Drivers
translate general instructions into hardware specfic commands.
-
Product
PXIe-4340, PXI Displacement Input Module
785068-01
Displacement Input
The PXI Displacement Input Module supports 4-, 5-, and 6-wire AC linear variable differential transformer (LVDT) and AC rotary variable differential transformer (RVDT) measurements. The module simultaneously samples each analog input and sets the excitation frequency and voltage for each channel independently. You can set different timing, triggering, and sampling modes for each channel independently. Diagnostic features include self-calibration, overcurrent detection, and open coil detection.The PXI Displacement Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Primus Epic Interface Kit
LANTAP-10
-
Innovative Control Systems, Inc.
*LANTAP-10 kit comes with 10’ Coaxial cable, 6’ USB cable, 6’ CAT5 cable, BNC Connector and Terminator.*Allows connection of any 10/100/1000 Ethernet equipped system to EPIC equipped *Aircraft LAN or ANY 10base2 need.*No drivers to install. The LANTAP is NOT a USB device. It is only powered by USB.*Complies to IEEE 802.3 10Base-T and 10Base2*LED diagnostics and monitoring indicators
-
Product
PXIe-6365, 144 AI (16-Bit, 2 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
783633-01
Multifunction I/O
PXIe, 144 AI (16-Bit, 2 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6365 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6365 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Switch Drivers
-
Macom Technology Solutions Holdings Inc.
MACOM’s switch drivers bridge the gap between digital control signals and the analog voltages and currents required to drive our extensive family of RF, microwave and millimeter wave PIN diode and FET switches.
-
Product
IVI Driver Package
IVI Development
-
The most complete IVI driver package from the most trusted name in IVI. Driver development can be tedious and distracting when you are scrambling to meet product deadlines. Researching the latest IVI standards, lack of driver documentation, and changing firmware all work against your product deadline. As a result, quality control over your product or driver or both can suffer. With IVI Development services from Pacific MindWorks you are free to focus on your product.
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785959-01
FlexRio Digitizer
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
16 Channel USB Sensor Interface
RogaDAQ16
-
With the introduction of the RogaDAQ16 USB 2.0 data acquisition system, a new age of measurement technology begins.*USB 2.0 / 480MBIT (USB1.1/12MBIT COMPATIBLE)*16 analog input channels (16bit/500kHz max.)*ICP ® ( IEPE ) sensor supply (24V/4mA)*0.125V to 10V input range*Individual preamplifiers*4 analog output channels (16bit/100kHz)*Powerful DSP (255MIPS) for filtering, control etc.*24 digital I/Os*Optional 24bit counter, timer, PWM, incremental encoder*Free drivers for major application software*including DASYLab; LabView & DiaDem drivers & RogaRec Software
-
Product
The World's Most Advanced Integrated Thermal Traffic Detector
TrafiSense2
-
TrafiSense2 is an integrated thermal sensor and detector for vehicle, vulnerable road user, and wrong way driver detection. TrafiSense2 does not need light to operate, and instead uses the thermal energy emitted from road users. This enables the sensor to detect vehicles and vulnerable road users at night, over long distances, and in harsh weather conditions. With available 640x480 resolution, the TrafiSense2 offers 24/7 traffic detection for a wide range of applications.
-
Product
AFDX ® / ARINC 664 Test And Simulation PXI Module
PXI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Stard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applicationsWindows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
SD Card V.4.1 & UHS-II PHY
SD 4.1 Total Solution
-
To meet the ever increasing data transfer rate in high end applications, such as professional broadcasting transmission or advanced high resolution display, the SD 4.1 specification calls out the maximum performance of 1.56 Gbps at UHS-II full duplex mode per lane or half duplex UHS-II at 3.16 Gbps. In real applications, due to the system overhead and different SD 4.1 device controller designs, the actual measured performance can vary dramatically from system to system. With the newly introduced ADMA 3, the OS driver is now able to issue multiple read or multiple write commands at once, without having to wait for the SD controller to complete one command at a time. Once the SD host controller has collected multiple commands, it will then manage and complete them without intervention from the host software drive. Thus, the UHS-II 1.56 Gbps interface can be more effectively utilized and maximize the system throughput. This feature can be very useful when running multithreaded applications where multiple applications are constantly updating their status or swapping their contents by writing or reading small chunk of data to or from the memory card.
-
Product
PCIe-8361 , x1 Gen1 PCI Express Host, 208 MB/s, 1-Port, Copper Cable MXI-Express Device for PXI Remote Control
779504-01
Remote Control Interface
The PCIe‑8361 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI Express slot. The PCIe‑8361 remote controller provides a x1 PCI Express link over a copper cable to the PXIe‑8360 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
PCI - Quad Industry Pack Carrier w/ DSP
PCI-4IPM
-
The PCI-4IPM module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the PCI-4IPM is the perfect solution.The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via thePCI bus. WinNT drivers are standard.
-
Product
GPIB-RS232, Instrument Control Device - United Kingdom 240VAC
779732-06
GPIB Controller
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
3U CompactPCI Serial Front Removable SATA Carrier for SSDs
SD8-STEEL
-
The SD8-STEEL is a peripheral slot card for CompactPCI® Serial systems. It includes a shuttle for 1.8 or 2.5” SSD or HDD drives. Signal integrity is optimized with 6Gbps SATA drivers. A push button ejection of the drive enables easy swap removal.
-
Product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
APCI-3120-16-4
-
*Optical isolation 500 V*16 SE or 8 diff. inputs*Data transfer rate: 100 kHz*16-bit resolution*4 analog output channels*Data transfer rate:30 kHz*14-bit resolution*Output voltage: 0-10 V, ±10 V, (set through software)*Each output has its own ground line*Driver capacity: 5 mA/500 pF*Short-circuit protection: EMI filters*Data exchange through 16-bit I/O digital*4 digital inputs*and 4 digital outputs, 24 V , opto-isolated
-
Product
PXIe Embedded Controller Factory Configuration Service
43-920-WIN
-
Our PXIe Embedded Controller Factory Configuration Service includes a Windows 10 license and driver installation on our PXIe Embedded Controllers. The service includes Windows and Pickering drivers/NI VISA/Pickering chassis management drivers pre-installed, so you can set up Windows as if it were any new PC (it will guide you through account creation, localization, personalization etc.).
-
Product
Ion Chromatography
Metrohm IC Driver 2.1 for Empower®
-
Software drivers for integrating Metrohm IC instruments in "Empower® 3" made by Waters. One license per computer authorizes the operation of IC systems under "Empower® 3".
-
Product
PXI Software
-
Keysight modular products include software tools to help you quickly access your test equipment and make measurements. The Keysight IO Libraries Suite allows you to display and configure all of the modules in your system such as LXI, VXI, PXI, AXIe and USB. In addition, software drivers support the most common programming environments such as Visual Studio, C, C++, Visual Basic, MATLAB and LabVIEW.
-
Product
cRIO-9058, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller
787880-01
Controller
1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9058 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with LabVIEW. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-01
Multifunction I/O
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
ADLINK PXI Platform Services (APPS)
Platform
Software framework services and drivers fully support PXI-2 and PXI-6 software specifications
-
Product
Driver Vision Enhancement System for Today’s Vehicles
PathFindIR™ II
-
PathFindIR II is a powerful thermal night vision system that helps you clearly see road hazards in total darkness, and it will alert you to nearby vehicles, people, and animals. Headlights typically illuminate about 450 feet straight ahead, but PathFindIR II detects heat without a need for light, allowing you to see up to four times farther down the road. You’ll have visibility through dust, smoke, or fog, and better capability to avoid an accident.
-
Product
Super Fast Universal ISP Programmer
48Pro2C
-
The Dataman 48Pro2C is a super fast PC based universal 48-pin programmer with ISP capabilities and USB 2.0 connectivity • Up to 75% faster programming of high-capacity memory devices • Over 104,000 devices supported with new devices added monthly • Intelligent pin drivers operate down to 1.8V so you'll be ready to program the full range of advanced low-voltage devices • Full ISP capabilities including JTAG compatibility • Hi-speed USB 2.0 connectivity • Easy to use software compatible with the latest operating systems including Windows 10 • Multiprogramming support allows one PC to control up to four units programming independently or as a gang programmer • Comprehensive 3 years parts and labor warranty • Free life-time software updates
-
Product
Advanced Driver Assistance Systems (ADAS) Testing
-
Advanced Driver Assistance Systems (ADAS) TestingAll modern vehicles are now being equipped with Advanced Driver Assistance Systems (ADAS). The development of such systems requires complex testing, including the ability to control and calculate relative positions between multiple vehicles and objects in real-time. We provide an effective solution for ADAS testing with highly accurate GPS positioning systems to measure relative positions and velocity between multiple vehicles and objects.
-
Product
PXI Digital I/O Modules
-
Pickering's PXI Digital I/O Modules are suitable for operating external devices or for interfacing with external logic. Two choices of output drivers are available:*TTL for interacting with external logic*Output channels for operating external devices with voltages to 60VDC and current to 2A
-
Product
Digital Input Board, 16 Isolated Channels, 24V
APCI-1016
-
*16 digital inputs, 24 V Optical isolation 1000 V Input filter*Protection against pole reversal*Standard drivers for:*Real time drivers for Windows 2000/NT/98.*The board is supplied with the universal software ADDIPACK.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-400B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Conduction Cooled Interface Board Supporting up to 5 Multi Function Channels
EXC-1553PMC/Px(S) / EXC-1553ccPMC/Px(S)
-
MIL-STD-1553, conduction cooled, interface board. Supports up to 4 multi function channels.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are multi-channel (up to four) MIL-STD-1553 interface boards for PCI Mezzanine Card compatible computers.Multi Function:Each channel operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. In addition, error injection (BC and RT modes) and error detection (all modes) are supported on each channel.Single Function:Each channel operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: PxS is NOT compatible to the MCH family of cards.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are supplied with C drivers, including source code, and Merlin+ Windows software.
-
Product
PC/104-GPIB, ISA GPIB Instrument Control Device
778041-02
GPIB Controller
ISA GPIB Instrument Control Device - The PC/104-GPIB is a plug-and-play IEEE 488 interface for industrial environments. The PC/104-GPIB performs the basic IEEE 488 Talker, Listener, and Controller functions required by the IEEE 488.2 standard. The PC/104-GPIB includes a license for the NI-488.2 driver software, which provides high performance and maximum reliability for connecting to third-party instruments using GPIB. The PC/104-GPIB is software- and register-compatible with the AT-GPIB/TNT.
-
Product
J-Type Thermocouples Wire, Fiberglass (32 deg F to 900 deg F) 2 m
745690-J002
Thermocouple Contact (ITA)
J-Type Thermocouple, 32°F to 900°F Temperature Sensor - The J-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the J-Type Thermocouple and acquire synchronized temperature data in units of degrees. The J-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
