack position mounted to a universal voltage shorter than 1/2 length PCI card. The PC104p position is stackable with all 4 active positions usable.
-
product
Signal Converters For High-accuracy Angular Measurement
EIB 1500 series
*Interpolation and digitizing electronics for the real-time digital processing of positions from two scanning heads*Input: incremental rotatory HEIDENHAIN encoder with two scanning heads and distance-coded reference marks (relative orientation of scanning heads: 180° ± 5°)*Output: EnDat 2.2, Fanuc Serial Interface, Mitsubishi high speed serial interface*Integrated subdivision: 16 384-fold
-
product
Standard High Speed D/A Converters
Analog Devices digital-to-analog converter (DAC) portfolio provides solutions for your high speed and precision DAC applications. Thanks to complete data sheets and evaluation boards, as well as broad support among our clock and timing, RF, power management, and op amp portfolios, our DACs can help you reduce time to market and system design costs. A high speed range from 30 MSPS to multi-GSPS, 8- to 16-bit resolution, and a tiny package are just some of the features that make our industry-leading d/a converters stand out.
-
product
5VDC Sensor Converter, 5VDC, 15mA
ENVIROMUX-S5VDC-5V
External RJ45 device monitors up to two linear DC sensors, 0VDC ~ 5VDC. Output for each sensor: 5VDC, 15mA. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,956,288 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
product
DC-Angle to Synchro or Resolver Converters
LDS & LDR
Computer Conversions Corporation
The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.
-
product
Signal Converters
On one hand, there are signal converters which transform an input frequency range into an analog signal. These signal converters are very easy to program and control. Other signal converters can transform analog input signals into analog normalized signals with galvanic insulation. Due to the fact that these signal converters can be freely graduated, they offer endless possibilities and 110 combinations can be selected by means of a DIP switch. Other kinds of signal converters can be connected to devices with RS-232, RS-485 or RS-422 protocols.
-
product
Interface Converter
ZET 7177
ZET 7177 CAN→GSM interface converter can be used under conditions when there is no access to a regular connection over Ethernet, or when you need to provide a redundant channel in case of Ethernet fouling.
-
product
LVDS To DVI-D Converter Board
AX93221
*Input supports 18/36/24/48-bit LVDS through 40-pin LVDS connector*Output supports DVI-D connector*Size: 60 x 50 mm*Applied for PICO821 and PICO822
-
product
Frequency Block Converter
FBC
The FBC-XX-FB is a full band system can be built upon a Keysight N8975A Noise Figure Analyzer (NFA) or X Series Signal Analyzer with option N9069A. This system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device covering Ka, U, V, E, W bands (26.5-170 GHz), when used with an Agilent E8247C signal generator (or equivalent).
-
product
4-20mA Converters
4026
SPECTEC Innovative Sensor Solutions
Model 4026 Freq to Voltage or Freq to Current Converter accepts frequency input from any magnetic speed sensor, digital magnetic pickup or Hall effect zero speed sensors. Input and output configurations are field selectable. Input range is adjustable between 1100 Hz - 10 kHz or 75Hz to 1100 Hz. Output selection can be configured as 4-20mA converter, 10-50mA converter, 0-5 V FTV converter or 0-10 V FTV converter. ZERO and SPAN adjustments easily calibrate to almost any measurement range, with little interaction between the adjustments.
-
product
CAN + OBD Network Data Converter
NC2
Add Vehicle Network based Data Acquisition to your existing fleet data acquisition systems for under one thousand dollars with the NC2. Great for NVH Tachometer applications.
-
product
Balanced O/E Converter
TIA-527
The TIA-527 balanced optical to electrical converter provides adjustable gain and a bandwidth of DC to 125 MHz. It is useful for coherent heterodyne detection applications, spectroscopy and similar applications for which the ability to discern small variations in signal strength in two optical paths is critical..
-
product
DC Converter
Primary switched DC converter modules are used, among other things, to generate different (consumer) voltage levels from central DC voltages, also battery-supported.
-
product
- RS-232 to RS-422 Interface Converter
Model 263
No AC or DC Power; Full Duplex RJ-11 and Screws; Surge Protection. The Model 263 power stealing RS-232 to RS-422 interface converter offers the user the benefits of other Telebyte converters without the problem of supplying power. With only TD, RD and Ground the Model 263 will provide operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
product
Modular Multilevel Converter (MMC) Test Bench
Research into innovative HVDC interconnections and FACTS applications requires a flexible hardware architecture that allows testing of new topologies and switch configurations.
-
product
SAR A/D Converters
Renesas offers a large selection of successive approximation register (SAR) analog-to-digital converters (ADCs), ideal for most medium-bandwidth signal acquisition applications.
-
product
HD Audio Converter Board With Bracket
AX93242
*HD audio converter board with bracket*For SBC81205, SBC81206, SHB101 and SHB210*Mic-in/CD-in/Line-in/Line-out/Speaker-out
-
product
High Power Frequency Converter
BL+ Series
Behlman's BL-PLUS Series High Power AC Source/ Frequency Converter provide the performance of a linear with all the benefits of a switching amplifier. Instead of relying on large, noisy motor generators for AC power, today's testing facilities are switching to quiet, compact Behlman AC Power frequency converters.
-
-
product
RS232 / RS485 / RS422 / TTL Serial Converters
Rated to perform at temperatures between -40°F and 185°F (-40°C and 85°C), our rugged industrial-grade RS232 / RS485 / RS422 / TTL serial converters are almost indestructible. These industrial-grade serial converter products support multi-drop RS485 / RS422 networks and come with 600W surge protection, 15KV ESD protection, selectable end-of-line terminators, and optional 2500V opto-isolation circuitry, which ensure crisp data signals without interference for all types of installations.
-
product
Modbus to Profibus Converter
P485
The P485 Modbus to Profibus Converter acts as a gateway between a Modbus RTU network and a Profibus-DP network. Integration of Modbus devices into Profibus networks is enabled without loss of functionality, control, and reliability, both when retrofitting to existing equipment as well as when setting up new installations. The P485 Modbus to Profibus Converter is an external DIN-rail mounted device which provides Profibus network connectivity to Modbus devices via a serial RS232/RS422/RS485 interface.
