Fault
-
product
Modular Breakout System 8-Pin Power D-type Plugin Module
95-191-002
The 95-191-002 Plugin Breakout Module is designed to be fitted to a PXI 40-191 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
PC Based Rotor Tester
GTS 1000
The PC Based Rotor tester is the most reliable, fast and cost-effective way to detect faults in the Rotors in less than 10 seconds. This Rotor Tester can Test Large sized Rotors of any Size, Length & Weight that can be mounted on a Load balancing machine or a Lathe and rotated at a speed of 600 rpm.
-
product
Thermal camera
An efficient way to prevent faults in circuits or facilities by locating hot spots, as well as in veterinary medicine or location of living beings.
-
product
PXI/PXIe Fault Insertion Switch, 74-Chan 2A, N/C Through Relays, Fault Buses on M & U
40-190C-012
The 40-190C-012 (PXI) and 42-190C-012 (PXIe) are fault insertion switches with 74 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Ground Fault Monitor
IFT-120
Our ground fault monitors enable you to easily and quickly find the source of the fault before a major problem occurs and damages your equipment. This is the IFT-120, designed to assist you in rapid identification of ground faults.
-
product
PXI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs, Isolated PXI Digital I/O Module
779313-01
16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs, Isolated PXI Digital I/O Module—The PXI‑6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. For added safety, the PXI‑6521 requires a keyed connector. If a computer or application fault occurs, the PXI‑6521 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
product
Pen-type Visual Fault Locator
PVLS Series
Shanghai Tarluz Telecom Tech Co., LTD
PVLS Series Pen-type Visual Laser Source (VFL) is specially designed for field operators who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes threen main functions, Finding the breakpoint, poor connections, bending or cracking in fiber optic cables, Identifying the faults of OTDR dead zone, End-to-end visual fiber identification.
-
product
PXI BRIC8 FIBO Matrix Dual 24x4 3pin brkout
40-595A-009
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
product
Sensor Imitator Probe
The Sensor Imitator Probe is mainly used for the simulation of the signals generated by different types of sensors in the vehicle. It can be used in all automobiles (12V/24V), to distinguish faults that lie in the sensor itself or are related to the connectors or wires.
-
product
Electric Shock Protection Analysis
60364-4-41 StandardBS 7671 StandardEN 50122 StandardTN-C, TN-S, TN-C-S, TT & IT Earthing TypesElectric shock requirementsLoop impedance and current calculationTouch voltage calculation and evaluationCalculation considers resistance to ground / earthGround Fault Current Interrupter (GFCI) or Residual Current Circuit Breaker (RCCB) or Residual Current Detector (RCD) protectionReports in Crystal Reports and MS Excel
-
product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
The 40-205-008 (PXI) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
Fault Locator
SNOOPi
SNOOPi employs a bespoke optical sensor to detect and discriminate between fault and natural gas.
-
product
Cable & Antenna Analyzer
iVA Series
VSWR, Return Loss Measurement & Distance to Fault. The iVA Series Cable & Antenna Analyzer is an exciting new product from Kaelus that enables users to accurately measure VSWR/return loss and the location of the VSWR/return loss faults in their RF infrastructure. The wireless connectivity allows unprecedented measurement flexibility and opens up new & important possibilities in sweep testing and multi-port testing.
-
product
Cable Testers
The CableTool uses TDR (Time Domain Reflectometry) technology to quickly identify an open or a short from 0 to 2,500 feet within a foot of the fault.
-
product
Gigabit Ethernet Tester
GET-100
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
-
product
Radioactivity
Higher than the natural ambient/background radiation, it originates from building materials or is inhomogeneous at geological faults and underground watercourses. It causes cell damage (tumors), cell death, etc. Radioactivity (=ionizing radiation) is measured in sieverts per hour (Sv/h) or simply as a count rate (pulses/second [Ips] or pulses/minute [Ipm]).
-
product
Partial Discharge Simulation Devices
Hangzhou Xihu Electronic Institute
Simulation device of cable PD faults, simulation device of switchgear PD faults, simulation device of GIS PD faults, simulation device of transformer PD faults.
-
product
Fault Passage Indicator for Overhead Lines
Sensorform OFI-FLS
The Sensorform OFI-FLS is a Fault Passage Indicator for Overhead Lines, which is designed to assist in the rapidlocation and isolation of faults on Medium Voltage networks (1-38kV). When the current in the phase exceeds a preset level, the fault is indicated by means of both a mechanical flag indicator and high-intensity LED indicators.
-
product
FAult Detector and OScilloscope 9 Functions in 1
FADOS9F1
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
2 unique features are added to the FADOS9F1 over the FADOS71. First feature is the Programmable DC Power Supply; It can be adjusted between 0-16V and 20-1500mA with power output; the DC Voltage/Current graphs of the electronic card power supply can be produced. The second feature is the “IR Remote Temperature Measurement Sensor”; this sensor is used to find the components that heat up by drawing too much current. Using these two features together may reduce the time for trouble shooting some malfunctions by 5 to 10 times. These features can be used as a new technique for trouble shooting.
-
-
product
Compact Cable Test Van
ETL-8
Van-based cable test and fault location system ETL-8 is used for testing cable insulation and locating cable faults using a variety of methods.
-
product
PCI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Output, Bank-Isolated Digital I/O Device
778835-01
The PCI-6515 is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Battery Portable Passive Intermodulation Analyzer
iPA Series
The iPA Series Passive Intermodulation (PIM) analyzer is the first battery powered PIM Test Analyzer versatile enough to support multiple test scenarios such as testing at the top of the tower, base of tower, roof top and in-building for DAS systems. This IEC compliant 20W, rugged, battery operated design includes a tablet computer in a ruggedized case for remote control. This allows hands-free dynamic testing that is safe and convenient. Add the optional Range to Fault (RTF) module to quickly identify the location of PIM and Return Loss sources.
-
product
Low Power DC/DC Converters
The 4:1 Input Voltage 75 Watt WDE includes remote sensing, ultra-wide output voltage trim, and remote ON/ OFF. The digital power management enables increased reliability, configurability, voltage / current precision and fault management.
-
product
OTDR
Wuhan Sunma Technology Co., Ltd.
OTDR, short for optical time-domain reflectometer, is an optoelectronic instrument used to characterize an optical fiber. It can offer you an overview of the whole system you test and can be used for estimating the fiber length and overall attenuation, including splice and mated-connector losses. It can also be used to locate faults, such as breaks, and to measure optical return loss.
-
product
Infrared Camera for Methane and VOC Detection
FLIR GF320
The FLIR GF320 detects hydrocarbon and volatile organic compound (VOC) emissions from natural gas production and use. With this optical gas imaging camera, inspectors can check thousands of components and see potential gas leaks in real-time. The GF320 is lightweight, offers both a viewfinder and LCD monitor, and has direct access to controls. Embedded GPS data helps in identifying the precise location of faults and leaks, for faster repairs.
-
product
1310nm Direct Modulated Fiber Optical Transmitter
ONT-8600AS
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai 1310nm direct modulation fiber optical transmitter, adopts high linearity DFB laser of famous brand in the world, and builds-in perfect pre-distortion adjustment circuit and laser APC, ATC closed loop control circuit. All the operating parameters of fiber optical transmitter are controlled by microprocessor, and the LCD screen on the front panel can display relative operating status and the fault information.
-
product
Handled Touch-Screen OTDR 1310/1550nm
TR200
Shenzhen Sharingtek Communication Co., LTD
Hand-held Optical Time Domain Reflectometer series is a newly hand-held and intelligent communication measuring device in accordance with the test of Optical fiber and Communication System. The product is used to measure the parameters like optical fibers, length of the optical fiber, loss, following quality and the like. It can quickly and accurately position the case point and fault point of the optical fiber link. It can be widely used in the engineering construction, route maintenance and urgent repair of the Optical fiber and Communication System. It can also be used in optical fiber and optical cable development as well as production measurement. The product can effectively do help to the installation and construction of the optical fiber network, the following speedy and effective maintenance and the troubleshooting test.OTDR is sturdy and durable with a novel and attractive appearance. The most succinct operation interface with a simple and intuitive style is specially designed for the domestic users. The dual operation mode of press key and touch screen effectively simplifies the application of the users. You can obtain the test result by the one-click analysis and the events will appear on the main interface in a list form with the information of event number, type, location (distance), loss, reflex, gradient of the events (attenuation) and total loss. Intelligent power management mode is employed to the machine. The working duration of the machine can be more than 10 hours with the high-capacity lithium battery.
-
product
Pole Mounted Detector of PtG and PtP faults in 6-69V Line
LineTroll 111K
The unit mounts 3-5m below the conductors and monitors all three phases. The indicator is powered by replaceable long-life lithium batteries which have a lifeexpectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
product
Professional Thermal Camera
FLIR T540
Diagnose potential faults in industrial, electrical, and mechanical systems, or discover temperature anomalies in R&D testing with the 464 × 348 resolution FLIR T540. This portable, ergonomic thermal camera offers advanced features like 1-Touch Level/Span and continuous laser-assisted autofocus, making it the perfect non-contact diagnostic tool for condition monitoring and research applications. Streamline electrical/mechanical surveys, troubleshooting, and repairs with Inspection Route mode, which runs pre-planned routes created in FLIR Thermal Studio Pro (Route Creator plugin required) so users can record temperature data and imagery in a logical sequence. The built-in Macro Mode allows R&D users to quickly switch from wide angle to close-up analysis without changing the lens. When coupled with Research Studio software, the T540 helps engineers assess unexpected hot spots and find potential design flaws. The T540 also features FLIR Ignite for automatic uploading of images directly from the camera to the cloud for easy, secure storage and sharing. The purchase of a T540 camera includes a 3-month subscription to FLIR Thermal Studio Pro and FLIR Route Creator.
