Charge Sensitive Preamplifiers
See Also: Detectors
-
Product
Low-Noise Voltage Preamplifier
SR560
-
Stanford Research Systems, Inc.
The SR560 is a high-performance, low-noise preamplifier that is ideal for a wide variety of applications including low-temperature measurements, optical detection, and audio engineering
-
Product
Time Sensitive Networking Evaluation-Kit
-
The evaluation kit offers developers the possibility to test and evaluate Ethernet TSN for their own applications. It consists of either a Smartzync board (Xilinx) or a Netleap board (Intel/Altera) with an optionally implemented IPMS TSN-IP core for endpoint applications (TSN-EP), switched endpoint applications (TSN-SE) or switch applications (TSN- SW). Linux drivers with application examples, as well as RTOS test applications and TSN network configuration examples are also available.
-
Product
Preamplifiers
-
A.H. Systems'' Preamplifier line is an excellent choice with a rugged design, no hassles with soldering your own power leads and they improve overall system sensitivity by at least 20 dB. All of A.H. Systems'' Preamplifiers come with a 12-volt (or 15-volt) DC regulated power source. A low voltage indicator confidently allows you to power the amplifier with your own external 12-volt DC battery. This makes it a convenient choice for field measurements. See table below for amplifier specifications.
-
Product
Lock-In Voltage Preamplifier
SR550
-
Stanford Research Systems, Inc.
The SR550 Voltage Preamplifier is designed to work with any SRS lock-in amplifier. Preamplifiers provide gain close to the experimental detector, before the signal-to-noise ratio is permanently degraded by cable capacitance and pickup
-
Product
Collapsible 6 Inch Charge Plate Monitor Assembly
CPM-760A
-
- 6" x 6" (15 cm x 15 cm) conductive plate- Total system capacitance of 20 pF ± 2 pF- Meets the requirements of ANSI/ESD STM3.1 and ANSI/ESD SP3.3- Designed to perform audits on overhead ionizers and room ionization systems- Flexible to also evaluate and balance bench top ionizers- Completely collapsible for compact storage- Designed to be used with the PFM-711A and PFM-711B
-
Product
High Sensitivity Reed Relays
Series 86
-
General purpose relays - As series 80 and 88 but with coil resistances typically twice as high
-
Product
Crossed-Roller Bearing Linear Stage 25mm Travel,Sensitivity 2um
KSM25(A)-65
-
Model：KSM25(A)-65 Crossed-Roller Bearing Linear Stage 25mm Travel,Sensitivity 2um Details&Spec: Please refer to KSM25(A)-65 Specification,It is combinated by 2pcs KSM25(A)-65 (C,SR,SL).
-
Product
Vibration Sensitivity Tester
Vibratron II
-
The Vibratron II provides a non-invasive means of measuring the sensitivity to vibration of large nerve fibers of a patient's fingers and toes. Reliable quantitative measurements are achieved with a test that takes only minutes to administer. A two-alternative forced choice procedure is used to determine the degree of sensitivity for comparison to normals.
-
Product
Highly Sensitive Silica Monitor
SLIA-300
-
Highly sensitive silica monitor for ultrapure water management in semiconductor/FPD processes
-
Product
Microphone Preamplifier
426A05
-
Preamplifier for 1/4" side vented prepolarized microphones.
-
Product
Charge Coupled Device (CCD) Standard Image Sensors
-
Teledyne e2v is the leading supplier of scientific grade Charge Coupled Device (CCD) image sensors for the most challenging low light imaging and spectroscopy applications.
-
Product
Portable Charging Facility Testing Platform For Electrical Vehicle
-
PONOVO has long-term follow-up technology in China and abroad. Based on its own mature intelligent power detection equipment, and according to its own advantages in the field of new energy, PONOVO could be able to provide users with professional new energy test system solutions.
-
Product
HDCD Battery Charge Tester
-
HD Power Test Equipment Co.ltd
HDCD Battery Charge Tester is mainly used for the charge test of the lead-acid battery of the backup power supply in the telecommunications, mobile, substation, railway transportation and pertrochemical industry power DC industries. It keeps the constant communication maintain between the battery charge ensuring a perfect charge.Battery charge tester is designed using intelligent three-stage charging mode to achieve the function of automatic conservation between charging and floating charge. It also can on-line detect the voltage of the whole battery, real-time display and record the voltage of whole battery. The tester can automatically accomplish charging after setting the parameter of voltage, current, time and capacity.
-
Product
Current Preamplifier
1212
-
The Model 1212 Current Preamplifier is designed as a low cost, gerenal purpose, benchtop instrument to provide a high performance detection system for small ac and dc currents. The 1212 operates with a virtual ground at its input which mitigates unpredictable high frequency rolloff due to input cables and stray capacitance.
-
Product
UFP series High Sensitivity Fiber Optic Alignment Stages
UFP
-
Model: UFP1A-LFeatures:• The linear stage has both coarse adjustment and fine adjustment, sensitivity is much better than 0.5um• The rotation stage sensitivity is much better than 23.4" • High stability
-
Product
Preamplifiers
-
The primary function of a preamplifier is to extract the signal from the detector without significantly degrading the intrinsic signal-to noise ratio. Three basic types of preamplifiers are available: the current-sensitive preamplifier, the parasitic-capacitance preamplifier, and the charge-sensitive preamplifier. ORTEC manufactures a preamplifier to fit your detector, your application, and your budget.
-
Product
Charge Coupled Device (CCD) Image Sensors for Space and Ground-Based Astronomy
-
(CCDs) for Space science, Ground-based Astronomy, and Earth observation applications with an impressive record of successful deliveries to a wide range of customers over 40 years.All Teledyne e2v devices can be supplied partially or fully customised to fit the application and achieve the best possible system performance. CCD image sensor design, manufacture, test and characterisation are carried out in-house enabling control from start to finish. Multi-polysilicon, multi-metal and back-illumination options are available for high resolution, high sensitivity and very low noise.
-
Product
EV Charging Station Tester
EV : ChargeCheck
-
The EV Industry’s Charging Station Tester of Choice. • Simulates an electric vehicle • Tests J1772 (type 1) tethered leads • Tests IEC62196 (type 2) sockets • Tests IEC61851-1 mode 3 communication compliance • Tests for correct polarity • Tests for earthing presence • Tests contactor actions.
-
Product
Active Input Module for Teledyne RESON TC4014 and TC4032, Hydrophones with Built-In Preamplifiers
EC6076
-
The EC6076 Active Input module is for the Teledyne RESON TC4014 and TC4032 hydrophones with built-in pre-amplifiers.EC6076 provides an easy interface to the hydrophones, it al-lows use of the differential output from the hydrophones ei-ther via direct feedthrough of the signal on an XLR output con-nector or via the built-in differential amplifier that converts the differential hydrophone signal into a single-ended +6dB signal on a BNC/coax out. EC6076 has a built-in rechargeable battery that provides power for the EC6076 differential amplifier and the TC4000 hydrophone.
-
Product
DC/DC with UPS and Charge Controller
-
A wide input range, quad output PC/104-Plus DC/DC converter with a built-in battery charger and uninterruptable power supply (UPS) controller. Designed for harsh environments, the power supply operates from -40 to +85C without a fan or heatsink making it ideal for industrial applications.
-
Product
Preamplifier
-
Is designed for the amplification of measuring signals, e.g. weak signals of near field probes with high resolution.
-
Product
Ball Bearing Linear Stage,13mm Travel, Sensitivity 3um
PSM13(A)-34
-
Model：PSM13(A)-34 Ball Bearing Linear Stage,13mm Travel, Sensitivity 3um
-
Product
12V Auto Battery And Charging System Analyzer
1947
-
Peaceful Thriving Enterprise Co Ltd
1. Check for batteries, regulators and alternators. 2. For all 12V system vehicles, with LED indicator that helps pinpoint problems for fast troubleshooting. 3. Other car battery testers are also available.4. With CE Approval.
-
Product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
-
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
-
Product
Surface Charge and Zeta Potential
-
Surface analysis is a vital method for qualifying new materials in technical and biological applications. Surface charge analysis empowers users to closely monitor the surface chemistry from small particles in the nanometer range up to large wafers. Gain insights into modifications resulting from surface treatment and surface interactions with natural environments under near-ambient conditions. Get a competitive edge in optimizing existing products and developing new ones using the Anton Paar instruments which offer zeta potential measurement for a wide range of applications.
-
Product
High Sensitivity Reed Relays
Series 87
-
General purpose relays - sensitive versions of series 85 and 89
-
Product
Charge Meter
NK-1001A/NK-1002A
-
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
-
Product
Externally Polarized Precision Condenser Microphones & Preamplifiers
-
Externally polarized microphones set the initial standard for all acoustic test and measurement applications. They rely on a dedicated 200V power supply and specialized cables with 7-pin LEMO® connectors. Their straightforward design supports a wide product range. Often chosen as replacements for existing models or when prepolarized alternatives are unavailable.
-
Product
Charge Converter
CH-6130/6140
-
The CH-6130/6140 charge converter is a simplified type of charge amplifier converting charge signal to voltage.It can be connected directly to an input BNC connector of a CCLD applicable equipment such as FFT analyzer or vibration comparator, enabling direct connection of a charge output pickup without suing a box type amplifier.
-
Product
350 MHz Preamplifier
SIM914
-
Stanford Research Systems, Inc.
The SIM914 350 MHz Preamplifier contains two wide-bandwidth, DC-coupled amplifiers, each with a gain of 5 (14 dB). Its fast rise time, low noise and excellent DC accuracy make it an ideal instrument for amplifying signals like those from photomultiplier tubes and photodiodes.
