Product

In-Circuit ESR & DCR capacitor Tester

236

-

GME Technology

236 - GME Technology

This In-circuit ESR & DCR capacitor tester is designed to measure ESR (equivalent Series Resistance) on capacitors range from 0.47uF to 2200uF, in or out of circuit. The ability to trouble shoot in-circuit saves time and makes the 236 a must for anyone that tests or trouble shoots PCB (printed circuit boards).

Product

SOIC and SOJ-to-DIP Adaptor

Series 45000X & 65000X

-

Aries

Series 45000X & 65000X - Aries

SOIC & SOJ to DIP Adapters. A cost effective means of upgrading to SOJ or SOIC...without changing your PCB layout.

Product

Exchangeable Test Fixture

MA 2109/D/H/S-5

-

INGUN Prüfmittelbau GmbH

MA 2109/D/H/S-5 - INGUN Prüfmittelbau GmbH

Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 8,50 kg

Product

High-speed 3D Solder Inspection Machine

YSi-SP

-

Yamaha Motor IM

YSi-SP - Yamaha Motor IM

a high-speed 3D solder paste inspection machine that enables high-speed high-accuracy inspections based on our “1-head solution” concept for using a single type of head to handle various inspections. It is used to inspect the printing quality (volume, height, area, misalignment) of solder paste after it has been printed onto PCBs. Available April '18.

Product

Relay Sockets & Accessories For Power Relays

-

Mors Smitt Group

Mors Smitt Group

Suitable for 35mm rail (DIN), wall or PCB mounting, timer modules, key receptables and retaining clips. See below for all models/series.

Product

44-Pin D-Type Connector, Female, Right Angled PCB Mount

40-963-044-RF

-

Pickering Interfaces Inc.

40-963-044-RF - Pickering Interfaces Inc.

Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.

Product

SMP Connectors

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

Pasternack SMP connector (sub-miniature push-on connectors) category contains mostly RoHS and REACH compliant product varieties. The SMP connector category includes dozens of configurations including coaxial sub-miniature push-on connectors, PCB mounted, non-sealed and hermetically sealed terminals and shrouds. Our subminiature push-on SMP connectors are built to precise microwave and RF industry specifications and are part of over 40,000 in-stock RF products. Connectors in SMP series from Pasternack are manufactured in male or female gender with a 50 Ohm impedance. Pasternack's SMP subminiature connector are available in straight or right angle versions as well as bulkhead or mount-less options. These connector designs include solder or solder/solder attachment methods. Pasternack’s SMP connectors are miniaturized push-on interconnects commonly used in high density, blind-mate systems that can operate up to 40 GHz. Standard sub-miniature push on connector items are offered in a high frequency 40 GHz version as well as a low frequency 8 GHz version and are also available in smooth bore, limited detent and full detent styles. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMP connector series is in-stock. Not just in stock, these subminiature push on connectors will also ship the same day as they are purchased.

Product

PCB High Sensitivity, 100mV/g, ICP® (IEPE) Accelerometer

780989-01

-

NI

780989-01 - NI

The PCB HSTC33 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB HSTC33 features a sensitivity range of 100 mV/g and requires a low-noise coaxial cable.

Product

4 Pin Power D-Type Male Connector, 40A, PCB Mount

40-963-004-RM

-

Pickering Interfaces Inc.

40-963-004-RM - Pickering Interfaces Inc.

This connector is suitable for Pickering Interface's modules that use the 4-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.

Product

ABex Terminal Module for Göpel 1149Cx BSCAN Cards

ABex TM-1149Cx

-

Konrad Technologies GmbH

ABex TM-1149Cx - Konrad Technologies GmbH

The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.

Product

Measuring Small Antennas

-

MegiQ BV

MegiQ BV

If you have a small PCB with a small antenna you can't use a thick cable and a large connector. Not only is this impractical (how to connect the connector?) but the metal bulk will also affect the antenna and grounding properties of your PCB. The measurement will be useless. MegiQ promotes the use of the small and popular UFL connector and its associated cables. The UFL socket fits on almost any PCB and it can be improvised on a board without a UFL footprint.

Product

Cost-Effective ATE System

PRO RACK ATE

-

Qmax Test Technologies Pvt. Ltd.

PRO RACK ATE - Qmax Test Technologies Pvt. Ltd.

Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.

Product

EMI Tester

-

Peritec Corp.

Peritec Corp.

The EMI tester automatically measures the noise distribution of the electric field and　 the magnetic field radiated from electronic equipment with high accuracy.・ Even if PCB and IC parts have complicated bumpy shape and surface. 　 The movable assembly can automatically trace them.・ EMI noise distribution is expressed as a variety of maps, such as 4D/3D/2D graphics 　 and cross section view.

Product

Linear Testfixture (Cassette Not Included), UTT 306 x 248 mm

MG-02

-

MG Products

MG-02 - MG Products

FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for changeable cassette

Product

MEMS DC Response Accelerometers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB® series 3711F, 3713F, 3741F, and 3743F MEMS DC response sensors are used to measure low frequency motion down to zero hertz. These accelerometers are used in applications such as structural monitoring, aerospace vibration testing, drivability, and gravitational force measurements. Each series includes a full scale measurement range from ± 2g to ± 200g and features low spectral noise with high resolution.

Product

Exchangeable Test Fixture

MA 2112/D/H/S-7/GR228x-15/15

-

INGUN Prüfmittelbau GmbH

MA 2112/D/H/S-7/GR228x-15/15 - INGUN Prüfmittelbau GmbH

Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,46 kg

Product

In-Circuit Test Fixtures

-

Circuit Check, Inc.

Circuit Check, Inc.

In-circuit testing provides electronic manufacturers a reliable, high fault coverage verification method for the assembly process. Circuit Check ICT fixtures are robust, reliable and designed for easy customization to cover a large range of PCB sizes without impacting turnaround time. We stock a large variety of fixture sizes and actuation methods to meet your test demands. If a stocked sized ICT fixture is not adequate our engineering staff will design a custom solution.

Product

Multiple Instrument Station

SYSTEM 8 MIS 4

-

ABI Electronics Ltd

SYSTEM 8 MIS 4 - ABI Electronics Ltd

The Multiple Instrument Station MIS4 provides you with all the instruments required for the test and measurement of electronic components and PCBs. ABI's SYSTEM 8 MIS4, along with the Ultimate software, is a faster and more economical solution than using traditional oscilloscope, metering and other bench test instruments, and can quickly produce the required Pass/Fail or other test and debug results.

Product

PCB Connectors

2mm / cPCI Series

-

Smiths Interconnect

2mm / cPCI Series - Smiths Interconnect

Smiths Interconnect's cPCI Series offers extremely high reliability in a cPCI standard envelope.

Product

Circuit Simulation & PCB Design Software

TINA Design Suite

-

DesignSoft, Inc.

TINA Design Suite - DesignSoft, Inc.

TINA Design Suite s a powerful yet affordable circuit simulation and PCB design software package for analyzing, designing, and real time testing of analog, digital, HDL, MCU, and mixed electronic circuits and their PCB layouts. You can also analyze SMPS, RF, communication, and optoelectronic circuits; generate and debug MCU code using the integrated flowchart tool; and test microcontroller applications in a mixed circuit environment.

Product

PCB Design Software

-

Proteus

Proteus

Proteus PCB Software combines Schematic Capture and PCB Layout modules to provide an affordable, powerful and easy to use suite of tools for professional PCB design.

Product

Universal SOIC-to-0.600 [15.24] DIP Adaptor

Series 647

-

Aries

Series 647 - Aries

Universal SOIC to .600 [15.24] DIP Adapter. 44 pin adapter for mounting Aries Series 547 Universal SOIC ZIF (zero insertion force) Test Socket to .600 [15.24] DIP PCB layout. Consult Data Sheet No. 10015 for test socket information.

Product

Colorimeter​​

Model CA-600​​​

-

Teledyne Analytical Instruments

Model CA-600​​​ - Teledyne Analytical Instruments

The​ CA600 is an online sequential sampling analyzer, using colorimetric methods. The analyzer can be configured to most laboratory colorimetric tests in individual processes.The CA600 Analyzers are easy to start up and use, simply connect the sample, waste and reagent lines and then power up the factory calibrated analyzer.​ Wall mount hardware is standard but an optional bench-top stand with reagent holder is also available. Accessing information for customizing an analysis routine is easily accomplished with the simple, user friendly menu structure and touch screen interface.The analyzer has two separated enclosures with two lockable doors. The top enclosure, called the electrical enclosure, includes the main power supply, the controller PCB assembly and the touchscreen interface. The bottom enclosure, called the liquids enclosure, includes all the components involved in the sample and reagent flow, mixing and reaction stages (sampling pump, reagent micro pumps and colorimetric reaction cell). Numerous analysis configurations can be programmed, depending on the accessories and the number of micro-pumps mounted in the liquid enclosure.

Product

USB3 Vision Cameras

xiQ

-

XIMEA GmbH

xiQ - XIMEA GmbH

*Ultra compact mini camera- Only 26.4 x 26.4 x 21.2 mm and mere 27grams (1)*Cool - Low power consumption with 1.0 to 1.8 W and minimal heat dissipation*Fastest - High speed, high frame rate: 500fps at VGA and 90fps at 4Mpix resolutions*AIA standard - USB3 Vision standard compliant*Supported - USB3 under Windows 7 and 10, macOS, Linux, ARM and various Machine Vision Libraries*Industry standard interface - Compatible with USB 3.1 Gen1 SuperSpeed specification*Powerful potential - 5 Gbit/s interface 400 MB/s data throughput*Connectivity and Synchronization - Programmable opto-isolated input and output, 3 status LEDs*Cost efficient - Excellent value for the price, low TCO and fast ROI*Software interfaces - GenICam / GenTL and highly optimized API / SDK for Image Processing*Easy deployment - Range of accessories and widest hardware and software interoperability*Time proven - In production since the end of 2011*User friendly - Intuitive and simple to use API, easy switch from C to CS mount and more*Highly Customizable - Available in Board level (single PCB) and with different connector types

Product

PCB High Sensitivity, 100mV/g, ICP® (IEPE) Accelerometer

784170-01

-

NI

784170-01 - NI

The PCB HSTA15 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB HSTA15 features a sensitivity range of 10 mV/g and requires a 4-socket plug-to-3 BNC plug cable.