-
Product
4 Digits Temperature(TC) Meter
CM1-TC
-
CM1-TC Thermocouple Temperature Meter has been designed in simple function and 4 digital 20.0mm LED displays with economic cost.They are can be programmed by tact switches that are hidden in front panel.They are also available to option relay output or an analog output or RS485(Modbus RTU Mode) communication.
-
Product
10 MHz To 54 GHz LAN Thermal Vacuum Compliance Power Sensor
L2066XT
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Test Executive for Visual Development, Database Storage, and Run-Time Execution of Test Strategies
TestBase
-
TYX TestBase is a test executive that supports the visual development, database storage and run-time execution of test strategies (also known as test plans or test sequences).TestBase integrates third-party applications such as: test programming languages, document viewers, report generators, database engines, Configuration Management systems and diagnostic tools.Its modular and open architecture enables system integrators and end-users to customize and extend the product and to integrate additional third-party applications.
-
Product
JTAG Debug Probe for Cortex-M
J-Trace PRO
-
SEGGER Microcontroller GmbH & Co. KG
J-Trace PRO for Cortex-M is setting a new standard for trace probes. It enables continuous streaming trace via its Gigabit Ethernet interface, lifting the limitations by internal buffers and slow data transmission.J-Trace PRO can capture omplete traces over long periods - thereby enabling the recording of infrequent, hard-to-reproduce bugs. This is particularly helpful when the program flow 'runs off the rails' and stops in a fault state. It also supports extended trace features, such as code coverage (so engineers have visibility of which parts of the application code have been executed) and execution profiling (providing visibility as to which instructions have been executed and how often - so hotspots can be addressed and optimization opportunities identified).
-
Product
Service Management Software
CERDAAC
-
CERDAAC® is an advanced software service that integrates calibration, maintenance, and service management for assets serviced by SIMCO, internal departments, or other service vendors.A secure cloud-based service, CERDAAC is a proven solution that helps thousands of organizations increase efficiency, improve compliance, and reduce costs. CERDAAC provides advanced asset and service workflow management and visibility into service status, program spending, quality compliance, key performance metrics, and more.Learn more about CERDAAC Service Manager and SIMCO Manager, as well as the optional Compliance Module.
-
Product
Posi-Control System
-
The position control system consists of a torque arm equipped with an encoder and a posi-control device. The touch posi-control system is used for programming and it to track the movement of the position control torque arm.
-
Product
Turns Ratio Testers
TRT Advanced Series
-
TRT Advanced series is the newest DV Power solution for transformer turns ratio measurement. Besides its main application, each turns ratio tester from this series also measures transformer excitation current and phase shift. Furthermore, all models perform automatic vector group detection and magnetic balance on three-phase transformers and three-phase autotransformers. They have a built-in true three-phase power source. For that reason, they can test transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.The instruments can output test voltages from 1 V AC to 500 V AC, depending on the model. With the highest test voltage 500 V AC, TRT500 provides the most accurate turns ratio testing of power transformers used in power generation and transmission. The output test voltage of TRT500 can be boosted to 5 kV AC using the external CVT20 extension transformer. This application is specially designed for testing turns ratio of capacitive voltage transformers. The other three models, TRT400, TRT250, and TRT100 can output up to 400 V, 250 V, and 170 V respectively. The low test voltage of 1 V AC enables turns ratio verification of current transformers.TRT500 is equipped with a large 10.1” graphical touch screen display. Other models, (TRT400, TRT250, TRT100) have 7” graphical touch screen display. Besides making the interface much more user-friendly compared to older turns ratio testers, it also brings certain options that were previously available only with DV-Win software. The most important are test templates and automatic test mode. Users can simply create test templates, store them in the instrument’s memory, and load when in the field with just a few clicks.This turns ratio test set, as well as all other DV Power turns ratio testers, has a built-in tap changer control unit. It enables remote control of an on-load tap changer (OLTC) directly from the instrument. In order to make the most out of this feature, the instrument can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option, especially in combination with test templates, significantly facilitates and shortens the turns ratio testing time. Automatic test mode minimizes human errors, which makes the measurement more reliable.
-
Product
MIL-STD-1760
M4K1553Px(S)-1760
-
The M4K1553Px(S)-1760 interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M4K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M4K1553Px-1760 modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.
-
Product
Custom Development
-
Specially developed power supplies require extensive industry knowledge. If, despite the wide range of COTS products, we do not have a suitable power supply for your application in the standard range, we will be happy to develop power supply solutions with our experienced engineering for your need. The development work can include both electronic and mechanical constructions, as well as programming.
-
Product
PCI-7811, 1M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779363-01
Digital I/O Module
The PCI‑7811 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7811 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
Product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781028-01
Strain/Bridge Input Module
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Megohmmeter Insulation Tester
AMIC-30
-
The AMIC-30 insulation tester is a small portable meter designed to measure insulation resistance in electrical and telecommunications installations, cables, motors, transformers and other equipment. The test voltage can be programmed in steps from 10 V to 1000 V. The instrument can measure both insulation resistance over a wide range (0,1kΩ...100GΩ), and insulation leakage current, capacitance and other parameters. All test results can be stored in the internal memory and sent to a computer via the included wireless USB receiver. The meters are supplied with rechargeable Ni-Cd batteries.
-
Product
C Series Universal Analog Input Module
Analog Input Module
The C Series Universal Analog Input Module helps you perform multi-purpose measurements. This module includes built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. You also can choose options to measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors.The C Series Universal Analog Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Test Adapter
-
Development of a 12-way test and programming adapter from Toptest for ?? The Dash ?? from Bragi, a wireless, intelligent earphone with communication and sensor technology. With the first version of the test adapter, only a purely sequential testing was possible due to the interdependencies of the tests. In version 3.0, the now autonomous tests were brought into a parallel TestStand sequence. In addition, individual sockets were prioritized in order to optimally use the hardware resources. This resulted in a time advantage of 80% compared to the initial situation.
-
Product
Stand-Alone Programmer and Hardware Debug Interface
Cyclone MAX
-
Cyclone MAX is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale ColdFire V2/V3/V4, Power Architecture 5xx/8xx, Power Architecture 55xx/56xx (Nexus), and ARM (MAC7xxx) microcontrollers.
-
Product
Battery Test Software
-
Landt Battery Test Systems use different programs for data acquiring and data process. The acquiring software comes with a very user-friendly interface, which allows new users to operate with minimal training. Data process software shows different kinds of plots (Voltage vs. Capacity, Capacity vs. Cycle Number, Efficiency, etc.), which can be easily exported.
-
Product
PCI-8512, 2-Port, High‑Speed/FD CAN Interface Device
780683-02
CAN Interface
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
TCS Comfort
-
Maschinenbau Haldenwang GmbH & Co. KG.
Trip distance / tachograph meter integrated into the brake tester (only in conjunction with PC)Electronic control unit TCS shockproof (workshop-oriented) aluminum housing with connection D-Sub 25p / D-Sub 9pEntire operation via integrated time and data display, and your existing PC (OS: Windows).Complete measurement and programming of the tachograph types 1311, 1314, 1318, 8400, FTCO 1319 MTCO 1324, TVI 2400, SE 5000, EFAs, SmarTach, DTCO 1381 incl. Integrated dial measurementLCD 4 rows, 16 digits; backlit with an integrated smart card readerMobile and / or stationary usable instrument; used stationary as integrated into the brake tester and the computer; optionally a road measurement is possible.Expression of complete test reportData storage for customer and vehicle datamultilingualism
-
Product
PLC-Interoperable IIoT Gateway
GW-01
IoT Gateway Platform
The GW-01 is powered by iM-Connect, a web-based and simple-to-use programming software that support a variety of industrial communication protocols, PLC drivers, and IIoT cloud connections as a simple but reliable protocol conversion and data acquisition platform for connected industries.
-
Product
Performance Exams
-
Sturdy sheet steel housing with safety door and electrically driven base with built-on sample mold. The compaction takes place via a rolling segment with force / path-controlled drive device from above. The sample mold and the rolling segment are equipped with software controlled heating. The measurement of force and displacement is done by electronic sensors. The entire compaction process is controlled with Windows software and PC via preselected sequence programs.
-
Product
5V50mA Coin Cell Battery Test Equipment
TOB-5V50mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Test Equipment (0.1-50mA, up to 5V) For Lithium Coin Cell Battery Research. TOB-5V50mA Battery Test Equipment is an eight-channel battery analyzer to analyze small coin cells with a range current 0-50mah, voltage 0-5v. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be programmed and controlled by computer software.
-
Product
Integrated Test Facility
ITF
-
The ITF, located in El Segundo, California, has multiple test stations to enable parallel testing and significantly streamline program test schedules. More than 25,000 square feet are available for integration and test activities, including a 10,000-square-foot Class 10K clean room. Our facilities feature thermal vacuum chambers and test stations to support optical alignment, warm optical bench testing, and hardware integration.
-
Product
ARINC 429 Multichannel Interface Card for Mini PCI Systems
DAS-429mPCI/RTx
Interface Card
The DAS-429mPCI/RTx is an ARINC 429, multichannel interface card for Mini PCI systems. The card’s small size and suitability for Mini PCI notebook computers, make them a complete solution for developing and testing ARINC 429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The DAS-429mPCI/RTx is supplied with C drivers, including source code and Mystic application program.
-
Product
Super Fast Gang ISP Programmer
448Pro2
-
The Dataman 448Pro2 is a super fast PC based gang programmer with four independent 48-pin ZIF sockets, ISP capabilities and USB 2.0 connectivity • Up to 75% faster programming of high-capacity memory devices • Over 105,000 devices supported with new devices added monthly • Independent modules supporting concurrent programming • Intelligent pin drivers operate down to 1.8V so you'll be ready to program the full range of advanced low-voltage devices • Full ISP capabilities including JTAG compatibility • Hi-speed USB 2.0 connectivity • Easy to use software compatible with the latest operating systems including Windows 10 • Comprehensive 3 years parts and labor warranty • Free life-time software updates
-
Product
Digital Bit Pattern Generator
FAB-3226
Function Generator
The FAB-3226 Digital Bit Pattern Generator connects digital ports to an user-defined FPGA logic. As the FPGA is user-programmable all kind of operation can be implemented: input, output, and closed loop operation where input and output are processed in real-time. All this can be controlled by an user-defined application program running on a computer system (PC or embedded).
-
Product
Horizontal High-Speed Multi-Head Gage
1304/1306:
-
The Adcole Model 1304/1306 four-headed gage offers three different horizontal load options for increased throughput. The Model 1304/1306 can switch between multiple part types at the touch of a button. An automated version, ready for load by gantry or robot, is also available available.The flexibility and versatility of this gaging system is comparable to a single-headed gage, but this gage completes part inspection in a fraction of the time. Despite the tremendous gains in cycle time, there is no sacrifice in accuracy or capability. Changing between part types is remarkably simple; tailstock adjustments are fast and easy. With the user-friendly Windows platform, programming and output report formatting is flexible and straightforward. Similar to other Adcole gage models, reporting can provide actual measured dimensions and tolerance deviations for easy interpretation.
-
Product
Humidity Chamber
HCP
-
Does your application temperature lie between 8 C above room temperature and 90C, with controllable humidity? Then the Memmert humidity chamber HCP is unbeatable in price, performance and comfort. The almost unlimited programming possibilities of temperature profiles make ideal environmental conditions for the load possible.
-
Product
Rock Mechanics
ROCK3D
-
ROCK3D is a program for stability analysis of removable blocks on planar rock slopes. It identifies and analyses all the blocks that have formed under each kinematic mode. Once the geometry of the rock blocks has been identified, the bolt forces necessary to reach a required safety factor are calculated.
-
Product
Microelectronic Services
-
Services for ASIC houses and Integrated Device Manufacturers are IC Wafer / Final Test, IC assembly, Test Program development, product engineering, Flash / EEPROM programming, characterisation / capability studies, yield enhancement, design verification and failure / yield analysis. Das Test Haus are specialists for wafer test, low power, mixed signal and eeprom test.
