-
product
Load Monitoring Units (LMUs)
Magtrol's Load Monitoring Units are used for measuring load, force and weight from signals generated by strain gauge transducers. Specifically designed for use with Magtrol's Load Measuring Pins and Load-Force-Weight Sensors, the LMU Series provides excitation voltage while conditioning the bridge output signal. Each unit contains DIP-switches and jumpers for greater flexibility and complete adaptability
-
product
2 PRI + 4 Port FXS PSTN Simulator Adv
CH-4FXS-MOD-2PRI-A
One of the most feature rich PSTN simulator on the market. Unit has 4 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
product
PCI To PCI Express Board
MS 1718
PCI to PCI Express card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit PCI signals from/to the Host System. These PCI signals are converted into PCI Express using PCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
product
20-slot ATX-supported Bridged PICMG Bus Active Backplane
ATX6022/20GP18
*1 PICMG, 18 PCI and 1 ISA*Compatible with AX61492 chassis*Supports both AT and ATX power supply
-
product
Instrument Grade Data Sensor
WISER 8000
TECAT Performance Systems, LLC
The TECAT WISER Model 8000 dual strain measurement and monitoring system is a wireless data acquisition system for measuring two external strain channels at high data rates up to 8kHz. The small, light, power-efficient, and non-invasive design enables strain measurements in a wide range of applications. With dual external sensor inputs two Micro-Measurements strain gauge bridges can be measured by a single system, for example to measure both thrust and torque loads simultaneously.The Model 8000 has a long range data transmission of >1,000 meters with up to +/- 0.025% FSR sensitivity for remote measurements. After initial setup using the WISER software interface, the system can be wired directly to your DAQ system, for seamless data collection.
-
product
Backplane
P47
VECTOR Electronics and Technology, Inc.
Power supply backplane provide a modular approach for the addition of plug-in, hot-swap power supplies. As a result there is no need to modify expensive backplanes to incorporate redundant power supplies or N+1 configurations. Multiple power supply backplanes may be bridged together for additional power supply requirements.
-
product
Fanless Embedded System With Socket G2 Intel® Core™ I7/i5/i3 & Celeron® Processor And 4 GbE LANs
eBOX660-872-FL
A high-performance fanless embedded system with 3rd Generation Intel® Core™ processor (Ivy Bridge), the eBOX660-872-FL, is presented by Axiomtek earnestly. It incorporates the 3rd Generation Intel® Core™ processor (i7/ i5/ i3) or Intel® Celeron® processor with Intel® HM76 Express chipset, propelling computing with better processing. With the great graphics computing capability and dual view support, this fanless embedded box computer is especially suited for automatic optical inspection, digital signage (DS), digital surveillance, gaming, automation control and POS/Kiosk. In addition, this application-ready compact rugged platform also targets for nearly any field of industrial embedded applications like embedded controller, factory automation and more fields.
-
product
Bridge Rectifier Assemblies
Bridge Rectifier Assemblies are constructed by packaging diodes and/or SCR components with heat sink extrusions in a bridge circuit.CEHCO uses M, T, N and W heat sink extrusions to build rectifier assemblies.
-
product
Variable Reluctance Pressure Sensor with All-Welded Construction
DP10
The DP10 Pressure Sensor, is designed for low and medium pressure measurements, to laboratory accuracy, of corrosive liquids and gases. In typical AC excited bridge circuits, this transducer delivers a full scale output of 30 mV per volt at 3kHz. The unit operates with carrier system including the Validyne CD15 since wave carrier demodulator and CD16 miniature DC input DC output carrier demodulator.
-
product
Load Cell Amplifiers
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
product
Bridge Monitoring
Structural Health Monitoring of BridgesDewesoft data acquisition systems are used in structural health and seismic bridge monitoring projects ranging from structural mechanics to continuous monitoring of large, complex structures. The systems provide distributed, high-channel-count and remote monitoring for highway overpasses, roads, buildings, and bridges.
-
product
Programmable Limit Switch (PLS)
AMETEK Sensors, Test & Calibration
The Gemco Programmable Limit Switches (PLS’s) are used in a variety of applications from packaging and stamping to every day factory automation. In the Heavy Moveable Structure Industry, they can typically be found in Rail and Draw Bridge Control Houses. These devices are typically found in applications where the PLC scan time cannot keep up with the process.
-
product
Precision LCR Meter (20Hz to 2MHz)
ST2840
ST2840 series pricision LCR meter innovatively adopts a new generation of technologies such as dual CPU architecture, Linux bottom layer, 10.1-inch capacitive touch screen, built-in instruction which effectively solves the defects of slow LCR test, single display and complicated operation in the past.The measurement frequency of ST2840 series is from 20Hz-500kHz/2MHz, which makes up for the shortcoming of lack of high-performance bridge in the frequency range of 500kHz.
-
product
Bridge Device and GPIO Port Expander
SPI-to-I2C
The CP2120 compact SPI-to-I2C bridge and general purpose port expander device can be easily added to a system to solve interface compatibility problems and add more GPIO when required.
-
product
LOCAL LOOP SIMULATOR FOR TR-114 INCLUDING BRIDGED TAP
458-LM-A1-30-TR114
The Model 458-LM-A1-30-TR114 Local Loop Simulator for TR-114 is the ideal solution for simulating test loops as defined in TR-114 and includes a Bridged Tap. In addition, it is also suitable for ADSL, ADSL2, ADSL2+, and VDSL2 chip/modem/DSLAM testing of straight loops out to 24,000
-
product
6U Form Factor PMC/PrPMC Carrier-VMEbus
i4400
The i4400 is a low-cost 6U form factor PMC / PrPMC carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating two single PMC modules or one double PMC module in a VMEbus system. The current version of the i4400 supports PMC modules and also supports Processor PMC modules on one PMC-site. The VME-to-PCI bridge is implemented in an FPGA for flexible VME-to-PCI mapping and to allow future updates and upgrades.
-
product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
product
PXI Strain Gauge Simulator Module 4-Channel, 2k
40-265-304
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Ethernet Connectivity for Controlling ARINC-429 Channels and Auto RX Bridging
ENET-A429
eNet-A429™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). eNet-429 is a small, low-power, rugged device that provides connectivity for 1-8 ARINC 429/575/573/717 Channels – Ideal for remoting ARINC connections for in-field applications or point-point lab usage.
-
product
Fast USB Strain Module
FSU-SSB
The FSU-SSB is a fast, compact, high precision strain bridge input module delivering high resolution readings over USB and communicated directly to a PC. It is aimed at dynamic applications that require high speed measurement.It delivers high speed measurements of 4800 samples per second at 13 bits noise free resolutio
-
product
65 lane, 17 port, PCI Express
PEX 9765
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe. Yet ExpressFabric works seamlessly with other standards used within the rack and in rack-to-rack connectivity.
-
product
Precision Thermometer
F252
ASL's F252 provides high accuracy, dual channel temperature measurement with Platinum Resistance Thermometers - PRTs - and uses AC bridge technology as developed by ASL for Standards Laboratories throughout the world. Model F252 requires no regular recalibration, the AC circuit techniques eliminating thermal EMFs and drift, while providing excellent long term stability. Front panel data entry allows you to enter probe calibration data into the F252's memory, so that thermometer resistance can be accurately converted to temperature in C, F or K. This can be password protected to prohibit unauthorised or accidental data entry.
-
product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
product
CAN MiniModules
CAN STG6 MiniModule
Precise measurement of mechanical strain, directly at the point of application of the strain gauge: realized via the CAN-based measurement module STG6 BK10 with six strain gauge inputs for quarter-, half- and full bridges.
-
product
Software Solution for Interoperability Testing
COMPRION Network Bridge
COMPRION Network Bridge provides a direct connection between (e)UICCs and back end servers. This way, remote administration scenarios can be processed in a lab environment independent of a real network or a network simulator. This makes the work of (e)UICC manufacturers, MNOs, SM-DP(+), and SM-SR providers easier. The test effort is reduced significantly, because there is no need for a network simulator and the testing limitations of a real or simulated network do not apply.
-
product
Rugged Door Contact Sensor with Universal-Style Magnet
ENVIROMUX-DCSR-U
Monitors access with a magnetic bridge sensor (no special inserts necessary). Ideal for commercial and industrial installations in harsh environments. Heavy-cast aluminum housing with 18-inch stainless steel armored cable. Floor-mounting hardware included. Universal-style magnet option has a smaller width and depth that provides greater installation flexibility. For normally open or normally closed circuit connection. Wide actuating gap, approximately 3". Maximum cable length: 1,000 ft (305 m). Dimensions WxDxH (in): Magnet: 3.13x0.81x2.13 (79x21x54 mm), Switch: 3.5x1.5x0.44 (89x38x11 mm). Regulatory approvals: UL.
-
product
AMR Magnetic Scale Sensors
MultiDimension Technology Co.,Ltd.
Magnetic grate sensors integrate two push-pull Wheatstone bridges, each of which contains four high-sensitivity anisotropic magnetoresistance (AMR) sensing elements. Such a design effectively compensates temperature drift to ensure high accuracy under wide temperature range.
-
product
PXI Strain Gauge Simulator Module 6-Channel, 2k
40-265-306
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Custom Energetics
Excelitas has extensive experience with designing, manufacturing, and testing a wide range of energetic components including actuators, detonators, initiators, and timers. The products are manufactured to precise standards enabling high reliability and consistency from device to device. The initiation mechanisms include exploding foil initiators (EFI), exploding bridge wire (EBW), and laser initiators. Detonators, actuators, and timers are manufactured and tested as build-to-print products for the NNSA.
-
product
Maritime
Nieaf-Smitt maritime instruments are designed, engineered and manufactured for bridge, bridge-wing and control/rudder room applications on board of ships. Prime applications such as propulsion, steering and navigation are covered with a wide range of dedicated products.





























