Charge Sensitive Preamplifiers
See Also: Detectors
-
Product
Charge Plate Monitors
-
Our easy-to-use charge plate monitors allow you to accurately evaluate air ionization systems used to neutralize static charge accumulation. Benefit from our economical solutions and products that offer onboard data storage to automate ionization system testing.
-
Product
Time Sensitive Networking Evaluation-Kit
-
The evaluation kit offers developers the possibility to test and evaluate Ethernet TSN for their own applications. It consists of either a Smartzync board (Xilinx) or a Netleap board (Intel/Altera) with an optionally implemented IPMS TSN-IP core for endpoint applications (TSN-EP), switched endpoint applications (TSN-SE) or switch applications (TSN- SW). Linux drivers with application examples, as well as RTOS test applications and TSN network configuration examples are also available.
-
Product
Current Preamplifier
1211
-
The model 1211 Current Preamplifier was designed to provide all of the features required of a modern laboratory preamplifier. It measures cur rents with full scale sensitivity ranging from 10 to 10 amperes.
-
Product
High Temperature Charge Mode Accelerometers
-
Charge mode output accelerometers from PCB® use piezo-ceramic sensing elements that output an electrostatic charge signal proportional to the applied acceleration. These sensors can operate at extremely high temperatures because they do not contain the built-in signal conditioning electronics that limit the temperature range of ICP® accelerometers. Charge mode sensors are used in the testing of gas and steam turbines, jet engines, high power motors, exhaust systems and automobile engines where temperatures can range from 500° F (260° C) to 1200° F (649° C).
-
Product
Time Sensitive Test Tools
-
We have developed a series of custom testing tools as part of our dedication to performing the most comprehensive testing in the industry. These tools allow for testing at lower layers than most commercially available tools and are available for use in your own testing labs. In addition, we have an extensive amount of T&M partner test tools which members of our testing services also have access to.
-
Product
DC to 350 MHz Preamplifier
SR240A
-
Stanford Research Systems, Inc.
The model SR240A 350 MHz Preamplifier is a 4-channel, DC-coupled instrument with a gain of 5 per channel. The amplifiers can be used independently or cascaded to provide gains of 5, 25, 125 or 625.
-
Product
High Sensitivity Reed Relays
Series 86
-
General purpose relays - As series 80 and 88 but with coil resistances typically twice as high
-
Product
Explosion-Proof Differential Pressure Switch, 10 inH2O Sensitivity
H3
-
Explosion-proof, heavy duty, industrial unit has patented and unique new design which provides sensitivity to differential pressures as low as 10 inches of water (254 mm w.c.), yet handles total pressure of 1500 psi (103 bar). Unlike common differential pressure switches that use a piston-type motion transfer, the Series H3 utilizes a rotary motion transfer shaft that prevents a change in total pressure from causing a setpoint shift.
-
Product
Programmable Current Preamplifier
99539
-
The Model 99539 is a modular, multi-channel current preamplifier with parallel, logic level, gain control input. It consists of circuit boards which plug into a 3 1/2" high by 19" wide rack chassis.
-
Product
Battery Discharge and Charge Tester
-
HD Power Test Equipment Co.ltd
Battery Discharge Charge Tester is mainly used for the charge test of the lead-acid battery of the backup power supply in the telecommunications, mobile, substation, railway transportation and pertrochemical industry power DC industries. It can proceed the discharge and charge for the batteries to extend the lift-time.
-
Product
Smart Refrigerant Charging Kit
HUB4
-
UEi Test & Measurement Instruments
The HUB4 gives the ability to wirelessly get Vapor and Liquid pressures via the WPP1 probes and Vapor and Liquid temperatures via the WPC1 probes, all via the free UEi Hub App. Easy to use and a rugged design make the App and probes an excellent addition to any technician's toolbox.
-
Product
Highly Sensitive, Lightweight Backpack Radiation Detector (BRD)
identiFINDER® R700
-
The identiFINDER R700 Backpack Radiation Detector (BRD) offers new spectroscopic broad-search capabilities. Once dismounted, the identiFINDER R700 provides the capabilities required to successfully perform wide-area searches quickly and efficiently while offering exceptional sensitivity, communication, and trusted spectroscopic algorithms in a lightweight, ergonomic form-factor.
-
Product
Highly Sensitive Silica Monitor
SLIA-300
-
Highly sensitive silica monitor for ultrapure water management in semiconductor/FPD processes
-
Product
Acoustic Emission Preamplifier
-
The Acoustic Emission Preamplifier is a instrument designed specifically for use with acoustic emission sensors, which is used to boost the signals and filter out any noise or interference. With its advanced technical features and robust design, the QingCheng Acoustic Emission Preamplifier is the perfect choice for professionals seeking a high-performance acoustic testing solution.
-
Product
High-Sensitivity Tri-Axial Accelerometer with Built-In Preamplifier
NP-7310
-
NP-7310 is the accelerometer with built-in preamplifier, and capable of tri–axial directions simultaneous measurement. It is suitable for the low frequency vibration measurement such as ground vibration or floor vibration while operating the machine. NP-7310 can be used with the sensor amplifier unit such as AU-2100, AU-2300 or PS-1300. Also, it is possible to input directly to the analyzer or recorder which the constant current amplifier is built-in such as the FFT Analyzer of DS-2000 series, DS-3000 series, CF-7200A, CF-9000 series or CF-3650/3850 series.
-
Product
Pyrgeometer Low Temperature dependence of sensitivity
CGR 4
-
CGR 4 pyrgeometer is an instrument for the highest quality scientific measurements. The specially designed meniscus dome provides a 180 field of view with negligible directional response error. A hard-carbon coating on the outside of the dome smoothes the spectral response and provides extra protection to the silicon surface.
-
Product
Preamplifier
-
Is designed for the amplification of measuring signals, e.g. weak signals of near field probes with high resolution.
-
Product
High Sensitivity Accelerometers
-
Metra Meß- und Frequenztechnik Radebeul GmbH & Co. KG
The piezoelectric accelerometers on this page are intended for the measurement of lowest vibrations. Their high sensitivity is achieved -unlike other high sensitivity accelerometers- by the sensing element itself and not by internal amplification. From this results highest resolution and lowest noise.
-
Product
Charge Plate Monitor
-
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the charging plate (detector), which has almost the same capacitance as the device's ground capacitance , with high accuracy, and is the most suitable measuring instrument for checking the effect when installing the ionizer and for daily management.
-
Product
Saluki SE4002 FET Input Preamplifier
-
The SE4002 is a low-noise, ultra-high input impedance preamplifier with excellent common-mode rejection. It is designed to work with any Saluki digital lock-in amplifier. The preamplifier minimizes noise and pickup in the connecting lines and reduces measurement time in noise-limited experiments.
-
Product
High Current capacity testing from Intelligent Charging
CT75A
-
A UK-based helicopter manufacturer wanted high capacity testing capability for their helicopter batteries and came to Intelligent Charging for a Special Unit. As a result of the above requirement, Intelligent Charging designed and built this new capacity testing unit to add to our extensive range of intelligent battery charging and capacity testing products. With up to 100.0A capacity testing capability this model will satisfy the most demanding aviation battery.
-
-
Product
Thermal Sensitive Parameter Selector
UI9600
-
Parameter measured under normal temperature:1) β (0-99)2) Switching time T (0.01μs-99.9μs), including Tr, Ts, Tf3) VCES (0-2V), VBE (0-2V)4) Leakage current ICEO (0.01μA-99.9mA)5) Withstand voltage BVCEO (50V-650V)• Parameter measured under high temperature: VBE, β, ICEO
-
Product
EV Charging Station
Residentual
-
BENEFITS OF RESIDENTIAL CHARGING: *Charge up to 7x faster than the Level 1 cordset that came with your electric vehicle. *Level 2 (240V) charging stations are more affordable than ever – starting at just $379! *Tax incentives and rebates offset purchase and installation costs, up to 100% in some areas *It’s more convenient to charge at home than using a public station. *Indoor/Outdoor rated (fully sealed NEMA 4 enclosures) *The Level 1 cordset that came with your electric vehicle can be used as a portable charging station or for a second charging station when you have company with an EV.
-
Product
Crossed-Roller Bearing Linear Stage ,25mm Travel,Sensitivity 1um
NFP-1462
-
Model:NFP-1462 Crossed-Roller Bearing Linear Stage ,25mm Travel,Sensitivity 1um
-
Product
Auto Charging System Analyzer
TE6-0606
-
Hangzhou Tonny Electric & Tools Co., Ltd.
This unit simply plugs into your car's cigarette lighter socket and will present you with alternator and battery status. On the left side is the alternator status indicating if it's charging the battery at too high a voltage, normal or too low. On the right is the battery status green LED charged 12.4-12.6V, yellow LED recharge 11.8-12.35V, and red LED dead<11.75V indicators.
-
Product
Capacitor Charging Power Supplies
-
Lumina Power CCPF and CCHP capacitor chargers utilize the latest innovations in power electronics to deliver clean and efficient energy for pulsed power applications. Learn more about the CCPF and CCHP below.
-
Product
EV& Charging Pile Test Set
DC Testing
-
With the development of Electric Vehicles in the world, more and more charging piles have been installed in different places. Due to the different understanding of the standards among EV manufacturers and charging piles suppliers, there may be hidden danger during the charging process.
-
Product
Charge Amplifiers & Signal Conditioning
-
The use of charge amplifiers alongside piezoelectric charge output sensors is still widespread in many industries. This is due to the rugged and high temperature capabilities of the sensors. There are many challenges in using these sensors and it needs a good understanding of the technology to get a quality, noise free signal for accurate data.
-
Product
Programmable USB Hub with 4 Charge Ports
-
The USBHub2x4 is a programmable USB 2.0 compatible hub featuring 4 device downstream ports with standard USB type-A receptacles and each port is capable of delivering up to 2.5A simultaneously. With two host (upstream) connections using usb mini-B connectors, the USBHub2x4 is perfect for environments where multiple devices need to be shared or switched between two host computers. E.g.: software regression testing, iPhone software development and validation, Android software development and validation, USB device regression testing, manufacturing testing, device burn-in testing and USB device charge-curve testing.
