Fault
-
Product
Audio Frequency Generator
TM530
-
TM530 Audio Frequency Generator is provided with Pinpoint Fault Locator for pinpointing the low resistance fault and detecting cable route. When detecting, TM530 will inject a signal current of 1kHz audio frequency into the cable, and accordingly a magnetic wave of the corresponding frequency will be generated on the cable. Pinpoint Fault Locator will collect this magnetic signal, thus obtains the information of the cable fault and the route.
-
Product
4 Digit Angle Position Indicator (API)
TA-900
-
This has been the New standard in Angle Position Indicators. 4 digit API has fault monitoring for both low-level and loss of signal (LOS) and this status is shown on the front panel led. The unit provides simultaneous connection of both synchro and resolver devices.
-
Product
PXI BRIC8 FIBO Matrix Dual 93x4 2pin brkout
40-592A-113
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Datacom Analyzers
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber provide E1/2M Transmission Analyzer is one multi-functional and full- featured digital transmission system test device, designed for the installation test, engineering check and acceptance, daily maintenance of digital networks, mainly performing channel test, alarm analysis, fault finding and signal analysis. In addition, this instrument further provides various protocol converters with one-way and bi-directional bit error test function. These capabilities make it ideal for field use.
-
Product
DC Safety Inspection Device For Solar Panels
“DC Fault Tester”
-
Identifies defect position instantly- contributes to saving inspection time
-
Product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
Fault Insertion Unit
The 40-205-008 (PXI) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
PXI BRIC8 FIBO Matrix Dual 6x2 3pin brkout
40-595A-001
Matrix Switch Module
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
Interface Board for Gigabit Ethernet
40-965-910
Interface
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
Product
Failure Analysis
-
Failure analysis on electronic components is a continuous challenging task. The smaller transistor dimensions, increasing functional complexity and changing device packaging styles requires new tools and skills for sample preparation, fault localization techniques, high resolution imaging and analysis.
-
Product
Ground Earth Resistance Tester
2678X
-
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
Product
Short Circuit Locator for Power Cables
A910
-
The A910 is a short circuit locator designed for fault location in power cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A910 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 5mohm (approximately 90 m of 300 sqmm cable) and less than 30 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.
-
Product
High Voltage EMC Surge Generator
TM510
-
TM510 Surge Generator is mainly used for testing power cable high-resistance and arc-over fault whose grade range is 0-10kV, co-operating with cable fault tester and locating devices to test and locate faults. If the user choose the professional digital milli-ampere-meter, as for cable with grade range about 0- 6kV, the instrument can also be used to do DC&voltage resistance test and current leakage test after the fault is repaired. The instrument is internally equipped with voltage-rise rectifying and discharging device, has complete functions, and is also convenient and safe to be wired and operated.
-
Product
Cable Tester & Cable Tracer & Multi-Functions Lan Tester
M-CT-430A
-
Fuzhou Metricu Technology Co Ltd
The multifunction LAN tester M-CT-430A is designed for maintenance and installation of cable, cable tracer, and HD Coaxial video level meter test in one equipment. The unit supports detect the near-end, mid-end and far-end fault point of RJ45 cable connector, and also supports Port Flash, PING test, IP address Scan, Link Monitor. Installers take the all in one cable tester, making working conditions safer and increasing productivity.
-
Product
Plug-In Power Supplies
-
VECTOR Electronics and Technology, Inc.
Standard PCI output Voltages : 5.0V, 3.3V, +12.0V, -12.0VHot swap, N+1 redundancy with internal OR-ing diodes.99 power factor corrected AC 90-264V input DC 36-72V (48V nom.), or DC 18-32V (24V nom.) Current sharing on 5.0V and 3.3V outputs Power & Fault LED indicators to faceplate Excellent performance
-
Product
Electronics Failure Analysis System
Sentris
-
Due to the continued decrease in integrated circuit feature size and supply voltages, detecting and locating the miniscule amount of heat generated by failure sites has become increasingly difficult. Sentris pinpoints low-level infrared thermal emissions from IC faults such as short circuits and leakage current.
-
Product
FTL Test Block
-
FTL testblock with dust cover and current disconnect pinThe FTL is a test block for interfacing substation devices (protection relays, fault recorders, revenue meters, ... ) to the voltage and current transformers and to other equipment on the system side of a power grid. The FTL test block uses disconnect pins to isolate the substation devices from the system side equipment. Once isolated, secondary injection can be performed using banana jacks on the front side of the test block.
-
Product
Visual Fault Locators
MVFL Series
-
Shanghai Tarluz Telecom Tech Co., LTD
MVFL series Visual Fault Locators is meet the Class IIIA product, which is the easiest way to identify fibers from end to end and locate polished connector endfaces. Its red laser shines through most yellow-jacketed fibers to help you pinpoint breaks, bends, faulty connectors, splices and other causes of signal loss. The 1mW output power enable the MVFL has a reach of up to 5 km. MVFL seires VFL locates faults visually by creating a bright red glow at the exact location of the fault on single mode (SM) or multimode (MM) fibers. Due to its small size, lightweight and simple but proven design, the MVFL can accompany you anywhere In your pocket or belt pouch in harsh environment
-
Product
LASAR Post Processor, Run Time And Diagnostic Test Solution
DtifEasy Series
-
DtifEasy is a full-featured tool set for importing, converting, and executing IEEE-1445 compliant digital test vectors generated by a LASAR simulation. All four IEEE-1445 file types - UUT model group, Stimulus and Response group, Fault Dictionary group, and Probe group are supported by DtifEasy; providing the user with the ability to execute go/no-go, fault dictionary, and guided probe sequences. DtifEasy supports MTS' 3U PXI GX529x series of dynamic digital instrumentation to 200 MHZ as well as the 6U PXI GX5960, 50 MHz digital instrumentation. All of these instrument families are compatible with the digital logic probe.
-
Product
Automatic Relay Tester
-
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuits correctly. It is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay testers.
-
Product
Detection of Earth Faults (PtG) and Short Circuit (PtP) Faults
CableTroll 2330
-
CableTroll 2330 is an indicator for detection of earth faults (PtG) and short circuit (PtP) faults on multi and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
In-Circuit Test Fixtures
-
In-circuit testing provides electronic manufacturers a reliable, high fault coverage verification method for the assembly process. Circuit Check ICT fixtures are robust, reliable and designed for easy customization to cover a large range of PCB sizes without impacting turnaround time. We stock a large variety of fixture sizes and actuation methods to meet your test demands. If a stocked sized ICT fixture is not adequate our engineering staff will design a custom solution.
-
Product
OTDR Tester
M-OTDR-502
-
Fuzhou Metricu Technology Co Ltd
Optical Time Domain Reflectometer Wavelength 1310 / 1550nm, max test range 150KM, Dynamic range 28 / 26dB, SOR standard data saving, create PDF/EXCEL format report, stable laser source, support CW/270/330/1000/2000Hz, Test fiber's length, loss, attenuation parameters and event map, locate connection point/fusion point, Automatic analysis of various linkers/fusion points, easy analyze of various events,Support saving curves number ≥30000pcs, loss test, detect the optical or optical components loss value, etc. Test IP camera, optical power meter, visual fault locator, RJ45 cable TDR test, cable tester, cable tracer, etc.






















