Response
-
Product
Iris
-
Marshall Day Acoustics Pty Ltd
3D acoustic impulse response - measurement and visualisation. IRIS is a powerful and user friendly measurement system for capturing and analysing room impulse responses in 3D.
-
Product
Seismometers
3T-120 Pothole
-
120 s to 50 Hz frequency response (option to 100 Hz), 1500 V/ms-1 (2 x 750 V/ms-1) sensitivity, Covers the complete seismic spectrum with a single transfer function, Measured Self noise below the USGS NLNM from 166 s (0.006 Hz), remaining below the high frequency limit of the NLNM at 10 Hz, High linearity: >111 dB (USGS figures), Dynamic range of 167 dB at 1 Hz (Full octave width across 1 Hz), Cross axis rejection over 65 dB; sensor axes orthogonal to within ±0.05°, Remote, automatic electronic mass locking, unlocking and centring, Operating tilt range of ±5° with adjustable feet for off-horizontal installation bases, Low power consumption: 0.75 W from a 10–36 V supply, Stainless steel enclosure, 100 bar / 10 MPa waterproof connector, IP68 - protection against effects of permanent immersion under pressure to 350 m depth
-
Product
Precision Measurement System
OmniMic V2
-
Updated software and improved hardwareCompact, portable, accurate, affordableIntuitive software—open the box, start testing in minutesPerfect for setting up home theater systemsOptimized for use with netbooks and laptopsAccurate response down to 5 Hz, fully calibrated, includes FRD fileFor professionals and hobbyists—design and tune speaker systems and arrays
-
Product
Digital Psophometer
Model 1072
-
Aplab Psophometer is a portable unit designed for the use of testing telecommunication equipment. It has Psophometric filter, which has the frequency response of the weighing network based on the CCITT recommendations and frequency response characteristics for unweighted measurements. The additional features included in this model are, ‘Recorder out’ available at the rear panel for plotting a response curve, built-in stable calibration signal for calibration check and Lo Battery facility to check the Battery condition.
-
Product
Temperature Measurement IR Sensors & Detectors
ST150 With Diffractive Lens
-
A single-channel silicon-based thermopile with integrated diffractive lens and internal baffle that delivers a very low Temperature Coefficient of Responsivity of -0.04%/C with a high output voltage, 19.5 FOV and a quick time constant of 38ms. This Low-cost detector comes in a TO-5 package and has a very short thermal shock response to ambient temperature change.
-
Product
CXA Signal Analyzer, Multi-touch, 9 kHz to 26.5 GHz
N9000B
-
Master the essentials in signal characterization with the leading low-cost tool in signal analysis Perform cost-effective stimulus response measurements with the optional built-in tracking generator Add crucial functionality with X-Series measurement applications Enhance theory with practical skills when used with a training kit in your RF & microwave education lab
-
Product
Combinated Thermal Imaging Cameras
-
PeakTech Prüf- und Messtechnik GmbH
This new combination of the latest True RMS graphic multimeter and responsive thermal imaging camera enables professional use in all areas of electrical engineering. The multimeter has many various functions to carry out precise measurements, which you can log automatically, save with a screenshot or record and process using an app for Android or iOS mobile devices.
-
Product
SPM Monitor
CS-150
-
The CS-150 is a high-precision chemical concentration monitor designed for use with the SPM solutions used in semiconductor-manufacturing cleaning processes. Featuring fast response and a compact size, the CS-150 continually monitors the concentrations of the various components of the SPM solutions (H2SO4/H2O2/H2O) used to remove metal ions and organic substances. Feedback control based on the monitor output is used to keep the concentrations of the SPM solutions within the allowable ranges and to eliminate unnecessary replacement of chemicals.A short measuring cycle allows the accurate tracking of chemical concentrations, while the compact design facilitates integration with a cleaning device.
-
Product
Microphone Preamplifier
426E01
-
Nominal Microphone Diameter: 1/2 Gain -0.05 dBFrequency Response (0.1 dB) (re 1 kHz)6.3 to 125000 HzFrequency Response (-3 dB) (re1 kHz) Phase Linearity (<1 )32 to 20000 Electrical Noise (A-weight)<2.8 V<2.8 V[1] Output Slew Rate 2 V/S[2]
-
Product
Spiral Antenna
-
UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain.
-
Product
Small Diameter Tubes Optical Bubble Sensor
BE-A
-
Panasonic Industrial Devices Sales Company of America
*One-touch Attachment*For Small Diameter Tubes*High Speed Response Time*Ultra Compact*For A Wide Range Of Power Supply Voltages*Built-In Amplifier*Allows For Close Proximity Attachment*CE Approved*CE: EMC Directive
-
Product
High-Speed/LED Sensing Fiber Sensor
FX2
-
Panasonic Industrial Devices Sales Company of America
The FX2 Series Fiber Sensor has multiple amplifiers. The FX-A3R has a 15us high speed response time and is suitable for detecting small objects or objects traveling at high speed. The FX2-A3R-LED is an LED sensing type amplifier, which can detect weak lighting from LEDs.
-
Product
Aerospace and Defense Software for the 4000 X-Series
D4000AERB
-
MIL-STD 1553 and ARINC 429 trigger and decode for the InfiniiVision 4000 X-Series oscilloscopes, along with mask testing, frequency response analysis, and video analysis
-
Product
Attitude And Heading Reference Systems
AHRS
-
Beginning in 2001, Inertial Labs began manufacturing its MEMS-based, IP-67 sealed, MIL-STD-810G qualified, multiple interfaces and COM ports Attitude and Heading Reference System in response to the need for an inclusive and price competitive Antenna Pointing, Aiming, and Stabilizing applications. Each INS contains an Inertial Labs-developed tactical or industrial-grade inertial measurement unit (IMU) and an Inertial Labs-manufactured high-precision Fluxgate magnetometer.
-
Product
Frequency Response Analyzers
-
Venable Instruments has been focused on one goal: bringing the most versatile, full-featured frequency response analyzers to customers in industries where precise testing and measurement tools for power supply design is critical. Over 37 years of continual research and development has created the widest range of scalable frequency response analyzers to meet your company's current requirements, while providing a cost-effective growth path for increased testing functionality. Venable is a proven leader in aerospace, automotive, energy, defense, computer technology, academia, government research applications and virtually any industry requiring the highest standards in power supply and stability testing for repeatable and accurate results.
-
Product
Vector Network Analyzer
SNA5000A
-
The SIGLENT SNA5000A series of Vector Network Analyzers have a frequency range of 9 kHz to 8.5 GHz, with 2 and 4 port models available. Designed to give you instant insight into scattering, differential, and time-domain measurements. They are effective instrumentation for determining the Q-factor, bandwidth, and insertion loss filters and feature impedance conversion, movement of measurement plane, limit testing, ripple test, fixture simulation, and adapter removal/insertion adjustments. There are five sweep types: Linear-Frequency, Log-Frequency, Power-Sweep, CW-Time, and Segment-Sweep mode. The SNA5000A series VNAs also support scattering-parameter correction of SOLT, SOLR, TRL, Response, and Enhanced Response for increased flexibility in R&D and manufacturing applications.
-
Product
RS-422/RS-485 Repeater
ND-6510
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5022
-
The HMMC-5022 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5022 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gains response and excellent port matches over the 2-22 GHz frequency range.
-
Product
Broadband Sensors
-
Offers a response between 120 sec and 160 Hz in a smaller, rugged, low power and low cost system that is easy to install and deploy. Built with ease of installation in mind, it does not require mass lock, mass centering, and has a large operational tilt range which combines to reduce installation training, time, and cost.
-
Product
High Speed Digital Analog
-
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
Product
Telecomm Services
-
Advanced Technical Enterprises, Inc
The UNIVERGE SV8000 Series Communication Servers from NEC creates new ways of generating revenue and increasing customer responsiveness while simultaneously improving efficiency and reducing costs. This robust, feature-rich solution is completely scalable and can be expanded to meet your communications needs both now and in the future. Designed to be both versatile and scalable for your growing business needs, the SV8100 supports TDM, IP, video, wired or wireless.
-
Product
Continuous Gas Analyzer
CT5400
-
Multi-component continuous gas analyzer combines QCL and TDL technologies in a single rack mount enclosure to measure process gas and monitor emissions from sub ppm to % levels. The CT5400 is ideal for measuring NOx, SO2, CO, CO2, CH 4, NH3, O2, HCl and other combustion gases identified as pollutants, ozone depleting, or responsible for global warming.
-
Product
Extreme Low Power Detector Laser Power Meters
11XLP12
-
11XLP12 extreme low power detector is best suitable for low power im both the µW and mW regimes with very low thermal drift. Featuring broadband flat spectral response, minimal thermal drift and a noise equivalent power as low as 1 µW the 11XLP12 is ideally suited for measuring any pulsed or CW low power laser.
-
Product
Near IR Image Plates
-
The IR Display Plate is a versatile instrument that presents clear, high contrast images of all near IR laser beams. These displays are made on infrared sensitive phosphors which offer a variety of unique features, variable image retention times for pulsed lasers, high resolution for CW YAG, and a good response to gallium arsenide light-emitting diodes. All near IR lasers are capable of being displayed over a wide sensitivity range.
-
Product
Mobile Comm DC Source w/ Battery Emulation, DVM
66321D
-
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321D mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321D mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads. The 66321D dc source provides all of the capabilities of the 66321B with the addition of a built-in digital voltmeter.
-
Product
Manufacturing
-
Aerodyn's advanced manufacturing services provide high quality machining, fabrication, welding, and inspection services for all industries. We pride ourselves on being responsive and innovative, while maintaining the highest quality craftsmanship available.
-
Product
Compact Low-Frequency Control Element
900-LFC
-
The 900-LFC Low-Frequency Control Element extends the response of mid-sized P.A. systems to 35 Hz, revealing the nuances of your mix, down to the deepest bass with total accuracy.
-
Product
Surveillance Monitor
SMARTS II
-
*Real time frequency response evaluation*Audible and visible alarms*Remote monitoring*User settable alarm thresholds
-
Product
LXI 24-Channel 1GHz Video Multiplexer
60-721A-001
-
This High Performance Video MUX is designed for the switching of RF signals in 75Ω systems at frequencies up to 1GHz. It is ideal for 75Ω monitoring applications that require a multiplexer to select one channel to be routed to measuring equipment. The automatic connection of unused channels into 75Ω terminations helps maintain signal integrity and minimizes the possibility of introducing unwanted responses. The common connection is also automatically terminated into 75 Ohm when unused. Front panel LED indicators adjacent to each multiplexer input connector provide an easy visual identification of the active channel.
-
Product
COM Express Basic Size Type 6 Module with 11th Gen Intel® Core™, Intel® Xeon® and Intel® Celeron® Processors
Express-TL
-
ADLINK’s Express-TL COM Express Type 6 Basic size module is based on the 11th Gen Intel® Core™, Xeon® W and Celeron® 6000 processor, and is the first COM Express module to support PCI Express x16 Gen4, effectively doubling the bandwidth of previous generation COM Express modules. With a combined 8 cores, 16 threads, and up to 128GB memory, the Express-TL brings uncompromised system performance and responsiveness to your solution. Featuring brand new Gen 12 Intel® UHD Graphics and Intel® AVX-512 Vector Neural Network Instructions (VNNI), the Express-TL provides AI inferencing performance as much as 3X higher compared to previous generation non-VNNI platforms. The integrated Gen 12 Intel® UHD Graphics core can be configured to support one 8K independent display or four 4K independent displays (HDMI/DP/eDP). In addition, legacy display interfaces such as LVDS and analog VGA are still supported as build options. Key features for today’s applications are support for 2.5 GbE and USB 3.2 with transfer rates of up to 10Gb/s that can transfer image data from cameras faster than previous generation products. Combined with 8 processor cores at 25W TDP, Intel® AVX-512 VNNI, Intel® OpenVINO™ toolkit and Intel® UHD Graphics, the Express-TL is well suited for AI at the edge applications (AIoT/IoT).
