Conductance
See Also: Battery Conductance Testers
-
Product
PXI 3A Power MUX BRIC, 18-Channel, 16-Pole
40-571-206
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Conductivity Transmitter
DO9766T-R1
-
output of a conductivity electrode with temperature compensation into a 4÷20 mA signal.
-
Product
Shielded and Unshielded Cable
-
Teledyne Marine Cable Solutions
Shielding Types• Braided I Served I Spiral• Foil & Hybrid• Vapor Barriers• Copper & Alloys• Conductive & Static Dissipative Tapes• Conductive Fabrics• Tensile Members• RFI & EMI Tapes & Braids (Serveor Interwoven)• Utilizing Flat & Round Copper• Stainless Steel• Bronze• Aramid Fibers & Textile, amongothersConstruction• Multi-conductor, shielded pairs, pairs with steel tubed fiber or copper conductors with fiber optics, coaxial conductors & aramid strength fibers
-
Product
MemoRail
-
Refers to a line of compact, modular transmitters used for industrial process analytics, specifically designed for monitoring pH, ORP, conductivity, and oxygen in various industries like chemicals, pharmaceuticals, and food/beverage.
-
Product
Conductive
VEGAKON, EL
-
When the electrodes of the conductive point level sensor come into contact with a conductive fluid, a small alternating current begins to flow.
-
Product
Analytical Services
-
Atomic Force Microscopy (AFM) allows for sub nanometer resolution imaging of surface topography and is able to quantify surface roughness at the angstrom scale. Our team can give you highly accurate measurements such as surface topography, dopant distribution, magnetic domain features, and a wide variety of other sample properties to give you the information you need to do great work.Park can provide measurements in the following areas:● Topography (surface roughness, grain size, step height, etc.)● Mechanical Properties (stiffness, etc.)● Electrical properties (capacitance, conductivity, etc.)● Thermal properties ● Magnetic properties These properties can be measured in air or liquid, depending on your needs.
-
Product
Transformer Test Panel/ Setup
-
This is a common test panel for distribution/ power transformers of different specifications. The user can perform most of the factory tests, as per the relevant IS standard for the transformers. The panel consists of power analyser, meters for high voltage test, meters for induced voltage test etc, control for all the tests, protection and interlock circuits so that a single panel can be used to conduct a number of tests using only one dimmerstat and the associated devices
-
Product
VPX Extender 3U All Differential - Conduction / Convection
119EXT3024-37XXR
-
VPX Test Extender 3U x 240mm for conduction cooled boards in convection chassis.
-
Product
PXI 3A Power MUX BRIC, 4-Channel, 24-Pole
40-571-102
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Compensating Reactor
-
The compensating reactors are accessories for the CTS-12KSA/ACTS-12K Capacitance & Tan Delta Test Set. The use of one or more compensating reactors increases the capacitance that the internal power supply can excite to conduct measurements. As the measuring range of the CTS-12KSA / ACTS 12K exceeds the kVA rating of the internal power supply, one way of using the test set over its entire measuring range is to form a resonant circuit with the test sample. The use of one or more compensating reactors forms partial resonating circuit with the test specimen, thereby reducing the power supply requirement.
-
Product
VPX/open VPX C-Frame 5 Slot 3U
-
Our 2nd Generation C-Frame offers the next level of flexibility in VPX development platforms. Not only can the customer exchange the type of card guides (convection, conduction, AFT) in a blink of an eye but now also the signal backplane. Thanks to Bi=/=Plane®technology, power and signal parts of a VPX backplane are separate PCB assemblies. This enables uncompromised signal quality along with faster turn around for the design of custom profiles.
-
Product
Detector And FPA Testing
-
The FPA Test Set (FPATS) interface to the detectors under test (DUT’s) is via a custom pedestal plate which provides both a conductive heat path to both the individual DUT’s as well as the field of view limiting aperture plate. This custom pedestal plate protrudes through the customer provided DUT interface printed circuit board (PCB) and makes physical contact with the rear of the DUT packages and the aperture plate when the FPATS is in the closed position. The pedestal plate is mounted to the ambient source plate and its temperature is actively driven by this subsystem.
-
Product
VPX Extender 3U VITA67.1 Conduction Cooled
1940000519-9001R
-
3U VPX Extender for conduction cooled boards mounted in conduction cooled chassis VITA 67.1 (VITA 67.1 connectors not included)
-
Product
VPX Development Systems
-
development system with Backplane Profile BKP6-CEN06-11.2.5-n. Specifically supports OpenVPX and VPX REDI 6U convection or conduction cooled boards and modules.
-
Product
TIM Tester
-
The Analysis Tech TIM Tester 1300 is an automated test system for measurement of thermal impedance and conductivity on thin, thermally conductive materials of the type frequently used for electronic packaging, as well as a wide variety of flexible or rigid solids and semi-liquid or viscous materials. Generally, the TIM Tester 1300 can accommodate samples with high-to-medium thermal conductivity with contact pressures ranging from 10 to 550 psi (70-3800 kpa) and at sample temperature ranging from 15C to 70C.
-
Product
PXI High Density MUX BRIC, 80-Chan, 10-Pole
40-570-415
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Inducitive Switch Transient Test Circuit
NSG 5071
-
The basic philosophy of this test circuit is better reproducibility of actual switching transients. The reproducibility of this test circuit comes not from the output characteristics as in traditional conducted automotive immunity tests, but from a fixed design of the generator using several pre-defined components. Many of these components are defined in the standard as "critical" with no substitutions allowed. These components are used as required in the standard.
-
Product
Application Performance Testing
-
An important part of application performance testing is to conduct such tests in conditions that realistically reflect the environment in which the application is ultimately expected to operate.
-
Product
Nutrient | Oxygen | PH Sensors: PH Sensors
-
pH (potential Hydrogen) is a measurement of the level of acids and bases in water. Our pH sensors have been used extensively to research ocean acidification, coral reefs, coastal marine biology, and to conduct environmental monitoring.
-
Product
HandHeld Portable Water Activity Meter WA-60A
WA-60A
-
Guangzhou Landtek Instruments Co. Ltd.
Applications:Can be used to measure the water activity of foods. No matter when and where you need to measure water activity, WA-60A water activity meter is your unique choice.The Water Activity, mainly reflects the amount of free water in the state of food balance, the stability of food and the possibility of microbial reproduction, and the chemical,enzyme and physical changes that can cause the change of food quality.It is often used to measure the dryness enduring ability of the microorganisms. Bymeasuring the water activity of food and selecting reasonable packing and storage methods,the use of preservatives can be reduced and the shelf life of food, grain and fruits andvegetables can be judged.Details:Display:6 bit backlight LCD digital display (3 bit humidity aw,3 bit temperature display)Range:0~1.0awResolution:±0.01awAccuracy:±0.02awSensor:Non conductive humidity sensorSampling Time:5 MinutesOperation Conditions:Temperature:0~50oCHumidity:<95%RHPower Supply:2x1.5V AAA Size(UM-4)BatteryDimensions:135x70x44mmWeight(Not Including Batteries):100gStandard Accessories:Main UnitSample PlateCarrying Case(B04)ManualOptional Accessories:USB Data Cable with SoftwareBluetooth Data Adapter with SoftwareIf any questions please feel free to contact Lisa Li.Thank you!
-
Product
Dynamic Balancing
-
Balancing machines of the VibroDAQ series are professional sets of tools for measuring vibrations and dynamic balancing of rotating elements in own bearings and on specialized stands.These devices are used in various industries, car workshops, repair services, and departments dealing with maintenance in various types of companies. Our balancers have also been used in scientific institutions and universities as systems for conducting research and training future engineering staff. Our devices have implemented special algorithms for balancing the grinding wheels, allowing for balancing the grinding wheels directly on the grinder.
-
Product
Coupling Decoupling Network
TBCDN-M1
-
The TBCDN-M1 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
Product
FPP Software
Four Point Probe
-
Materials Development Corporation
For use with a manual four point prober, the MDC FPP Software operates in a convenient, single screen that displays both measurement parameters and testresults. The FPP software can measure Resistivity, Conductivity, Resistance, Doping, Thickness, and SheetResistance when used with a compatible current source and voltmeter or SMU.
-
Product
9 kHz Highpass Filter
TBHPF1-9KHZ
-
9 kHz Highpass Filter for protection of spectrum analyzer or EMI-receiver RF inputs against high amplitude subharmonics and residual 50 Hz voltage in conducted emission measurement set ups
-
Product
Open Frame 6U 34HP Chassis
-
An open-frame solution for the open-minded engineer. With moveable rear profiles (up to 2.5mm,) 3U and 6U backplane compatibility options, air or conduction cooling options and the ease of fast and simple backplane interchangeability for fluid transition between VITA and PICMG bus architectures, the Hartmann Open Frame Chassis solution is the tool for customers who need versatility, accessibility and longevity.
-
Product
PRO High Range Conductivity Meter
MW302
-
MW302 is a Portable Conductivity High Range (EC) Meter with Automatic Temperature Compensation. This instrument has been designed to meet the Grower's need for equipment suited to the aggressive environments found in agricultural and hydroponics applications. It is also a great meter for food, labs, and water treatment applications.
-
Product
Meter With 4-Cell Conductivity/ATC Probe
CON 2700
-
Featuring auto-standardization, auto-calibration and auto-ranging capabilities, the Eutech CON 2700 accepts 2-cell and 4-cell electrodes, allowing a broad range of measurement at up to ±1 % full scale accuracy. Meter comes with a multi data screen that shows Conductivity readings, temperature, electrode status, calibration points, date and time all at once.
-
Product
79W to 153W - Single Output
CUS200LD Series
-
*Convection or Conduction Cooled*Up to 206W Peak Power Capability*Low 31mm Height*-40°C Ambient temperature start up
-
Product
Breakdown Voltage Tester
ZDS-50B
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.11-2008Used to test the breakdown voltage performance under room temperature of enameled round and flat wires with nominal conductor diameter of 0.018mm and above;Three voltage rise speeds are available: 20V/s, 100V/s and 500V/s, with error being ±5%;Three test methods can be adopted: round bar method, twist pair method and ball method;Clamp a group of test samples (5 for each) once, available to complete breakdown or withstand voltage test for any of sample one by one or individually; breakdown voltage and withstand voltage time would be automatically saved for future enquiry; all operations would be automatically completed;Capable of conducting high temperature breakdown voltage test in combination with RDS-50 thermal-state voltage tester;LED would automatically display test results and automatically return;During sample breakdown, breakdown voltage indication value would be automatically locked, free from flashing, and the test result is distinct and relatively clear;Equipped with test fixture for round rod method and twist pair method as well as the test weight for round rod method;Equipped with ball method test device (steel balls are prepared by user);Test door is provided with safety interlocking device, compliant with relevant regulations on high voltage testing equipment.
