Insertion Loss & Return Loss
-
Product
Micro Coax/Micro Power, Module Insert, ITA, i2 MX, 15 Position
510144009
ITA Module Insert
Micro Coax/Micro Power, Module Insert, ITA, i2 MX, 15 Position.
-
Product
PXI/PXIe Fault Insertion Switch, 64-Chan 2A, N/C Through Relays, Fault Buses on M & U
42-190C-112
Fault Insertion Unit
The 40-190C-112 (PXI) and 42-190C-112 (PXIe) are fault insertion switches with 64 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 8 Channel
50-200-008
Fault Insertion Unit
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
Product
48-Ch 2A-250VAC 2-Bus Fault Insertion
YAV90076
Fault Insertion Unit
48 channels2A 250V 2 Fault Insertion BusesSwitching up to 60CAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available
-
Product
Loss Tangent M in Dielectric Oil
TAND220A
-
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
Product
Entry Level Loss Tester
Model：OLT-20
-
OLT-20 Optical Loss Tester integrates laser source module and power meter module in one set, which can perform power testing and link loss testing in optic fiber network conveniently. The typical applications include fiber identification, attenuation and loss measurement, continuity verification and fiber link transmission quality evaluation for installation, routine inspection and daily maintenance of MAN, WAN and CATV systems as well as for lab test and research work.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 4 Channel
40-201-004
Fault Insertion Unit
This high bandwidth differential fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Flow Detector with Pressure Loss Compensation Function
FP-213S / FP-2140S
-
The Volumetric Flow Detector FP-213S, FP-2140S are volumetric flow detectors, used in combination with the Digital Flow Meter FM/DF series, for precision measurement of fuel flow such as gasoline, light oil and kerosene.They are suitable for those who want to evaluate the engine performance by measuring the minute flow rate of a small engine and making the fuel supply pressure as close as possible to the actual vehicle state.
-
Product
Signal, Insert, ITA, QuadraPaddle, SIM, Pass-Thru, 4 Pos, 1 Slot
510181105
SIM Insert
Signal, Insert, ITA, QuadraPaddle, SIM, Pass-Thru, 4 Pos, 1 Slot.
-
Product
PXI Dual Bus 64-Chan 2A Fault Insertion Switch
40-190B-102
Fault Insertion Unit
The Dual Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Quad Optical Loss Test Set
KI27624-INGAAS-APC
-
A Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber with an APC connector at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful solution to improve test flexibility and productivity.
-
Product
Signal, Insert, Receiver, QuadraPaddle, SIM, Pass-Thru, 4 Pos, 1 Slot
510180105
SIM Insert
Signal, Insert, Receiver, QuadraPaddle, SIM, Pass-Thru, 4 Pos, 1 Slot.
-
Product
PXI Single Bus 74-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-301
Fault Insertion Unit
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
RETURN PATH SIGNAL GENERATOR
TG-1215
-
Circuit Method : Individual or Simultaneously. Frequency : 20/30/40/50/60MHz(5carriers). LOW BATTERY CONSUMPTION. COMPACT SIZE DESIGN. OUTPUT LEVEL ADJUSTABLE. OUTPUT LEVEL DISPLAY. MAX. 5CARRIES(individual or Simultaneously). PORTABLE TYPE(weight less than 500g). APPLICATIONS: Testing and aligning CATV return band. Testing and adjusting Internet return band.
-
Product
Low Loss Combiners
-
*Tunable or band specific low loss combining of Tx and Rx*Typical 0.7dB insertion loss*Optional second duplexer can be installed in the same tray*High power handling with low IM and insertion loss*AISG 2.0 compliant
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A
40-194A-001
Fault Insertion Unit
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
Tool, Insertion, Vertical VTAC, VTAC SIM Modules
910112133
Insert Tool
Insertion tool for Vertical VTAC inserts. Tool layout is designed for use with 90 Series VTAC SIM Modules.
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A, Hardware Interlock
40-194A-002-HI
Fault Insertion Unit
The 40-194A-002 is a 7-Channel Fault Insertion switch with hardware interlock and two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
Loss Test Sets
-
These instruments combine up to 6 sources, a power meter & optional VFL in one unit.
-
Product
Tray Return Systems
-
Rapiscan® Systems range of Tray Return Systems (TRS™) are designed to allow for increased throughput, reduction in staff tray handling and the ability to increase passenger focus amongst various other benefits at security checkpoints.
-
Product
Combo Test Lead Kit
U8201A
Insert Kit
Designed for use with U3606A DMM | DC power supply; includes leads, probes, alligator clips, SMT grabbers, and banana plugs
-
Product
Duplex Double Test Insertion/Return Loss Test Station
JW8302
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW8302 Duplex double test Insertion/Return Loss Test Station is a professional equipment to test CWDM device, multi-wavelength device, PLC, fiber optical patch cord and other passive optical devices. It is a new-generation precision optical instrument of JOINWIT who combined with so many years experience in optical passive detection. It equipped with VFL or 850 light source , supporting threshold determination, automatic multi-wavelength detection, system integration, secondary development, upper computer solution, etc. Double LC interface or other different interfaces can be tested simultaneously which is convenient for testing and improves efficiency; The VFL function could automatic on and off, no need to replace the connector.
-
Product
Optical Loss Testing
-
Is to inject a known level of light in one end and measure the level of light at the other end, using an OLTS. The difference between source and receive power levels is the loss.
-
Product
Core Loss Tester
VCL
-
Core loss testing has become most important test for quality assurance in Electrical industry. Core loss tester determines that whether a Core is damaged or not.
-
Product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
Fault Insertion Unit
The 40-205-008 (PXI) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
PXI Single Bus 64-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-401
Fault Insertion Unit
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Dual Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-202
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A, Hardware Interlock
40-193A-002-HI
Fault Insertion Unit
The 40-193A-002-HI is a 7-Channel Fault Insertion switch with hardware interlock and two fault buses, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
Product
Micro Power or Micro Coax, Insert, Receiver, SIM, 2 Pos, 2 Slot (not loaded)
510180104
SIM Insert
Not loaded. Micro Power or Micro Coax patchcords need to be purchased separately.
