Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
product
MAX31855 K-Type Thermocouple Arduino Shield
SEN-30004-K03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855K supports a measured temperature range of -270C-1372C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
HeavyPower & EasyPower
Transformer Series
Transformer Series offers a customer configurable architecture, with just a few piece parts to create several types of connectors as a platform solution. No special tools are needed except crimping tools, resulting in a reduced stock and kitting/logistic management. The series offers a high reliability due to the Tortac® contact and provides up to 500 mating cycles and high current rating up to 300A/500A.
-
product
High Performance Embedded Development Kit
TySOM EDK
The TySOM™ Embedded Development Kit is for the embedded designers who need a high-performance RTL simulator/debugger for their embedded applications such as IoT, Automotive, Factory automation, UAV and Robotics. The kit includes Riviera-PRO™ Advanced Verification Platform and a TySOM development/prototyping board. TySOM boards come with either a Zynq 7000 chip (FPGA + Dual ARM® Cortex™-A9) or with a Zynq® UltraScale+™ MPSoC device. These boards include memories, and various communication and multimedia interfaces in addition to FMC connectors for peripheral expansion. Reference designs for application such as IoT, ADAS, 4K UltraHD imaging and Robotics and a complete reference design, which contains the SW (Linux) and all the hardware blocks required to support the peripherals on the board, are provided.
-
product
Interferometers
Sumix interferometers are designed for inspection of fiber optic ferrules, patch cords, pigtails and bare fiber in the process of polishing and assembly. They enable you to check polishing quality, test connector end face geometry per IEC, Telcordia or your own custom standards and generate reports to supply with your patch cords.
-
product
PXI/PXIe RF Matrix, 8x4, 100 MHz, 75 Ω SMB
42-729A-101
The 40-729A-101 (PXI) and 42-729A-101 (PXIe) are 8x4 75 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector. They provide a simple and scalable bidirectional matrix for RF signals and are intended for the construction of high performance switching systems.
-
product
Rugged Connectors
Guaranteed for a minimum of 100,000 connections, our rugged connectors are designed to meet your industrial & ergonomic demands in harsh testing environments. We offer numerous connector specifications all fitted with interchangeable spring loaded test probes. Supplied as a single hand held unit, panel mounted or fitted to a test lead, the combinations are limitless. Designed directly from your CAD data and thoroughly tested, our rugged & reliable connectors are used worldwide on a daily basis.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-118-M62.5
The 40/42-852A-118-M62.5 is a PXI/PXIe 8-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
Environmentally-sealed plastic connector
REP Series
Smiths Interconnect’s REP series is easy to use for quick mating. The REP panel and cable connectors are a highly cost-effective interconnect system, which solves the constant need for simple and reliable connector solutions in rail applications.
-
product
PXI Multiplexer Dual 24 Ch 1 Pole
40-632-021-D/24/1
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole, 4-pole and 1-pole screened.
-
product
Cable Assembly 15-Pin D-Type, Male to Female, 1m
40-970-015-1m-MF
The 15-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Male screwlocks are provided to secure the connectors to their associated products. The 15-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
22-Pin REDEL High Voltage Cable Assembly, Male to Unterminated, Cut Ends, 0.25A, 2m
A022KMR-C-HA200
This is a 2m long male to unterminated 22-Pin REDEL high voltage cable assembly with cut ends constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips are provided to secure the connector to associated product.
-
product
Cable Assembly, 200-Pin LFH, Female (Female Screwlocks) to 4x50-Pin IDC, Female, 2m
40-971B-200-2m-FF
This female rear exit to female ribbon 2m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to its mating connector by female screwlocks
-
product
YAV Modules
All YAV modules from 6TL Engineering are matching the most widely used mass interconnect (MIC) systems from Virginia Panel Corporation. It is easy and fast mounting a standard VPC 90 series connector module.
-
product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Ferrules, 1m
40-972-015-1m-FU
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
product
20-Pin GMCT Cable, Female to Female, 16A, 0.5m
40-970B-020-0.5m-FF
The 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Ferrules, 1m
40-972-160-1m-FU
A range of DIN41612 cable assemblies with unterminated connections on one end. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
product
Cable Assembly, 104-Pin D-Type, Male to Unterminated, Tinned Ends, 2A, 2m
A104HMR-T-0A200
This 2m long male to untermiated 104-Pin D-type Cable Assembly is suited for direct connection to various products using the 104-Pin connector. It is constructed from high-flexibilty, high-specification fully screened cable and is unterminated with tinned ends.
-
product
8-Pin Power D-Type Cable, Female to Unterminated, 0.5m
40-972-408-0.5m-FU
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
product
LXI Dual 8:1 Optic MUX FC/APC Loop-Thru
60-850-022
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
Torque Wrenches
Recommended torque for various connectors has changed slightly through the years, current standards often being slightly less than before. The recommended torque depends upon whether a connector is stainless steel or brass. The SMA recommended torques have the most variables, with stainless steel sma's for final installation being 8-10 in-lbs, preferably 8; stainless steel sma's in the test lab are best tested at 5 in-lbs to preserve the sma; & brass sma's are 4 in-lbs. Most of these torque wrenches are "ours" however we also carry the Huber Suhner sma torque wrenches, the 74Z-0-0-21 & 74Z-0-0-79 as they're so popular. Our torque wrenches are preset to specific values.
-
product
PXI Microwave Relay, Dual SPDT, 26.5GHz, 50Ω, SMA, External Termination
40-781A-322
The 40-781A-322 (PXI) and 42-781A-3221 (PXIe) are dual SPDT 26.5GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Ferrules, 0.5m
40-972-009-0.5m-MU
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass
40-860A-512-M
The 40/42-860A-512-M is a PXI/PXIe single insert/bypass switch with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 4-Bank 18GHz SMA
60-801-204
The 60-801-204 is a 6-channel, 4-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
GPS, GLONASS, Galileo Micro Splitter 2 Way, SMA, 1176.45 - 1602.00 MHz, 50 Ohm, Passive
GPSL10
INSTOCK Wireless Components, Inc
GPSL10 is a two way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Max voltage rating is 50 VDC; maximum current rating is 1000 mA. Furnished with SMA female connectors all ports. Being a "micro-sized" splitter, GPSL10 weighs only 21 grams and is suitable for applications requiring low-weight parts.
-
product
PCB Adapter, Receiver, TriPaddle, 96 Position, To PCB-Mounted 1x96 Male DIN 41612 Connector
510104139
The 96 Pin Signal receiver module is made from Ryton R-7, withstanding temperatures up to 220°C. Nomenclature is molded on the module.
-
product
NDX OOB Gateway
The Kronback Tracers NDX OOB Gateway is placed in the headend for NDF/NDR - narrowband digital forward/return interfacing. It consists of 3 NDF inputs (70 to 866 MHz) and 6 NDR outputs (5 to 65MHz). Each of the 3 NDF inputs transmits one narrowband range up to mode 7 (25.6 MS/s), including the full FM band 87.5 to 108 MHz. Each of the 6 NDR connectors outputs up to three narrowband signals from the RPD with a bandwidth up to mode 6 (5.12MS/s).
-
product
Adjustable Phase Trimmer, DC to 18 GHz, with an Adjustable Phase of 10 Deg. Per GHz and SMA
PE8203
Pasternack adjustable phase trimmer PE8203 is part of our large selection of in-stock RF, microwave and millimeter wave components available for purchase. This adjustable phase trimmer is manufactured with SMA connectors and has a phase adjustment of 10 degrees. Our SMA adjustable phase trimmer has a minimum frequency of DC and a maximum frequency of 18 GHz.
-
product
GaN 100W Power Amplifiers
PE15A5033F
The PE15A5033F is a 100 W high gain Class A/AB Coaxial Linear Power Amplifier operating in the 0.7 to 2.7 GHz frequency range. The amplifier offers 100 Watts typical saturated power and 45 dB minimum small signal gain with 1.5 dB typical gain flatness @ Psat. The amplifier requires typically a +30V DC power supply. The SMA connectorized module is unconditionally stable and operates over the temperature range of 0C and +50C. The unit comes with a Heatsink and Fan.
-
product
Accessories
Universal LightProbes are easily installed with one-hole fixing. Optomistic Products provides several accessories to make the use and installation of Universal LightProbes fast and simple, including The Sensor Six-Pack, Sensor and Fiber-optic Probe clamps, and Universal LightProbe Connector Cables.
