Response
-
Product
XCITE 1200 Laboratory Series
-
The Xcite 1200 Series provides medium levels of force for testing vehicles such as trucks, locomotives, off road construction equipment and power generation equipment such as turbines and generator rotors, stators and bearings. The larger force capability is still coupled with a frequency response in the 500 Hz to 1000 Hz range for modal studies of highly damped and non-linear structures.
-
Product
DC Bench Power
XPH Series
-
AMETEK Programmable Power, Inc.
The Sorensen XPH Series provides 175 to 420 watts of DC power. The XPH is a compact, high performance low cost power supply suited for benchtop applications. The Sorensen XPH Series uses combined switch–mode pre–regulation with linear post-regulation to provide performance comparable with an all linear design. The XPH features excellent line and load regulation with low noise and good transient response. The XPH Series is available in a single, dual and triple output for benchtop use.
-
Product
16 GHz Differential Probe with ProLink Interface
DH16-PL
Interface
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Solid State GaN (Gallium Nitride) Amplifiers
-
Fairview Microwave’s solid state GaN (Gallium Nitride) power amplifiers (also called SSPAs) feature broad frequency bands ranging from 30 MHz to 7.5 GHz and very high gain levels from 43 to 60 dB. These GaN SSPAs also show impressive harmonic response (-15 to -20 dBc) under worst case conditions. Saturated output power levels range from 10W to 100W with 20% to 35% Power Added Efficiency (PAE). All of our high power solid state GaN amplifiers from Fairview have internally regulated single voltage supplies. Our GaN SSPAs are designed to withstand environmental conditions such as humidity, altitude, shock and vibration with an operating temperature ranges from -40°C to +85°C. Some models are also equipped with integrated heat sinks and cooling fans. Most designs are EAR99.
-
Product
Digital Control Step Attenuator
-
RF Lambda’s digital control step attenuators are used to fine tune an RF signal using TTL control lines. Fast response time, various step sizes and overall attenuation ranges make these suitable for a variety of RF applications. Hermetically sealed options are available upon request.
-
Product
Single Channel Signal Buffer Module
-
Alliance Support Partners, Inc.
Signal quality problems caused by mismatched impedance can result in intermittent measurements and faulty diagnostics. This is most often observed when transporting a test program from one system to another, such as re-hosting it from an older generation system to a new one. The primary root cause of the impedance mismatch is the signal path from the UUT to the measurement instrument. The switching system technology often is responsible for much of the distortion. The Signal Buffer Module (SBM) is designed to receive a signal from the UUT with high impedance output and accurately reproduced it at the output for delivery to the measurement instrument. The SBM output matches the 50 ohm input impedance of most measurement instruments and result in significantly reduced signal distortion.
-
Product
Dual Mobile Comm DC Source w/ Battery Emulation
66319B
DC Power Supply
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections. The Keysight 66319B dual output mobile communications dc source provides two outputs for testing both the main battery power and the battery charger circuitry, allowing customers to test phones and chargers with the same equipment. This feature helps save on rack space (2 outputs in a rack box) and eliminates the need for two separate power supplies.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 2.04k Ohm - SPST
50-294-122
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Electromagnetic Testing
-
Xiamen IDEA Electronic Technology Co., Ltd.
Is the process of inducing electric currents or magnetic fields or both inside a test object and observing the electromagnetic response.
-
Product
Connect Generators to the Grid
GridCode
-
DIgSILENT has developed a new verification tool called DIgSILENT GridCode. The software has been designed in response to the need to verify whether a conventional or renewable power plant is compliant with local Grid Code interconnection requirements on basis of generating unit tests. There is a new trend towards verification of requirements at the point of interconnection of a power plant using transient stability simulations with numerical models. An increasing number of Transmission System Operators are including model validation methods to quantify the risk and uncertainty when using these simulation models in stability studies. These new methods have been included in the DIgSILENT GridCode tool.
-
Product
Flowmeters for Compressed Air and Specialty Gases
Type SD
-
*Measurement to ISO 2533 and DIN 1343*For compressed air in industrial use as well as argon (Ar), carbon dioxide (CO2), nitrogen (N2)*Large measuring range up to 700 Nm³/h*Fast response time and high response sensitivity*With volumetric flow quantity, total quantity and temperature indication
-
Product
Motion Control
-
ADLINK motion control solutions have been widely adopted, to date driving over 700,000 axes industry-wide. ADLINK’s extensive field experience has driven the development of powerful, high-efficiency rapid response pulse motion controllers, real-time network controllers such as EtherCAT, Ethernet and MotioNnet, and application-level software for operating control systems with over 400 APIs
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
-
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
PXI Resistor Module 2-Channel 2R to 32.7k
40-293-032
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Non-contact Sensors
SENSOR NAVI
-
The easy system check is a function that allows easy checking of the compatibility or incompatibility between products and accessories, but does not guarantee all combinations.- Since the information provided through this system consists of approximate estimates, Mitutoyo declines any responsibility regarding damages that may arise from such information.
-
Product
PCI High Density Resistor Card 18-Channel, 8 Bit, 0 To 255 Ohm
50-295A-121-18/8
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Temperature Measurement IR Sensors & Detectors
ST60 TO-5
-
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 0.61mm x 0.61mm in a TO-5 package. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
- RS-422 and RS-485 Lightning/Surge Protector
Model 22NX
-
FEATURES: Triple Stage Protection; Fast Response Time For RS-422 / RS-485; Prevents Damage to Modems, Converters, and Terminals; Accommodates Data Rates to 10 MBPS; Supports 4 Circuits. The Model 22NX Lightning Sponge is designed to accommodate high-voltage transients, slow them down and redirect them to a low impedance path to earth ground.
-
Product
OEM CCD Camera
Syncerity BI-NIR Camera
-
The TE-cooled back illuminated 2048 x 70 CCD Camera combines affordability, performance and versatility for OEM applications. With peak QE of 84% @ 700nm and 20% at 1050nm, Syncerity BI-NIR offers a relatively broad response and addresses multiple applications. In the near-NIR, this detector is a much lower cost alternative to a deep depleted CCD, with no etaloning. Syncerity’s flexible design allows our OEM-dedicated team to quickly adapt the camera for industrial requirements, ranging from alternate CCD chips to electronics
-
Product
Compact Inductive Proximity Sensor
GA-311/GH
-
Panasonic Industrial Devices Sales Company of America
With a 3.3kHz response frequency, the GH Series Inductive Proximity Sensors are ideally suited for applications that require sensing of high-speed moving objects. These Proximity Sensors have the same form factor as Panasonic’s FX-300 Series Fiber Sensors and use the same shape quick-connection cables which, when used together, require minimal mounting space, but more importantly less power and wiring.
-
Product
JTAG Boundary-Scan I/O Modules
SCANIO Family
-
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
Product
PXI Source Measure Unit
Source Measure Unit
PXI Source Measure Units (SMUs) combine high-precision source and measure capability with features designed to reduce test time and increase flexibility. These features include high channel density for building parallel SMU test systems, deterministic hardware sequencing for minimizing software overhead, and high-speed update and sample rates for quickly changing setpoints and acquiring data. Additionally, the flexible sampling rate and streaming capability of PXI SMUs allows you to use the instrument as a digitizer to capture transient behavior, and the digital control loop gives you the ability to adjust the transient response of the instrument. The ability to change the transient behavior of the SMU, called SourceAdapt, reduces SMU settling time and minimizes overshoot and oscillations, even with highly capacitive loads.
-
Product
Signal Converters For Temperature Measurement In Direct Drive Motors
EIB 5000 series
-
*Reduced cabling*Overload protection for direct drive motors*Faster response behavior for excessive temperatures*Greater cost-effectiveness
-
Product
Photometers & Colorimeters
-
Instrument Systems Optische Messtechnik GmbH
A photometer is used to measure the photometric quantities of illuminance (lx), luminous intensity (cd), luminous flux (lm), and luminance (cd/m²). The integral method and the fast response time of silicon photodiodes means that photometers can achieve an outstanding measuring speed. They are therefore ideal for performing fast goniophotometric measurements. We take great care in the development and production of photometer heads and use innovative amplifier technologies.
-
Product
RZ Family of 64-Bit & 32-Bit Arm-Based High-End MPUs
RZ/T
-
The second products in the RZ Family. These high-end controllers leverage tightly-coupled memory to achieve high speed and high responsivity, and also support multi-protocol industrial Ethernet communications.
-
Product
PXIe-4163, 24-Channel, ±24 V, 50 mA PXI Source Measure Unit
784483-01
Analog Input Module
PXIe, 24-Channel, ±24 V, 50 mA PXI Source Measure Unit—The PXIe-4163 is a high-density source measure unit (SMU). It features 4-quadrant operation with a current resolution of 100 pA and the ability to sample up to 100 kS/s. The module also offers the ability to maximize stability and measurement accuracy with SourceAdapt, which allows you to custom-tune the transient response to match the characteristics of any load. The PXI-4163 is ideal for a broad range of mixed-signal integrated circuits (ICs) in semiconductor production test.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm - SPST
40-294-112
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Resistor Card 5-Channel, 16-Bit, 0 To 65k Ohm
50-295A-021-5/16
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Smart Analog IC101
-
Flexibly change analog front end (AFE) settings in response to environmental changes
-
Product
RGB Digital Fiber Optic Amplifier
CZ Series
-
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
