-
Product
Split type Pulse Current Sensor
CTF-05T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For detecting current pulse with open collector output (for power pulse)
-
Product
sbRIO-9253, Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module
787433-01
Current Input Module
Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module - The sbRIO-9253 is an 8-channel analog input module for CompactRIO Single-Board Controller that provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. This module includes diagnostic functionalities to ensure nominal system operations with open-channel detection, power supply detection, and configurable thresholds. You can view the status of each channel and the power supply with eight LEDs. The sbRIO-9253 also features programmable hardware filters for your applications, such as specific Butterworth and comb filters that you can use to reduce the noise in your system.
-
Product
Optical OTDR
TLM-02D
-
Hangzhou Tuolima Network Technologies Co., Ltd.
OTDR-02D series Optical Time Domain Reflectometer (OTDR) is an intelligent meter of a new generation for the detection of fiber communications systems. With the popularization of optical network construction in cities and countrysides, the measurement of optical network becomes short and disperse; OTDR-02D is specially designed for that kind of application. It’s economic, having outstanding performance.
-
Product
Accelerometers
-
Accelerometers measure linear acceleration. They can be also used for specific purposes such as inclination and vibration measurement. MEMS accelerometers embed several useful features for motion and acceleration detection, including free-fall, wakeup, single/double-tap recognition, activity/inactivity detection and 6D/4D orientation.
-
Product
Ignition Pulse Detector
IP-3100
-
The IP-3100 enables ignition pulse detection of gasoline engines with high sensitivity. The rotation speed can be easily measured by clamping the primary side cord (low voltage), the secondary side cord (high voltage), and current cable of the electronic distributor. The IP-3100 is used with the tachometer made by Ono Sokki.
-
Product
Light Section Sensors
-
Leuze electronic GmbH + Co. KG
Switching light section sensors are designed to perform scanning, two-dimensional object detection along a laser line. They are especially well suited for completeness monitoring or product monitoring in the case of multiple track transport. The short measurement time and the detection range from 200 to 800 mm enable an inspection of the content at a high throughput rate even with deep containers. The internal data processing offers programming and differentiation of 16 different object types, thereby conserving control capacity. Complex detection tasks can be solved with one sensor. The compact housing ensures high flexibility during installation and saves installation space.
-
Product
Metal Detection
-
The Elcometer Metal Detection range includes Valve Box Locators that are rugged and simple to use making them the ideal choice for all location work in all types of terrain.
-
Product
90-Degree Optical Hybrid
-
Six-port hybrid devices have been used for microwave and millimeter-wave detection systems since the mid-1990s and are a key component for coherent receivers. In principle, the six-port device consists of linear dividers and combiners interconnected in such a way that four different vectorial additions of a reference signal (LO) and the signal to be detected are obtained. The levels of the four output signals are detected by balanced receivers. By applying suitable baseband signal processing algorithms, the amplitude and phase of the unknown signal can be determined.
-
Product
Substrate Manufacturing
-
KLA’s substrate manufacturing portfolio includes defect inspection and review, metrology and data management systems that help substrate manufacturers manage quality throughout the wafer fabrication process. Specialized wafer inspection and review tools assess wafer surface quality and detect, count and bin defects during production and as a critical part of outgoing wafer qualification. Wafer geometry systems ensure the wafer shape is extremely flat and uniform in thickness, with precisely controlled wafer shape topography. Data analysis and management systems proactively identify substrate fabrication process excursions that can lead to yield loss. KLA’s substrate manufacturing systems support process development, production monitoring and final quality check of a broad range of substrate types and sizes including silicon, prime silicon, SOI, sapphire, glass, GaAs, SiC, GaN, InP, GaSb, Ge, LiTaO3, LiNBO3, and epitaxial wafers.
-
Product
Alignment Sensors and Switches
-
The Touchswitch is an electro-mechanical limit switch with no moving parts, which detects tracking and misalignment problems on bucket elevators and conveyors. When a belt misaligns or a pulley moves over and contacts the sensor, the built in solid-state electronic circuitry detects the lateral force of the belt or pulley and activates a voltage free relay contact. This relay contact is used to immediately alarm and shutdown the machine.
-
Product
Thermometer Hygrometer Barometer
H7530
-
Sensor H7530 is designed for online monitoring of temperature, relative humidity of air without aggressive substances. Three binary inputs to detection of two-states signals are the advantage. Other devices are controlled by two relay outputs.
-
Product
Day/Night IP Surveillance Camera
ENVIROMUX-IPCAM-N
-
View and control the camera from the ENVIROMUX web interface, the camera web interface, included software, or with a compatible cell phone. With the ENVIROMUX-2D/5D/16D, a triggered snapshot can be forwarded in alert e-mails. A snapshot can be triggered by any programmed event (motion detection, door open/close, glass break, smoke, liquid detection, etc.). Image sensor: 1/4" progressive scan CMOS sensor. Video Streaming: simultaneous Motion JPEG and MPEG-4. Frame rate: 30fps at 640x480 (VGA) resolution. Lens: F2.0, 4.3 mm (0.17 in), 12 infrared LEDs for night vision. RJ45 connector. Wireless models: wireless IEEE 802.11 b/g up to 54 Mbps. Regulatory approvals: CE, FCC, RoHS.
-
Product
Leak Detect Stik Liquid Level Sensor
7100
-
The 7100 leak detect stik is a liquid level sensor that takes field proven magnetostrictive sensing technology and packages it in a revolutionary new way for greater reliability and for easy installation and mounting.The 7100 leak detect stik has PPM (Pulse Position Modulated) outputs for product and interface level and for temperature measurement, which are all superimposed on the two wire power line.All sensor electronics used in this liquid level sensor are SMT components integrated into the 5/8” diameter sensing tube. This breakthrough in package design eliminates the bulky electronics enclosure at the top of the sensor and offers you greater options for insertion.
-
Product
Gas Monitor System
-
Henan Bosean Electronic CO.,Ltd.
Used to detect combustible, flammable and toxic gases, and oxygen depletion.
-
Product
Automatic High Voltage Wire Harness Testers
-
Automatic high voltage wire harness testers are used in a variety of industries, such as aerospace and defence through to rail, and are used to test any equipment which contains a high number of electrical wires, or active components ensuring these pass specified test criteria at the sub-assembly and final stages of construction. These systems ensure the wiring and components are 100% compliant and undamaged, recording every test measurement and aiding diagnosis of detected faults.
-
Product
Rotational Flow Demonstration Kit
-
The rotational flow demonstration kit detects the rotational position using the MCU’s on board data transfer controller (DTC) function, a form of state machine, while the MCU’s core is in stop-mode state. This ensures that the average power consumption is kept as low as possible, with IAV (average current) at 4.5 microampere (μA) and a 32 sample burst per second. The flow demonstration kit senses the flow direction and volumetric flow rate of water and gas, and can also detect reverse flow. The demonstration kit is applied using an active inductive method. Two coils are used to sense the rotational position of a part-metalized disk, and a third coil is used to generate a reference signal.
-
Product
Motion Magnification Software
Dragon Vision
-
Incredible as it may seem, machine and structural vibration (or at least a large part of it) can be detected in a video recording with incredible resolution. Our unique video analysis algorithms make it possible to detect micro-movements and convert these movements into thousands of reliable vibration signals from just one video. In addition, with our software it is possible to perform motion magnification, making it possible to visualize vibration in ways that the human eye can’t see.
-
Product
Receptacle Tester
RT500
-
Designed to detect the most common wiring problems in standard 120V receptacles.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.Made in USA of U.S. and imported parts.
-
Product
Fire, Gas & Intruder Controllers & Alarms
MultiSafe-MX
-
Teledyne Gas & Flame Detection
The MultiSafe-MX system is intended for the protection of high hazard, high risk plant and facilities.The MultiSafe-MX is certified, by European laboratories, to comply with the applicable regulations.The panel is composed of dedicated cards, installed in 19” racks which have their own “intelligence”, programmed for active/passive fire protection, gas detection, intruder alarm and logic functions. Moreover, the MultiSafe-MX can interact with supervisory and SCADA systems via Ethernet, TCP/IP or Modbus.The MultiSafe-MX interfaces with devices using either conventional and/or addressable module inputs and outputs. These modules are used to tailor the system to customer requirements.
-
Product
Thermal Imagers & Industrial Endoscopes
-
GAOTek has developed advanced thermal imagers that are high quality, affordable, and accurate. Thermal imager is a non-contact temperature measurement device. It detects the infrared energy transmitted, reflected or emitted by all materials at a temperature above absolute zero. The energy factor is converted into a temperature reading or thermogram. Thermogram is the thermal image radiation produced that is displayed by the camera object emitting infrared energy. Thermal imagers are widely used for finding potential problems in applications across disciplines.
-
Product
Temperature Rise Tester
WS-1
-
Applied to test electrical accessories heating conditions when connected to load current, whether the temperature rise of electrode is compliance with standard requirement or not. And it can effectively detect whether the plug bush is slants thin and whether plug and socket cooperated with all right. It is designed and manufactured according to IEC884－1, GB2099.1-2008 and other relevant standard of electrical accessories.
-
Product
Digitally Controlled Ultrasonic Detector
VPE-1000
-
he VPE-1000 is perfect for schools, hospitals, hotels, and other large institutional or industrial environments. Use for a variety of leak detection and plant maintenance applications
-
Product
Dual-Sensor Temperature-Measurement Pan/Tilt
TRITON™ A310 PT (Security)
-
Security professionals around the world have been using FLIR thermal cameras for perimeter and critical asset security for years. Facility Operations and Safety personnel have been using FLIR cameras to gather non-contact temperature measurements and condition monitoring data for decades. A310F and A310PT cameras are the first in the world to combine thermal and visible light video security imaging with automated safety monitoring based on the detection of temperature measurement thresholds.
-
Product
Fiber Microscope
WL-C400S
-
The WL-C series fiber microscopes use coaxial illumination to provide users with maximum detail. It easily can detect the finest scratches and contamination, making it ideal for critically inspecting polish quality.
-
Product
Electric Safety Wall Detection Test Mode
-
AllWin Instrument Science and Technology Co., Ltd.
Electric safety wall detecting functionTest mode programmableACW to IR function toggle automatically
-
Product
Thermal Analytics Security Camera
Elara™ FB-Series ID
-
The FLIR Elara™ FB-Series ID thermal security camera uses onboard analytics to classify human or vehicular intrusions, making it ideal for perimeter intrusion detection and sterile-zone monitoring. The Elara™ FB-Series ID can also hand off classified intrusions to FLIR PTZ cameras for autonomous tracking of intruders. Easy to set up, Elara™ FB-Series provide reliable detection with low false alarm rates in challenging environments, bad weather, and complete darkness.
-
Product
Quantum-Safe Security
CN6000 Series
-
The Centauris CN6000 encryptors may be upgraded to quantum cryptography through the addition of the Cerberis Quantum Key Distribution (QKD) server to ensure that the solutions are quantum-safe for the long-term protection of sensitive data. This also ensures investment-protection of the encryptors. Such quantum cryptography is provably secure, ensures anti-eavesdropping detection and provides long-term forward secrecy against brute force hacking and attacks by quantum computers.
-
Product
Confocal FLIM for Macroscopic Objects
DCS-120 Macro
-
*FLIM of Macroscopic Objects*Scan Field Up to 15 mm Diameter*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Scanning by Fast Galvanometer Mirrors*Channel Seperation by Dichroic or Polarising Beamsplitters*Individually Selectable Pinholes and Filters*One or Two BDL-SMN or BDS-SM ps Diode Lasers*Tuneable Excitation by Super-Continuum Laser with AOTF*Two Fully Parallel Detection Channels*Two HPM-100-40 GaAsP Hybrid Detectors*Optional: Two HPM-100-06 Hybrid Detectors, IRF Width < 20 ps FWHM*Optional: HPM-100-50 Hybrid Detectors for NIR FLIM*Optional: Multi-Wavelength FLIM*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Simultaneous FLIM/PLIM*Wideband Version, Compatible with Tuneable Lasers*Electronic Pinhole Alignment*Optional: Spatial Mosaic FLIM via Motorized Sample Stage
-
Product
Air Quality Meters
-
An indoor air quality meter is used in confined spaces to prevent mold, to monitor CO2 levels, or to detect gas leaks. Whether portable or fixed, handheld or wall mounted, air quality monitoring equipment is essential for ensuring health and safety. At PCE Instruments, you will find air quality monitoring devices that meet various industry standards relating to personal safety and that are used to detect, measure and monitor relative humidity, ambient temperature and / or levels of carbon dioxide (CO2), volatile organic compounds (VOCs), formaldehyde (HCHO), freon and other refrigerants (CFC / HFC), phosphine (PH3), hydrogen sulphide (H2S), carbon monoxide (CO), nitrogen dioxide (NO2), oxygen (O2), ozone (O3) and other flammable, hazardous or toxic gases.
-
Product
Position / Distance / Proximity Sensors
-
Panasonic Industrial Devices Sales Company of America
Easy-to-use Inductive Proximity Sensors provide stable detection for automation, with Sensors for standard to high speed, high performance solutions. These Inductive Proximity Sensors detect the presence and position of ferrous and non-ferrous metal objects and come in a range of IP Ratings (IP50 / 67 / 68 / 68g). The IP68g enclosure allows usage in very harsh environments. For high speed, high accuracy measurement, Laser Measurement Sensors are ideal for the precise measurement of thickness, diameter and height. Panasonic’s HG-C Series CMOS Type Micro Laser Distance Sensors deliver high repeatability for measurement distances (center) of 30mm, 50mm, 100mm, 200mm and 400mm. Ideal to measure insertion depths or thickness, these Sensors can also be used to detect warping, overlaps and presence helpful for preventative maintenance and remote monitoring. Select models are IO-Link compatible for ease of use.
