Drivers
translate general instructions into hardware specfic commands.
-
Product
PXI 64 Channel Relay Driver Module
40-411-001
Relay Driver
The 40-411 is the perfect solution for driving external relays from a PXI system or from Pickering Interfaces LXI modular chassis. Each module provides 64 channels of low side switching for external relays. Users need to simply connect a positive voltage source to one side of the relay coil and the other side to the 40-411 output. Each output is capable of sinking up to 1 Amp of continuous current.
-
Product
PCI Bus Analog Output Board, 8 Isolated Outputs, 14 Bit
APCI-3501-8
-
*8 analog output channels*Optical isolation 500 V*Settling time 30 µs typ.*14-bit resolution (13 bit for 0-10 V)*Output voltage: ±10 V, 0-10 V (switchable through software)*Output voltage after reset: 0 V*Each output channel has its own ground line (without optical isolation from the others)*Driver capacity: 5 mA/500 pF*Short-circuit protection, EMI filters*Noise neutralization of the PC supply*Creeping distance: 3.2 mm acc. to DIN VDE 0411-100*Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary*2 digital input channels, 24 V, isolated*2 digital output channels, 24 V, isolated
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
CAN Interface
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
PXIe-4302, 24-Bit, 32-Channel, 5 kS/s, ±10 V PXI Analog Input Module
783865-01
Analog Input Module
24-Bit, 32-Channel, 5 kS/s, ±10 V PXI Analog Input Module—The PXIe‑4302 is a filtered input module for voltage, thermocouple, and current measurements. The module has an A/D converter per channel to enable a simultaneous sample rate of 5 kS/s. The PXIe‑4302 offers you the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
Product
USB-8486, USB, 1-Port, Fieldbus Interface Device
781160-02
Interface Module
The USB‑8486 is a FOUNDATION fieldbus device for developing applications with the NI‑FBUS driver, NI‑FBUS Configurator, and NI‑FBUS Monitor. FOUNDATION fieldbus is a popular industrial communication standard for process control applications. The NI‑FBUS Configurator features user-friendly multi-window interfaces to provide tools for the complete configuration, programming, and execution schedules of FOUNDATION fieldbus segments. The NI‑FBUS Monitor is a stand-alone application used to monitor, debug, and analyze fieldbus data packets.
-
Product
Analog I/O module with 32/16 multiplexed analog input channels
IO102
-
Fast 16-bit analog module with 32/16 multiplexed analog input channels and 4 analog output channels. This I/O module offers lower input sampling and conversion times than the IO101 and therefore leads to smaller overall driver latency time. It is similarly priced as the IO101 but comes with 4 analog outputs instead of 8.
-
Product
Chassis - Controls up to 16 Switch Modules in 16x8, 32x4, or Dual 16x4 Configurations
CXB/128-MF
Chassis
These Chassis controls up to 16 switch modules in 16x8, 32x4 or dual 16x4 configurations. Available as single pole systems with the outer conductor of the BNC taken to ground, or isolated 2 pole systems switching both center conductor and ground. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
Product
PXI Flexible Microwave Module, Dual SP6T Terminated 26.5 GHz, Single SPDT 26.5 GHz, 50 Ω, SMA
40-890-004
Switch Module
The 40-890 (PXI) and 42-890 (PXIe) range of PXI microwave modules allows users to specify the mix of relay types, frequencies and quantities based on the application requirements within the capabilities of the module driver card. Choose from the extensive relay selection already available in the Pickering microwave range to create a flexible solution.
-
Product
CB Radios
-
Offers professional drivers a legal way to communicate safely and easily on their smartphone with the Patented CB Radio with Bluetooth®Wireless Technology and enhanced Smartphone Features .
-
Product
Windows Driver & SDK for ADLINK USB DAQ Series Data Acquisition Modules
UD-DASK
Data Acquisition Module
ADLINK DASK drivers are the device drivers for custom data acquisition applications for Windows. The DASK driver libraries provide API sets for ADLINK PCI ExpressR, PCI, CompactPCI, PXI and USB data acquisition cards, to access full hardware functionalities, such as buffered/double-buffered data acquisition, pattern generation, digital input/output and etc. For novice users, the built-in CodeCreator utility helps you create your first program in just a few minutes.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 1.25 GS/s on 1 Channel
M4I.6630-X8
Arbitrary Waveform Generator
The M4i.66xx-x8 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PCIe cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x8 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4i series 625 MS/s AWG.
-
Product
C Series Current Output Module
Input/Output Module
The C Series Current Output Module features up to eight channels of simultaneous analog output. You can choose between enclosed and non-enclosed modules. Additionally, the C Series Current Output Module has built-in open-loop detection. This detection generates an interrupt in software when an open loop is detected, zeros outputs to ensure safety, and avoids driving actuators at system power-on. The C Series Current Output Module requires an external power supply and includes a channel-to-earth ground double isolation barrier for safety and noise immunity.The C Series Current Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Software
-
Active Silicon computer vision products are supported by a variety of software tools. We provide powerful user software and SDKs for CoaXPress and Camera Link frame grabbers with support across several operating systems. Additionally, a wide range of drivers for third-party machine vision and scientific imaging packages is available.
-
Product
Compact IEPE Sensor Interface
Plug.n.DAQ Lite
-
ROGA Instruments Plug.n.DAQ Lite is a compact IEPE sensor interface for linux or windows with 2 input channels. It offers the USB PC interface and requires no drivers for installation. The operating system such as LINUX or Windows recognizes the device as an external usb audio card.
-
Product
Industrial 4-20mA Driver
-
Analog Devices portfolio of leading industrial d/a converters and drivers addresses the challenges of enhancing system accuracy, reliability, and overall functionality while reducing form factor and power dissipation. The products provide a range of programmable output ranges from standard 4–20 mA for current loop communication to ±10 V for actuator control. They simplify industrial system design by offering considerable control functionality and advanced on-chip diagnostics to maximize system up time. ADI industrial converters also eliminate the need for costly calibration routines needed by some traditional discrete architectures.
-
Product
Synchro Power Amplifiers
SPA
Amplifier
Computer Conversions Corporation
The SPA Series "Pulsating" Synchro Power Amplifiers are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and radar/Antenna related, applications. They are commonly used on synchro based data transmission, re-transmission, simulation and instantaneous absolute position indicating and active control systems.
-
Product
PXIe-4305, 24-Bit, 32-Channel, 51.2 kS/s, 42 V, PXI Analog Input Module
783868-01
Analog Input Module
24-Bit, 32-Channel, 51.2 kS/s, 42 V, PXI Analog Input Module—The PXIe‑4305 is a filtered analog input module for higher voltage measurements. The module offers the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
Product
ARINC 429 Test & Simulation Interface for PCI
PCI-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/FilteringIRIG-B time code encoder/decoder with free-wheeling modeApplication Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Virtual Serial Port Driver
-
The main goal of Virtual Serial Port Driver by Eltima Software is creating virtual COM port pairs. Virtual serial ports created in VSPD behave as if they were real ports and are taken for the real ones with the serial applications. Via these ports serial applications can communicate with each other and transfer data via virtual null-modem cable. The data written to one virtual serial port can be instantly read from the other. Virtual serial ports created in VSPD support all serial port settings, strict baudrate emulation, HandFlow control and signal lines. After virtual COM port pair was created, one can see these ports in Device manager, moreover these ports are available automatically at system startup, even prior to logon. Virtual Serial Port Driver is available in a GUI version as well as a driver version with API for those who are going to use it in their own product.
-
Product
USB-5132, 50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device
779969-02
Oscilloscope
50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device - The USB‑5132 low-cost oscilloscope device has two channels that sample up to 50 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes and an instrument driver that includes data streaming and analysis functions. This device is ideal for portable and benchtop applications with fast signals that require flexible measurement configurations and up to 50 MHz of analog bandwidth.
-
Product
PCI-6123, 8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O Device
779408-01
Multifunction I/O
8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O Device - The PCI‑6123 is a simultaneous-sampling, multifunction DAQ device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6123 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6123 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
Shared Memory Network PCI & PCIx Interface
PCI-SMN
-
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Compatible with PCI & PCIx Host System Slots - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
Product
Intelligent Interface Card
IIB-1553-CPCI
-
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.The IIB-1553-CPCI supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes,with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface.2 Mbytes of dual ported RAM are supplied as standard. The board is supplied with C drivers in source code and Windows menu driven software.
-
Product
PXIe-5160, 500 MHz, 2.5 GS/s, 10-Bit PXI Oscilloscope
782621-12
Oscilloscope
PXIe, 500 MHz, 2.5 GS/s, 10-Bit PXI Oscilloscope—The PXIe-5160 high-speed oscilloscope device has two or four channels that sample at up to 2.5 GS/s with flexible settings for coupling, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 500 MHz of analog bandwidth and flexible measurement configurations.
-
Product
PXIe-4303 , 24-Bit, 32-Channel, 51.2 kS/s, ±10 V PXI Analog Input Module
783866-01
Analog Input Module
24-Bit, 32-Channel, 51.2 kS/s, ±10 V PXI Analog Input Module—The PXIe‑4303 is a filtered input module for voltage, thermocouple, and current measurements. The module offers you the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
Product
FMC L-Band RF Receiver
-
Sundance Multiprocessor Technology Ltd.
The Creonic L-band RF receiver FMC card allows to receive RF signals between 925 and 2,250 MHz. It is ideally suited for satellite communication with standard satellite dishes since it includes a DiSEqC driver IC for LNB controlling. The board allows to build receivers with symbol rates of up to 100 Msymbols/s. Due to the low-pin-count (LPC) FMC connector it can be used with any FMC carrier board that supports VADJ=1.8V. The card will be available from Q2/2017.
-
Product
PXI-8512, 1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-01
CAN Interface
1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
HS-1760 Flight Rated XMC Network Interface Controller
XMC-1760-NIC-CC
-
Avionics Interface Technologies
Dual Channel configurations supporting NC/NC, NC/NT, or NT/NT - 75 Ohm single ended copper or 150 Ohm differential - Eight (8) opto-isolated discrete I/O lines - Rear I/O through the P16 connector - Conduction-cooling and/or conformal coating available - x4 PCIe interface to NIC interfaces, with DMA controller for data movement - Designed for extended temperature operations - ANSI Application interface supporting C development - Device driver support: Windows, Linux, & VxWorks (others on request)
-
Product
PXI-6229, 32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module
779115-01
Multifunction I/O
32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXI‑6229 offers analog I/O, correlated digital I/O, two 32‑bit counter/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
LED Driver Online Tester
LEDLS-60/LEDLS-12
-
• The tester includes A Group Measuring Module and B Group Measuring Module. The A Group measuring module can test 6pcs LED Driver AC Parameters. The B Group measuring module can test 6pcs LED Driver AC, DC and AC/DC Parameters. • There are 12 windows to display the input and output parameters, it is good for comparing and analyses. • Quick test for all of the parameters in 0.1 seconds. • It can set up the testing parameters PASS/FAIL range, it will have Noise/Light warning if it is Fail. We also supply handle port (Extra cost) • Software communicate with PC (Extra cost)
