PCB
See Also: Printed Circuit Board, PCBA, Crosstalk
-
Product
RF Connectors
HD-EFI Connectors
-
The HD-EFI product series is a micro-miniature interface designed to allow large board tolerance stack ups, blind mating, and multiple RF lines. It is available in common PCB jack and cable plug configurations, with an assortment of bullet adapters to accommodate many board to board spacing options.
-
Product
9 Pin D-Type, Male, Straight PCB Mount, HV
40-963-009-SM-HV
D-Sub PCB-Mount Connector
9-Pin Male D-Type Connector, High Voltage - Straight PCB Mount
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Open Standard Module (OSM)
-
Advantech's OSM, the SGeT standard for PCB soldering design with NXP platforms, boasts an ultra-low power, miniaturized design for AIoT endpoints.
-
Product
Digital to LVDT RVDT Converters
ST-DLVT
ITA
Computer Conversions Corporation
ST-DLVT series - Complete Digital to LVDT RVDT Converters On PCB with Mounting Track having Screw-Terminal Block for ease of wiring. 2 or 3-4 wire output configurations, Isolated Reference & Signals, 3V and 5V logic Compatible
-
Product
Detectors
-
Thorlabs' photodetectors are capable of detecting light throughout the UV, VIS, NIR, IR, and THz spectral regions. Our photodetectors feature sensors that enable properties such as intensity, power, intensity distribution, wavefront shape, energy, and wavelength to be measured. We offer unmounted photodiodes as well as amplified, biased, and avalanche photodetectors. Thermal power detectors are available unmounted, mounted on a PCB, or mounted on an aluminum plate. Also available are position-detecting sensors, integrating spheres, and an acoustic detection module.
-
Product
CAT-5 Video Drivers
-
Analog Devices provides designers with a robust portfolio of high speed triple, differential, and single-ended input to differential output CAT-5 video drivers. We designed the technology for the highest resolution component video signals, but it can be used for any type of analog signals or high speed data transmission over either Category 5 UTP cable or differential printed circuit board (PCB) transmission lines. Manufactured with our second generation XFCB bipolar process, the drivers have large signal bandwidths of 700 MHz, fast slew rate, and output amplitude and phase matching balanced to –60 dB at 50 MHz.
-
Product
Software
CAD VIEWER
-
The CAD viewer layout software from Digitaltest is perfectly tailored to the requirements of electronic manufacturing and can be used in many different stages of the production. The software is designed to be intuitively, so that anyone can learn quickly the extensive functions. The CAD Viewer layout software from Digitaltest helps you to produce your PCBs fast and safely.
-
-
Product
PXI-4132, 100 V, 2 W Precision PXI Source Measure Unit
780558-01
Source Measure Unit
±100 V, 10 pA Precision PXI Source Measure Unit—The PXI-4132 is a programmable, high-precision source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4-wire) sense as well as external guarding. With its high measurement resolution integrated guarding, the PXI-4132 is ideal for high-accuracy leakage measurements on integrated circuits, discrete components, PCBs, and cables. You can also perform high-speed I-V measurements on a variety of components including diodes and organic LEDs using the onboard hardware sequencing engine. In addition, you can synchronize multiple PXI-4132 modules using the PXI backplane to provide high-speed I-V measurements on transistors and more complex devices.
-
Product
PTFE Insulated Terminals And Test Point Jacks
-
Ideal for High Temperature, high quality terminal and PCB connector applications.
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UUT 586 x 248 mm
MG-03-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 248 mm (wxd)• Outer dimensions: 750 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
Product
25-Pin D-Type Female Right Angled PCB
40-963-025-RF
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 25-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
Mini Coax, Module, Receiver, 90 Series, 19 Positions, for use with right-angle contact (p/n 610104160)
510104319
Receiver Module
Use with right-angle mini coax contact (p/n 610104160) for mounting to PCBs. Includes holes for PCB mounting.Primary mating module 510108111. (May mate with other ITA modules, as well.)
-
Product
Custom PCB Enclosures
Enclosure
Our customers have shared a long history of using printed circuit boards (PCB) in the interchangeable test adapters (ITAs) of their automated test equipment (ATE) stations. Whether you are designing a self-test fixture and want to save space, improve signal integrity, and/or reduce cable management headaches, VPC has a team of engineers with the expertise needed to help.
-
Product
1.0/2.3 Connectors
-
Pasternack 1.0/2.3 connector category has many part numbers, most are RoHS and REACH compliant. 1.0/2.3 connector series in this category will terminate to coax or PCB (printed circuit board). Our 1.0-2.3 connectors are built to precise RF and microwave industry specifications. 1.0-2.3 connector series is manufactured in jack or plug gender with 50 Ohm impedance. 1.0-2.3 connectors are available in straight or right angle versions, as well as, bulkhead or mountless options. These 1.0 / 2.3 connector designs include crimp/solder, solder or solder/solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 1.0/2.3 connector series is in-stock. Not only are these 1.0-2.3 connectors in stock, but they ship the same day as they are purchased.
-
Product
PLCC Clips & Socket Plugs
-
Ironwood’s family of clips and plugs for PLCC packages can be used for connecting PCBs together or for gaining access to signals for testing.
-
Product
EMI Tester
-
The EMI tester automatically measures the noise distribution of the electric field and the magnetic field radiated from electronic equipment with high accuracy.・ Even if PCB and IC parts have complicated bumpy shape and surface. The movable assembly can automatically trace them.・ EMI noise distribution is expressed as a variety of maps, such as 4D/3D/2D graphics and cross section view.
-
Product
50 Pin IDC Connector Accessories
-
Ideal for user created termination schemes where the termination is to be remotely connected to the module by cable. Interfacing PCBs should be designed with suitable clearance for the voltage that the application requires.
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle
KR100
Spring Probe
K100 Series, Pitch 100mil, Receptacle, no wire wrap pin. Brass with gold finish.
-
Product
37-Pin D-Type Female Straight PCB HV
40-963-037-SF-HV
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
32GB DDR5-5600 2GX8 1.1V SAM
AQD-D5V32GN56-SB
Memory Module
SAM Original Chip, PCB: 30μ gold finger, Anti-sulfuration, On-die ECC for Enhanced RAS, Operating Temperature: 0°C ~ 85°C.
-
Product
PCB Adapter, ITA, SIM, VTAC, 16 Pos, 6 Slot, to (1) Cat6
510171105
PCB Adapter (ITA)
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single Cat 6 connector. Great for COTS cable configurations. Compatible with all VTAC/SIM ITA modules. Please note this part is too wide for use in multiple adjacent slots.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/HG/KT-ITA-21
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 16,30 kg
-
Product
8G SO-DDR5-5600 1GX16 1.1V SAM -20~85℃
AQD-SD5V8GN56-SCH
-
SAM Original Chip, Industrial Design for Improved Reliability, PCB: 30μ gold finger. Anti-sulfuration, Semi Wide-temp Support -20~85℃.
-
Product
8GB SO-DDR5-5600 1GX16 1.1V SAM
AQD-SD5V8GN56-SC
Memory Module
SAM Original Chip, PCB: 30μ gold finger, Anti-sulfuration, On-die ECC for Enhanced RAS, Operating Temperature: 0°C ~ 85°C.
-
Product
Miniature Single Axis Accelerometers
-
Miniature piezoelectric accelerometers are required for applications demanding high frequency range, small size, and low weight. Product testing is necessary in today’s competitive marketplace in order to optimize designs, reduce defects, and improve customer acceptance and satisfaction. Shock and vibration testing offers a structured approach for verifying survivability in environmental influences that may be encountered during service and for precipitating incipient failures so they are not encountered by the end-user. PCB® accelerometers are used extensively for monitoring an object’s response to a programmed vibration input and for controlling the vibration profiles during testing.
-
Product
8 Pin Power D-Type Male Connector, 40A, PCB Mount
40-963-008-RM
-
This connector is suitable for Pickering Interface's modules that use the 8-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
-
Product
PCB Adapter, ITA, TriPaddle, 96 Position, To PCB-Mounted 1x96 Male DIN 41612 Connector
510108148
PCB Adapter
The 96 Pin ITA Signal Module is made from Ryton R-7, withstanding temperatures up to 220°C. Nomenclature is molded on the Module.
-
Product
Process Improvement
-
Omron’s numerous software solutions for quality control, process improvement, defect monitoring and more are ideal for PCB manufacturers seeking to boost productivity.
