-
Product
4/8 Channel 20.0 ~ 56.0 Gb/s PAM4 Bit Error Rate Tester
CA9810
-
The UC INSTRUEMNTS CA9810 4/8 Channel 20.0 ~ 56.0 Gb/s PAM4 Bit Error Rate Tester is a high performance, flexible and cost effective four/eight channel PAM4 Bit Error Rate tester that can operate from 20.0 Gb/s to 56.0 Gb/s each Channel. 4/8 channel 56.0 Gb/s make it total up to over more than 240/480 Gb/s testing capacity. It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer.
-
Product
Clock Generator Module
M8008A
Clock Generator
The M8008A is designed as sample clock source for the M8199A 128/256 GSa/s Arbitrary Waveform Generator. It can also be used as a standalone low-jitter clock source for other applications. It comes as a 1-slot AXIe module, which allows the M8008A plus up to two M8199A AWG modules to be plugged into a single 5-slot AXIe chassis.
-
Product
PCI Express A/D Board
AD12-2000 - Dual 12 bit, 2 GS/s, up to 7GB/s DMA
-
The AD12-2000 series has two 2000 MS/sec 12-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at up to 7 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, at twice the effective memory depth and speed (up to 4 GSPS).
-
Product
4-Channel 200 MHz A/D with DDC, VITA 49.0, Virtex-6 FPGA - 6U VPX
Model 57664
-
- Supports Xilinx Virtex-6 LXT and SXT FPGAs- PCIe output supports VITA 49.0 VITA Radio Transport (VRT) Standard- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- One multiboard programmable beamformers- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
FMC Dual ADC 12-bit 2.6 GSPS, Single DAC 16-bit 12 GSPS
FMC250
-
The FMC250 is an FPGA Mezzanine Card (FMC+) per VITA 57.4 specification. The board has dual ADC and single DAC. The FMC250 utilizes dual AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a single DAC (AD9162 or AD9164) providing 16-bit conversion rates of up to 12 GSPS. The analog input, digital output, clock and trigger interfaces of the FMC250 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
Product
10 Channel ADC FMC Module
ADCFN10-DC – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN10 is a ten channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Both AC and DC coupled input are supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
Product
Clock And Trigger Synchronization System
CLKSYNC-40
-
CLKSYNC-40 is a clock and trigger distribution system that provides multiple, independent copies of clock and trigger signals for multi-channel, Giga-sample ADC and DAC boards. Up to sixteen independent ADC or DAC clocks and triggers are synchronized.
-
Product
8-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - 6U VPX
Model 58760
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four or eight 200 MHz 16-bit A/Ds- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Sample clock synchronization to an external system reference LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Mainframes
-
Our CompactPCI series mainframes are industry-standard, open-architecture chassis with enhancements to support Pulse Instruments' clock driver and DC bias cards. The enhancements are transparent to the CompactPCI specification, and 3rd-party cards CompactPCI/PXI cards can be used in our mainframes without hardware or software modification*.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - 6U VPX
Model 57760
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four or eight 200 MHz 16-bit A/Ds- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Sample clock synchronization to an external system reference LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Phoenix LVDS Frame Grabber (PE1)
AS-PHX-D36-PE1
-
Phoenix-D36 is a PCI Express board for the acquisition of digital data from a variety of sources, including digital frame capture and line scan cameras. It has 36 bits used for input data, with 4-bits for control. This provides support for a single 12 bit RGB or 32 bit mono data source, including multi-tap cameras. The 4-bit control inputs are dedicated as Frame Enable, Line Enable, Data Enable and Pixel Clock.
-
Product
Earth Ground Meters
-
The earth tester determines ground resistance for both specific and ohm resistances. The earth tester is powered by batteries and have a clock timer function (3 minutes), Data-Hold function, a 3 ½ positions LCD display and their dimensions are 163 x 100 x 50 mm. Resistance ranges come from 20, 200 to 2000 ohms. They have a resolution of 10 / 100 mΩ / 1 Ω. The earth tester measure resistance by means of a constant reverse current (approx. 800 Hz, 2 mA). To measure ground voltage a rectifier is used (5 kΩ/V aprox. 40...500 Hz). The earth tester PKT-2630 series have a small format as well as multiple functions.
-
Product
16, 32, And 48 Channel Isolated Solid-State Output Cards With External Clocking
PCI-IDO-xxA Series
-
PCI-IDO-xxA Series cards offer a range of 16, 32, or 48 individual, optically isolated differential outputs. These cards are ideal for use in control and instrumentation applications where high-voltage protection is required. Individual channel-to-channel isolation allows every channel to be physically and electrically separated from the others.
-
Product
2-Channel 500 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - 6U VPX
Model 57650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Filter Building Blocks
-
Analog Devices offers an extensive line of continuous time and clock tunable (switched capacitor) filter building blocks. These devices were designed to simplify the implementation of band-pass, high-pass, low-pass, notch, or all-pass filters using classical filter realizations (such as Butterworth, Cauer, Bessel, and Chebyshev).
-
Product
PCI Express A/D Board
AD14-500 Series - Dual 14 bit, 500 MS/s
-
The AD14-500 series has two 20-500 MS/sec 14-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at up to 4GB/sec (500MS/s * 2 bits per sample * 2 channels). Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
Product
High Impedance Differential Clock Divider
-
Alliance Support Partners, Inc.
he ASP-DCD-00 board is a high impedance input clock divider circuit. It is designed to provide minimum load to a clock source for frequency measurement. It accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms; it divides the input signal frequency from 2 to 256 times depending on shunt jumper selections on J3. The board requires 5VDC 500mA power source to operate. The output is capable of driving 5V TTL logic levels.
-
Product
CMOS/CCD Production Test System
System 1828
-
The basic system consists of a 225 MHz pattern generator, 10 clock drivers, 6 DC biases, 1-4 channels of 10 MHz 14 bit analog data acquisition and/or 1-4 channels of digital acquisition. Additional options can be added to customize the system to meet your requirements.
-
Product
High Frequency Clock Divider Board
-
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
Product
PCIe Adapter for PMC
PCIe4LBPCI
-
Now you can use your PCI with a new PC. The new PC´s have PCI Express connectors in larger quantities than PCI slots. PCIe4LBPCI ( PCIe Bridge PCI 1 position) adapter / carrier converter card provides the ability to install one PCI card into a standard PCIe (Express) 4 lane slot. Suitable for PCI or PCI-X operation with the PCI; 32 bit or 64 bit data and PCI (25, 33, 50, 66) or PCI-X (50,66,100,133) MHz. clock. Auto selected or switch programmable speeds. The bridge can operate with 1, 2, 3 or 4 lanes active, and can be installed into slots with more than 4 lanes if desired.
-
Product
Mezzanine System
5174
System
The 5174 provides two major functions, serving as a precision Voltage Controlled oscillator board and a variable frequency source board. These features can be use together or independently. As a variable frequency source, the 5174 provides a high-resolution variable clock source that is based upon a reference clock supplied by the ECM carrier.
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 57621
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUCs (digital upconverters)- Two 800 MHz 16-bit D/As- One multiboard programmable beamformers- 2 GB of DDR3 SDRAM; 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Logic Analyzer
LAP-322000U-A
-
Zeroplus Technology Corperation
Sample rate (Internal clock): 200MHz asynchronous operationSample rate (External clock): 100MHz synchronous operationMemory Depth (per channel): 2MbitsChannels: 32CH
-
Product
Digital Thermo Hygrometer
-
Digital temperature humidity meters. Temperature humidity meters with clock Table mountable wall Mountable
-
Product
NI-6584, 16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
781290-03
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.
-
Product
4-Ch 500 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Kintex UltraScale - 6UVPX
Model 58851
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- Four 500 MHz 12-bit A/Ds- Four multiband DDCs (digital downconverters)- Two DUC (digital upconverter)- Four 800 MHz 16-bit D/As- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Optional 400 MHz 14-bit A/Ds- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI Multi-Channel Function Generator Module, 32-Channel
41-625-001
Function Generator
The 41-625-001 (PXI) and 43-625-001 (PXIe) are function generator modules that provide 32 channels in a single PXI/PXIe slot. They can generate sine waves to 300 kHz with 5.76 mHz frequency resolution referenced to the 10 MHz PXI clock. The output voltage range is up to +/-25 V in a 16-bit resolution. It also support PXI trigger functions allowing events from other instruments to initiate waveform generation or sweeps.
-
Product
PXIe-5650, 1.3 GHz RF Signal Generator
781215-01
RF Signal Generator
The PXIe‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
USRP-2974, 10 MHz to 6 GHz, x86 Processor, GPS-Disciplined OCXO, USRP Software Defined Radio Stand-Alone Device
785606-01
-
The USRP-2974 is built on the LabVIEW reconfigurable I/O (RIO) architecture with an onboard Intel Core i7 processor running the NI Linux Real-Time OS. The USRP-2974 is a USRP Software Defined Radio Stand-Alone Device, meaning that you can target the onboard processor with LabVIEW Communications System Design Suite to deterministically perform processing. The USRP-2974 is also equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock. You can prototype a range of advanced research applications that include stand-alone LTE or 802.11 device emulation; Medium Access Control (MAC) algorithm development; multiple input, multiple output (MIMO); heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Static Design Verification
ALINT-PRO
-
ALINT-PRO™ is a design verification solution for RTL code written in VHDL, Verilog, and SystemVerilog, which is focused on verifying coding style and naming conventions, RTL and post-synthesis simulation mismatches, smooth and optimal synthesis, correct FSM descriptions, avoiding problems on further design stages, clocks and reset tree issues, CDC, RDC, DFT, and coding for portability and reuse. The solution performs static analysis based on RTL and SDC™ source files uncovering critical design issues early in the design cycle, which in turn reduces design signoff time dramatically. Running ALINT-PRO before the RTL simulation and logic synthesis phases prevents design issues spreading into the downstream stages of design flow and reduces the number of iterations required to finish the design.
